Nissan Almera G15 (2012–2019) is a popular sedan that is often the target of tuning and repair. One of the key elements of comfort and safety is the seats. But how to choose the right ones? The original ones are expensive, and there are a lot of analogues on the market with different fastenings, sizes and materials. In this article we will look at all the nuances: from standard parameters to non-obvious installation life hacks.

It is important to understand that the wrong choice of seats can lead not only to discomfort, but also to problems with seat belts, operation of airbags (airbag) or even fines when passing a technical inspection. We analyzed manufacturer data, owner reviews and technical documents to gather up-to-date information.

Original seats for Nissan Almera G15: articles and features

Factory seats for Almera G15 are produced under article numbers that depend on the configuration and year of manufacture. Main original parts:

  • πŸͺ‘ Driver's front seat: 26500-4M000 (fabric) / 26500-4M010 (leather, for top versions)
  • πŸͺ‘ Front passenger seat: 26600-4M000 (fabric) / 26600-4M010 (skin)
  • πŸ›‹οΈ Back seat: 26700-4M000 (full sofa) / 26700-4M010 (with armrest for versions TEKNA)

The original seats are different integrated head restraints (except for the rear sofa), height adjustment (only in configurations Comfort+ And TEKNA) and fastenings under ISOFIX on the back row. Important: models before 2015 used fastenings with 4 fixation points, and after - with 6th (additional clamps for lateral stability).

The cost of new original seats starts from 25,000 rubles for the front (fabric) and reaches 60,000 rubles for a leather set. Used options can be found cheaper at salvage yards - from 8,000 to 15,000 rubles, but there is a high risk of purchasing worn or damaged copies.

πŸ“Š Which seats do you prefer for Almera G15?
  • Original Nissan
  • Analogues from other cars
  • Sports (Recaro, Sparco)
  • Budget non-original

Dimensions and fastenings: what you need to know before buying

The main parameter when choosing seats is compliance of seats and fastenings. For Almera G15 The following sizes are valid:

Seat type Width(cm) Depth (cm) Height (cm) Fastenings
Front (driver/passenger) 52–54 50–52 85–90 (with headrest) 4 or 6 points (depending on year)
Rear (sofa) 138–140 48–50 70–75 (without headrests) ISOFIX + 2 belts
Sports (Recaro, Sparco) 50–56 48–54 80–95 Universal slides or adapters

Pay special attention location of seat belt anchors. B Almera G15 front seat belts are attached not to the seat, but to the body (unlike many European cars). This means that you can install seats without built-in belt anchors, but At the same time, be sure to check compatibility with standard fixing points on the thresholds.

Rear seats have standard mountings ISOFIX for child seats. If you are installing a non-original sofa, make sure that the holes for ISOFIX coincide with the factory ones (the distance between them is 280 mm).

⚠️ Attention: When replacing front seats with heated or power models, you will need flashing the control unit (if you connect non-original electrics). Otherwise, errors may appear on the dashboard.

Compatible analogues: seats from other cars

Original seats for Almera G15 often replaced with analogues from other models Nissan or concern Renault-Nissan-Mitsubishi. Here are the tested options:

  • πŸš— Nissan Note E12 (2012–2016): Front seats fit almost perfectly, but may vary in height adjustment.
  • πŸš— Renault Logan/Sandero 2 (2012–2020): the rear sofa is interchangeable, the front seats require modification of the fastenings.
  • πŸš— Datsun on-DO/mi-DO: budget option, but the quality of materials is worse. Only basic versions without electric drives are suitable.
  • πŸš— Mitsubishi ASX (until 2017): sports seats with good lateral support, but require adapters for fastenings.

When choosing analogues, consider three key points:

  1. Coincidence landing dimensions (width and depth).
  2. Type fastenings (4 or 6 points).
  3. Availability holes for standard seat belts.

For example, seats from Renault Megane 3 They are similar in appearance, but have different fastenings and will not fit without modifications. But the front seats are from Nissan Juke F15 (2010–2019) can be installed with minimal modifications - you only need to move the mounting brackets.

πŸ’‘

Before purchasing analogues, check with VIN code your car. Some configurations Almera G15 had unique mounts for heated or memory seats.

Sports seats: Recaro, Sparco and other brands

Owners who want improved handling and comfort often install sport seats. Popular brands:

  • 🏁 Recaro: models Sportster CS or Pole Position - ideal for aggressive riding, but require adapters for mounts.
  • 🏁 Sparco: Revolution or Cobra Monaco - lightweight and durable, but can be tough for everyday use.
  • 🏁 OMP: Budget option with good lateral support, suitable for track days.
  • 🏁 Corbeau: models FX1 Pro or GTS II β€” universal, with adjustable lumbar support.

When installing sports seats, consider:

  1. Weight: Sports seats are often lighter than standard seats (e.g. Recaro Pole Position weighs ~10 kg versus 18 kg for the original).
  2. Fastenings: most models need universal skids (for example, from Sparco or Brimbo).
  3. Certification: Seats must be marked for legal use ECE R14 or FMVSS 207.

The cost of sports seats varies from 30,000 to 150,000 rubles per set. Please note that for a complete installation you may need replacing standard seat belts to 4-point (for example, from Schroth or Takata).

⚠️ Attention: Sports seats without certification ECE R14 will not pass inspection. Check the label or documentation for markings.

Make sure you have the ECE R14 certificate|Check the dimensions with the Almera G15 seat|Check the compatibility of the mounts (whether adapters are needed)|Assess the rigidity - is it suitable for everyday driving-->

How to remove and install seats: step-by-step instructions

Replacing seats in Almera G15 does not require special tools, but there are some nuances. You will need:

  • πŸ”§ Socket wrench on 14 mm (for front seats).
  • πŸ”§ Head on 10 mm (for the rear sofa).
  • πŸ”§ Screwdriver with a flat blade (for plastic clips).
  • πŸ”§ Torque wrench (optional, for precise tightening).

Removing the front seat:

  1. Pull the seat back as far as possible to gain access to the front bolts.
  2. Remove the plastic plugs on the guides (pry them off with a screwdriver).
  3. Unscrew 4 bolts (2 each front and rear) with a socket wrench on 14 mm.
  4. Disconnect the power connectors (if there is heating or electric drive).

Installing a new seat:

  1. Check the compatibility of the fasteners. Install adapters if necessary.
  2. Connect the electrics (if available). Use multimeterto check the polarity.
  3. Tighten the bolts firmly 40–50 Nm (Tightening may damage the threads).
  4. Check the operation of the seat belts and airbag (whether the light on the panel lights up).

For the rear sofa the process is simpler:

  1. Lift the front of the sofa and pull it up - it is fixed with two latches.
  2. Unscrew the 2 bolts under the plugs in the trunk (head on 10 mm).
  3. Disconnect the seat belts (if you are replacing the entire sofa).
What should I do if the airbag light comes on after installation?

If after replacing the seat the light on the panel comes on airbag, this means that the control unit has detected an error. Possible reasons:

1. Airbag connector not connected (check wiring harness under seat).

2. Incompatible unit firmware SRS (if seat with integrated airbag from another model).

3. Damaged seat occupancy sensor (a common problem when installing non-original seats).

Solution: reset the error via a diagnostic scanner (for example, Launch X431) or contact the service to reflash the unit SRS.

Tuning and restoration: how to update old seats

If the original seats are worn out but the mountings and frame are fine, they can be restored. Options:

  • 🧡 Padding: leather, Alcantara or quality fabric (e.g. Alcantara from 3M). Cost - from 15,000 rubles per set.
  • πŸ”₯ Spraying polyurethane foam: restores the shape of sagging seats. Price – from 8,000 rubles for one seat.
  • 🎨 Painting plastic elements: Suitable for worn armrests or sides. Use plastic paint (eg MOTIP).
  • πŸ”Œ Adding options: heating (Webasto or EberspΓ€cher), ventilation or massage (electrical modifications will be required).

For constriction they often use:

  • Leather: natural (expensive, but durable) or artificial (eco-leather).
  • Alcantara: improves grip on the body, but requires careful care.
  • Fabric: for example, Cordura (wear-resistant) or velor (soft, but marked).

When restoring, consider:

  • If the seat has side airbags, do not violate their integrity when re-tightening.
  • To maintain factory ergonomics, use original patterns when cutting materials.
  • After spraying the polyurethane foam, give the seat 24 hours Allow to dry completely before use.
πŸ’‘

Seat reupholstery is the most budget-friendly way to update the interior. However, if the seat frame is deformed (for example, after an accident), restoration will not help - only replacement.

Common mistakes when replacing seats and how to avoid them

Even experienced car owners make mistakes when replacing seats. Let's look at the most common ones:

  1. Ignoring seat belt anchorages:

    If new seats do not have the original seat belt holes, this may cause improper restraint of passengers and a fine during technical inspection. Solution: Use certified seats ECE R14 or install adapters.

  2. Incorrect bolt tightening:

    Weak tightening will lead to play in the seat, and excessive tightening will lead to thread breakage. Optimal force: 40–50 Nm for the front seats and 25–30 Nm for the back sofa.

  3. Electrical problems:

    If you connect heated or memory seats, check polarity and wire cross-section. Incorrect connection may damage the control unit or cause a short circuit.

  4. Airbag incompatible:

    Installing seats without an occupancy sensor or with a faulty airbag will result in SRS light stays on constantly on the panel. Solution: flashing the unit or replacing the sensor.

To avoid problems, follow a simple rule: Before purchasing seats, check their article numbers with the database ETIM or TecDoc. This will help ensure that the mounts and electronics are compatible.

⚠️ Attention: When installing seats from Renault or Datsun there is often a problem with seat belt sensor - it may not work, and a warning will light up on the panel. In this case, you will need to disable the sensor programmatically (but this violates traffic regulations).

FAQ: answers to frequently asked questions

Is it possible to install seats from a Nissan Almera N16 on a G15?

No, the seats are from Almera N16 (2000–2006) are not suitable for G15 due to different mountings and sizes. The exception is the rear sofa, but it will have to be modified (drilling new holes for fastenings).

Which seats are best for tall drivers?

For drivers taller than 185 cm, the following are suitable:

  • Original seats from Almera G15 TEKNA (with height adjustment).
  • Sports seats Recaro Sportster CS (with extended guides).
  • Seats from Renault Fluence (analogue Almera G15, but with greater depth).

Important: check maximum backrest recline - in some sports models it is limited.

How to check a seat during disassembly before purchasing?

When inspecting a used seat, pay attention to:

  1. Frame: are there any cracks or deformations (especially at the points of attachment to the body).
  2. Adjustment mechanisms: smooth running, no backlash.
  3. Sheathing: abrasions, tears, traces of repair.
  4. Electrician: If there is heating, check all heating zones with a multimeter.
  5. Airbags: check whether they worked (if so, the seat is only for scrap metal).
Do I need to register replacement seats with the traffic police?

According to Technical regulations of the Customs Union, seat replacement does not require registration if:

  • New seats are certified (ECE R14 or FMVSS 207).
  • The standard seat belt attachment points have been retained.
  • The body structure has not been changed (for example, no new holes have been drilled).

If you are installing sports seats with 4-point belts, you will need certificate for belts and making changes to the STS (as re-equipment).

Is it possible to install heated seats if they are not included in the standard version?

Yes, but you will need:

  1. Buy heated seats (original or universal).
  2. Route the wiring from the fuse box (use relay for protection).
  3. Install a control button (can be inserted into a standard panel or on the dashboard).
  4. Connect via 20A fuse.

The connection diagram can be found in the electrical manual Almera G15 (section Seat Heater).