Choosing engine oil for Nissan - a task that requires attention to detail. Even if you are not an expert in auto chemicals, understand the difference between 5W-40 and other viscosities are critically important: engine life, fuel consumption and even ride comfort depend on it. This is especially true for owners of models with turbocharged engines (Qashqai J11, X-Trail T32, Navara D40), where lubrication requirements are higher.

But why exactly 5W-40, and not, say, 0W-20 or 10W-60? It's all about balance: this viscosity ensures easy cold starts (figure 5W indicates winter properties) and reliable protection at high temperatures (index 40 responsible for summer stability). However, not everything is so simple: the manufacturer Nissan has strict tolerance requirements, and not every oil is marked 5W-40 suitable for your car. In this article, we will look at how not to make a mistake when choosing, what original oils are filled in by the dealer, and what can be used to replace them without risk to the engine.

Original Nissan 5W-40 oil: part numbers and features

Official service centers Nissan use motor oils of their own brand - Nissan Motor Oil. For viscosity 5W-40 Two main products are relevant:

  • 🔧 KE900-90132 - synthetic oil Nissan Strong Save X E 5W-40, meets the standard API SN And ILSAC GF-5. Suitable for petrol and diesel engines (including turbocharged ones).
  • 🔧 KE900-90135Nissan Strong Save X E 5W-40 (Low SAPS), low-sulfur oil for modern engines with exhaust gas aftertreatment systems (for example, Qashqai J11 with engine MR20DD).

Both options are manufactured by Eneos (Japan) upon request Nissan and have the same base, but differ in the additive package. Important nuance: original oil KE900-90135 often counterfeited - it can only be bought from official dealers or in trusted stores with certificates.

Cost of original oil Nissan 5W-40 varies from 3,500 to 5,000 rubles per 5 liters (for 2026). This is more expensive than analogues, but is justified by the stability of characteristics and a guarantee of compatibility with engines Nissan. However, not all owners require the original - we’ll talk about this later.

📊 What oil do you use in your Nissan?
  • Original Nissan 5W-40
  • Analogue (Mobil, Castrol, Liqui Moly)
  • Other (specify in comments)
  • I don't know what's in there

Tolerances and specifications: what to look for on the label

It is not enough to simply buy oil labeled 5W-40. For engines Nissan critical manufacturer's approvals, which indicate compliance with technical requirements. Basic standards that should be on packaging:

Standard Description For which models Nissan
API SN Modern standard for gasoline engines (since 2010). Replaces SM. Qashqai J10/J11, X-Trail T31/T32, Teana L33
ILSAC GF-5 Energy-saving standard for Japanese and Korean cars. Compatible with API SN. Juke F15, Note E12, Almera N18
ACEA A3/B4 European standard for high-load petrol and diesel engines. Navara D40, Pathfinder R51, Patrol Y62 (diesel)
Nissan Approval Company clearance Nissan (For example, Nissan PSF-2 for hybrids). Ariya, Leaf, Serena C27 (with system e-Power)

⚠️ Attention: If the canister does not have at least one of the required standards (API SN or ILSAC GF-5 for most gasoline Nissan), such oil cannot be filled. Even if the seller assures that it is “suitable in viscosity.”

For turbocharged engines (GT-R R35, 370Z, Qashqai 1.6 DIG-T) additional compliance is required ACEA A3/B4 or MB 229.5 (tolerance Mercedes-Benz, which is often used as a guide for highly loaded motors).

What does "Low SAPS" mean in oil?

Low SAPS (Low Sulfated Ash, Phosphorus, Sulfur) are oils with a low content of sulfur, phosphorus and sulfated ash. They are designed for modern engines with catalysts and diesel particulate filters (DPF), as they reduce clogging. For example, oil Nissan KE900-90135 belongs to this category and is recommended for diesel engines Navara and gasoline engines with a system EcoBoost.

Top 5 analogues of Nissan 5W-40 oil: what to choose instead of the original

Original oil Nissan not always available or justified in price. Fortunately, there are proven analogues that are not inferior in quality, and sometimes even surpass it. The main thing is to comply with tolerances and choose products from well-known brands.

Here 5 best options to replace:

  • 🏆 Mobil 1 ESP 5W-40 - fully synthetic oil with approval MB 229.51 And VW 504 00. Ideal for turbocharged Qashqai And X-Trail with direct injection.
  • 🛢️ Castrol Edge Professional LL 5W-40 - designed for BMW Longlife-04, but also suitable for Nissan with turbocharging. Excellent oxidation resistance.
  • 🔥 Liqui Moly Top Tec 4200 5W-40 - universal oil with approvals API SN And ACEA A3/B4. Shows well in Teana V36 And Maxima A35.
  • 🚗 Motul Specific Dexos2 5W-40 - corresponds GM Dexos2, but also suitable for Nissan with diesel engines (for example, Navara 2.3 dCi).
  • 💎 Idemitsu Zepro Touring 5W-40 — Japanese oil, close in composition to the original Nissan. Recommended for naturally aspirated engines (Almera N18, Tiida C13).

⚠️ Attention: If your Nissan under warranty, the use of non-original oil may result in refusal of service. In this case, it is better to overpay for KE900-90132 or KE900-90135than to risk.

Critical point: oils labeled "Energy Conserving" (e.g. ILSAC GF-6) may be too "thin" for older engines Nissan (until 2010 release). In such engines it is better to use 5W-40 with permission API SL instead of SN.

☑️ How to check oil before buying

Done: 0 / 4

When and how often to change 5W-40 oil in Nissan

The frequency of oil changes depends on several factors: engine type, operating conditions and the quality of the oil itself. Manufacturer Nissan recommends the following intervals:

  • 📅 Gasoline naturally aspirated engines (Almera N18, Note E12): every 15,000 km or once a year.
  • 🔥 Turbocharged gasoline engines (Qashqai 1.6 DIG-T, Juke 1.6T): every 10,000 km or once every 8 months.
  • Diesel engines (Navara 2.5 dCi, X-Trail 2.0 dCi): every 10,000–12,000 km.

However, these figures are relevant for ideal conditions: quiet ride, high-quality fuel, no overloads. In reality, the replacement interval should be reduced by 20–30% if:

  • 🚦 You often get stuck in traffic jams (the oil overheats).
  • 🏔️ Drive off-road or in mountainous areas.
  • ❄️ You operate the car at extreme temperatures (below −30°C or above +35°C).

⚠️ Attention: In engines with a system Start/Stop (For example, Qashqai J11) oil 5W-40 ages faster due to frequent starts. In this case, replace it via 8,000–9,000 km, even if the mileage is less.

💡

Before changing the oil, warm up the engine to operating temperature (60–70°C) - this will help drain the maximum amount of waste and remove sludge.

Step-by-step instructions for changing the oil in Nissan

If you decide to change the oil yourself, follow these instructions. It is universal for most models Nissan (except GT-R And 370Zwhere special equipment is required).

What you will need:

  • 🔧 New oil 5W-40 (see table below for volume).
  • 🛢️ Oil filter (original items: 15208-9M50A for Qashqai, 15208-65F0E for X-Trail).
  • 🔩 Drain plug key (usually on 14 or 17).
  • 🧰 Oil filter puller (if it is screwed tightly).
  • 📦 Funnel and container for working out (minimum 5 liters).

Sequence of actions:

  1. Start the engine and let it run for 3-5 minutes to warm up the oil.
  2. Lift the car on a lift or drive it into a pit. Make sure the car is level.
  3. Unscrew the drain plug (it is located on the pan) and drain the oil into a container.
  4. While the oil is draining, replace the oil filter. Before installing the new filter, lubricate the rubber seal with fresh oil.
  5. Screw on the drain plug with a new O-ring (if included).
  6. Pour new oil through the filler neck using a funnel. Check the level using the dipstick.
  7. Start the engine, let it run for 1-2 minutes, then check the level again and top up if necessary.
Model Nissan Oil volume (with filter), l Oil filter part number
Qashqai J11 (1.6/2.0) 4.6 15208-9M50A
X-Trail T32 (2.0/2.5) 4.8 15208-65F0E
Navara D40 (2.5 dCi) 7.4 15208-ED30A
Teana L33 (3.5 V6) 4.5 15208-65F0B

⚠️ Attention: After changing the oil, reset the service interval in the on-board computer. To do this:

  1. Turn on the ignition (without starting the engine).
  2. Click the button TRIP and hold it for 10 seconds.
  3. Turn the key to position ON and wait for the indication to appear OIL.
  4. Click again TRIP and hold until the indicator goes off.
💡

Never mix oils of different brands or viscosities. If topping up is necessary, use the same product that is in the engine.

Common mistakes when choosing and changing oil

Even experienced car owners sometimes make mistakes that can cost the engine its lifespan or even major repairs. Here are the most common of them:

  • 🚫 Ignoring Tolerances. Buying oil only by viscosity (5W-40) without checking standards (API SN, ACEA A3/B4).
  • 🕳️ Saving on filter. Cheap non-original filters may not retain dirt particles, which leads to engine wear.
  • 🔄 Incomplete drainage of old oil. If you do not warm up the engine before replacing, up to 0.5 liters of waste will remain in the crankcase, which will worsen the properties of the new oil.
  • ⚠️ Exceeded oil level. Excess oil leads to increased pressure and the risk of squeezing out the seals.
  • 📅 Violation of replacement intervals. Even if the mileage is low, the oil ages over time (oxidizes, loses additives).

A separate story - fakes. There are a lot of counterfeit branded oils on the market Nissan, Mobil, Castrol. How to recognize:

  • 🏷️ Low price (original Nissan 5W-40 cannot cost less than 3,000 rubles. for 5 l).
  • 📦 Uneven seams on the canister, blurry font on the label.
  • 🔍 No hologram or serial number.

If you doubt the originality of the oil, check it against serial number on the manufacturer's website or buy from an official dealer.

Owner reviews: which 5W-40 oil is best for Nissan

To form an objective opinion, we analyzed reviews from owners Nissan on the forums (Drive2, Nissan-Club) and on social networks. Here's what they say:

Original oil Nissan 5W-40 (KE900-90132):

  • Pros: stable engine operation, no waste, good protection in cold weather (−30°C).
  • Cons: high price, often counterfeit, difficult to find in the regions.

Mobil 1 ESP 5W-40:

  • Pros: excellent cleaning ability, suitable for turbo engines, reduces fuel consumption.
  • Cons: expensive (about 4,500 rubles for 5 liters), can be “thin” for older engines.

Liqui Moly Top Tec 4200 5W-40:

  • Pros: versatility (suitable for gasoline and diesel), low waste, good reviews from owners X-Trail.
  • Cons: in some cases, increased noise of hydraulic compensators was noticed after replacement.

Castrol Edge Professional LL 5W-40:

  • Pros: high thermal stability, recommended for Qashqai 1.6 DIG-T.
  • Cons: the price is comparable to the original, not always in stock.

💬 Conclusion from reviews: If the budget allows, the majority of owners recommend the original oil Nissan or Mobil 1 ESP. Suitable for saving Liqui Moly or Idemitsu Zepro, but it is important to monitor replacement intervals.

FAQ: Frequently asked questions about Nissan 5W-40 oil

Is it possible to use 5W-40 instead of 5W-30 in Nissan?

Depends on the model and year of manufacture. For most Nissan after 2010 5W-30 — basic recommendation (fuel savings, less resistance). However 5W-40 allowed in the following cases:

  • 🔧 Engine with a mileage of more than 150,000 km (needs a thicker film).
  • 🏔️ Operation in hot climates or with high loads (for example, towing a trailer).
  • 🔥 Turbocharged engines (Qashqai 1.6 DIG-T, X-Trail 2.0 Turbo).

⚠️ Important: If the instructions only indicate 5W-30, fill 5W-40 may lead to increased fuel consumption and stress on the oil pump.

How much 5W-40 oil does a Qashqai J11 need to change?

The volume depends on the engine type:

  • 🔧 1.6 (HR16DE): 4.3 l (with filter - 4.6 l).
  • 🔥 1.6 DIG-T (MR16DDT): 4.8 l (with filter - 5.1 l).
  • 🚗 2.0 (MR20DD): 4.4 l (with filter - 4.7 l).

Always buy oil with a reserve (5 liters), as some will remain in the filter and on the engine walls.

What happens if you exceed the oil change interval?

The consequences depend on the mileage and operating conditions:

  • 🔥 10,000–15,000 km above normal: increased wear of parts, sludge formation, poor starting in cold weather.
  • 🚨 20,000+ km above normal: risk of rings sticking, damage to the turbine (if any), increased oil consumption due to waste.
  • ⚠️ 30,000+ km: engine overhaul (wear of liners, scuffing of cylinders).

💡 Advice: If you miss a replacement, don't wait until the next interval. Drain the old oil as soon as possible and flush the engine with a special fluid (for example, Liqui Moly Oil-Schlamm-Spulung).

Is it possible to mix different 5W-40 oils?

Mixing allowed only in emergency cases (for example, if you need to top up on the road). Rules:

  • 🔄 Use oils one brand and with the same tolerances (API SN, ACEA A3/B4).
  • 🚫 Don't mix synthetics And semi-synthetics.
  • 🔧 After mixing, change the oil and filter as soon as possible.

⚠️ Important: If you add another oil, do not load the engine (avoid high speeds and long trips).

Which 5W-40 oil is best for Nissan with mileage over 200,000 km?

For engines with high mileage, oils with increased cleaning properties And improved viscosity:

  • 🏆 Liqui Moly Hochleistungs 5W-40 — contains additives to restore the elasticity of oil seals.
  • 🛢️ Castrol Magnatec Stop-Start 5W-40 — protects against wear during frequent starts.
  • 🔧 Mobil Super 3000 X1 5W-40 - a budget option with good reviews.

💡 Advice: In older engines, avoid oils labeled Energy Conserving - they can cause leaks through worn seals.