Wipers for Nissan Murano Z50: how to choose and replace correctly

Wipers on Nissan Murano Z50 - it would seem a trifle, but not only comfort, but also driving safety depends on their condition. In rain or snow, worn blades leave streaks, impair visibility and force the driver to strain to see the road. However, many owners Murano face typical problems: creaking during operation, incomplete adherence to the windshield, or rapid wear of even expensive brushes.

In this article we will look at everything you need to know about wipers for Nissan Murano Z50 (2015–2022): from standard sizes and original part numbers to step-by-step replacement instructions. We will place special emphasis on choosing brushes for climatic conditions (winter vs summer), eliminating squeaks And Drive fault diagnosis. You will also find a compatibility table for analogues and answers to frequently asked questions that are not covered even in official manuals.

Dimensions and articles of original wipers for Nissan Murano Z50

On Murano Z50 wipers of non-standard length are installed - this is important to consider when purchasing. Original sizes:

• 🚗 Driver's wiper: 26 inches (660 mm)
• 🚗 Passenger wiper: 18 inches (457 mm)
• 🚗 Rear wiper (if installed): 12 inches (305 mm)

Official articles from Nissan:

Wiper type	Article	Note
Driver's (left)	28560-4M000	Frameless, heated (optional)
Passenger (right)	28561-4M000	Frame or frameless (depending on the configuration)
Rear	28580-4M000	Only for versions with rear wiper

⚠️ Attention: On restyled models Murano Z50 (from 2019) wipers with modified mount — check compatibility by VIN code or visually (mounting type U-hook or pin-type).

Frameless vs framed: which wipers are better for Murano Z50

The choice between frameless and frame brushes depends on the climate and driving style. Let's look at the pros and cons of each type:

Frameless wipers (For example, Bosch Aerotwin or Valeo Silencio):

• ✅ Better fit to glass due to flexible rubber.
• ✅ Less noise at high speeds (relevant for Murano with its aerodynamics).
• ❌ More expensive frame by 30–50%.
• ❌ Less stable to icing (rubber can harden in the cold).

Frame wipers (For example, Denso or Trico):

• ✅ Cheaper and easier to replace.
• ✅ They cope better with ice and snow.
• ❌ They creak when worn (especially on Murano with a large windshield).
• ❌ May come off from glass at speeds over 120 km/h.

🔹 Expert advice: For regions with frequent temperature changes (for example, Moscow, St. Petersburg) hybrid wipers — combine the flexibility of frameless and the strength of frame ones. Examples: Bosch Twin or HEYNER Hybrid.

Step-by-step instructions for replacing wipers on a Nissan Murano Z50

Replacing brushes with Murano Z50 takes no more than 10 minutes, but there are nuances that are missed even in service manuals. Follow the algorithm:

1. Preparation: Park the vehicle on a level surface and turn off the ignition (so that the wipers do not work automatically). Raise the levers perpendicular to the glass - they are fixed in this position.
2. Removing the old brush:
   • Click on plastic retainer at the base of the wiper (usually indicated by an arrow).
   • Pull the brush down (toward yourself) until it clicks. Do not pull to the side - you may break the fastener!
3. Installing a new brush:
   • Combine fastening new brush with lever (on Murano Z50 type used U-hook 9x3 or pin-type 4.8 mm).
   • Press up click - a characteristic sound should be heard.

Check: Turn on the wipers in single swing (button on the lever under the steering wheel) and make sure that the brushes do not catch each other.

⚠️ Attention: On Murano Z50 with the system Auto Wipers (automatic switching on of wipers) may be required after replacing the blades error reset in the control unit. To do this:

1. Turn on the ignition (without starting the engine).
2. Press and hold the button OFF on the wiper lever 10 seconds.
3. Turn off the ignition and turn it on again - the system will recalibrate.

Top 5 analogues of original wipers for Murano Z50

Original brushes from Nissan They are expensive (from 2500 rubles per set), but the market offers worthy analogues. We tested 15 brands and selected the best in terms of price/quality ratio:

Brand and model	Type	Service life	Price (set)	Features
Bosch Aerotwin AR660S/AR457S	Frameless	1.5–2 years	~2800 rub.	Better fit, quiet operation, but afraid of frost below -20°C.
Valeo Silencio X-TRM 660/457	Frameless	2 years	~3200 rub.	Resistant to UV radiation, suitable for southern regions.
Denso Hybrid 026-018/012-018	Hybrid	1 year	~2100 rub.	Optimal for winter, but creaks when worn.
HEYNER Hybrid 4000 660/457	Hybrid	1.5 years	~2500 rub.	Good for rainy climates (for example, Leningrad region).
Trico NeoForm 26-18-12	Frame	1 year	~1800 rub.	A budget option, but requires frequent replacement.

🔹 Critical information: On Murano Z50 with panoramic roof (optional SkyView) standard wipers can aim at the seal at maximum lift. In this case, choose brushes with shortened lever (For example, Bosch Aerotwin Short).

Why wipers squeak on Nissan Murano Z50 and how to fix it

Wipers creaking Murano Z50 - a common problem that occurs even with new brushes. Causes and solutions:

• 🔧 Glass contamination:
  • Tar, pollen or bitumen stains create uneven surfaces. Clean the glass special cleaner (For example, Sonax Glass Cleaner) or a mixture of vinegar and water (1:1).
• 🌡️ Temperature difference:
  • The rubber of the brushes hardens in the cold or softens in the heat. Use winter wipers (with silicone coating) or store the car in the garage.
• 🔩 Lever wear:
  • Check the play in lever hinges - if there is one, the entire mechanism needs to be replaced (article no. 28510-4M000).
• 💧 Incorrect washer:
  • Liquids containing alcohol corrode rubber. Use only specialized washers (For example, Liqui Moly Scheiben-Frostschutz).

🔧 Emergency solution: If the squeak appears on the road, apply a wiper to the rubber silicone grease (spray WD-40 Specialist Silicone). This is a temporary measure - after 1-2 weeks the brushes will still have to be replaced.

What to do if the wipers “stick” to the glass?

This happens due to electrostatic discharge between rubber and glass. Solution: wipe the glass with an antistatic agent (for example, screen cleaner) or replace the brushes with graphite ones (for example, Bosch Graphite).

Diagnostics of wiper drive malfunctions

If the wipers are on Murano Z50 work jerkily, do not turn on or move asynchronously, the problem may be in the drive. Let's look at typical symptoms and their causes:

Symptom	Probable Cause	Solution
The wipers move jerkily	Wear reducer gears or motor bearing	Replacing the gear motor (article no. 28500-4M000)
One brush doesn't work	Break drive rods or breakdown lever	Traction diagnostics (article 28520-4M000), lever replacement
Wipers do not return to their original position	Crash limit switch or control unit	Reflashing the block or replacing the limit switch (28530-4M000)
Noise during operation	Wear lever bushings or lack of lubrication	Bushing lubrication (Litol-24) or their replacement

⚠️ Attention: On Murano Z50 with the system ProPILOT Assist (adaptive cruise control) wiper malfunctions can block the cameras! Before diagnosing, disable the system in the menu Settings → Driving assistants.

🔧 Self-check of the gearmotor:

1. Remove plastic protection under the hood (4 clips).
2. Disconnect power connector from the motor (white connector).
3. Serve 12V directly to contacts 1 (+) And 2 (–) - If the motor does not spin, replacement is required.

Frequently asked questions about wipers for Nissan Murano Z50

Is it possible to install wipers longer than standard ones?

No! Increasing the length of the brushes will lead to:

• 🚫 Geared motor overload (it is not designed for additional resistance).
• 🚫 Scratches on glass due to improper pressure distribution.
• 🚫 Error triggered in the system Auto Wipers.

Maximum permissible deviation: ±1 inch (25 mm).

How often should you change wipers on a Murano Z50?

The service life depends on the conditions:

• 🌞 Summer brushes: every 6–12 months (rubber is destroyed by UV rays).
• ❄️ Winter brushes: every 3–6 months (due to salt and reagents).
• 🚗 Signs of wear: stains, streaks, creaking, “bouncing” during operation.

Why doesn't the washer get on the glass?

Probable reasons:

• 🔧 Injectors clogged - clean with a needle or compressed air.
• 🔧 The direction of the jet is off — adjust the angle of the nozzles with a flat screwdriver.
• 🔧 Washer pump faulty (article 28370-4M000) — check the voltage at the connector.

💡 Lifehack: For fine adjustments, use laser level - the jet should hit 1/3 brush height.

What to do if the wipers are frozen to the glass?

Do not tear them off by force - this can damage the mechanism! Follow the steps:

1. Start the engine and turn on glass heating to the maximum.
2. Pour over ice warm (not hot!) water with the addition of salt (1 tbsp per 1 liter).
3. Carefully pry up the wipers plastic scraper, shaking them left and right.

⚠️ Do not use metal objects - they scratch the glass and damage the rubber of the brushes.

Is it possible to restore wiper rubber?

Partially yes. Methods:

• 🧴 Treatment with silicone grease (extends life by 1–2 months).
• 🔥 Heating with a hairdryer (softens hardened rubber, but temporarily).
• 📉 Sanding (granularity P1000) - removes burrs.

🔹 Important: These methods only work when small cracks. If the rubber is crumbled, just replace it.