Jabot for Nissan Terrano 3: a complete guide to selection, installation and operation

Nissan Terrano 3 (2014–2020) is a popular crossover, which in Russian realities is often used in difficult conditions: from city traffic jams to off-road conditions. One of the first elements to suffer from an aggressive environment is frill — a protective cover under the hood, covering the space between the windshield and the engine compartment. Its main task is to prevent dirt, water and debris from entering the interior through the ventilation openings, as well as to protect the windshield wipers and wiper mechanisms from premature wear.

However, over time, the frill loses elasticity, cracks or even breaks - this is especially true for cars older than 5 years. In this article we will look at how choose the right replacement (original vs analogues), which materials are preferable for the Russian climate, and we will give step-by-step installation instructions. We will also reveal The secret to extending the life of a frill using inexpensive products - a method that is used at service stations, but is rarely mentioned in open sources.

Why do you need a jabot on Nissan Terrano 3 and what problems does it solve?

Many owners Terrano 3 they underestimate the role of the frill, considering it only a decorative element. In fact this is critical part, affecting:

• 🌧️ Protection from water: Without a frill, rainwater and snow enter the air intakes, which leads to fogging of the windows and corrosion of the metal under the hood.
• 🍂 Preventing Clogging: leaves, dust and road dirt clog the drainage holes, causing moisture to accumulate in the cabin (especially true for cars with air conditioning).
• 🚿 Wiper lifespan: sand and small stones falling on the glass without protection scratch it and wear out the rubber blades of the wipers 2-3 times faster.
• 🔊 Noise insulation: Full frill reduces wind noise at speeds above 80 km/h.

On Terrano 3 frill also plays a role thermal insulation barrier. In summer, it prevents heating of the interior from the hot engine compartment, and in winter, it reduces heat loss through the windshield. On models with climate control, this helps save fuel because the system is less likely to operate at full power.

⚠️ Attention: If the frill is missing or damaged, check the condition of the drain pipes under the hood. Their clogging is the main reason for the appearance of water in the front passenger's feet.

Original vs analogues: which is better for Nissan Terrano 3

When choosing a frill on Terrano 3 (body R9M) owners are faced with a dilemma: to buy original part from Nissan (article 27060-JM00A) or analogues from third-party manufacturers. Let's look at the pros and cons of each option.

Criterion	Original frill	Analogs (for example, Febi, Hella)
Material	Soft thermoplastic elastomer (TPE), UV resistant	Hard plastic or rubber, can harden in the cold
Service life	5–7 years (with proper care)	2–4 years (depending on the manufacturer)
Price, rub.	4 500–6 000	1 200–2 500
Mount Compliance	Perfect fit, all clips and holes match	May require modifications (e.g. trimming edges)
Warranty	12 months (at official dealers)	Absent or 3–6 months

The original frill justifies its price if you plan to use the car for a long time. However, for budget repairs, analogues from trusted brands, such as Febi Bilstein (article 27060) or Hella (article 8XH 355 109-121). The main thing is to pay attention to material flexibility: if the part is too hard, it will quickly crack in the cold.

How to choose a frill by size and material: 5 key parameters

Even if you settled on the original, it is important to make sure that the part is suitable for your modification Terrano 3. Here's what to look for:

1. Year of manufacture: The frill for restyled models (2017–2020) may differ in the shape of the fasteners from the pre-restyling model (2014–2016).
2. Equipment: Machines with LED optics have a different configuration of holes for wires.
3. Color: The original only comes in black (Black), but some analogues offer gray (Gray) to mask dirt.
4. Availability of seal: High-quality frills have rubber edging around the edges for a snug fit.
5. Manufacturer: Check reviews for a specific model - for example, frill from Febi often praised for its durability, and Sasic - for a low price.

When purchasing a used frill, inspect it for microcracks (especially in the places where the clips are attached) and check the flexibility: if the plastic breaks when bent, the part will not last more than a season. Also note hole for washer — it must exactly match your model, otherwise you will have to modify it.

Step-by-step instructions for replacing the frill with Nissan Terrano 3

Installing a new frill does not require special skills, but it will require care. The whole process will take 30–40 minutes. Here's what you'll need:

• 🔧 Flathead screwdriver or plastic clip remover
• 🧴 Silicone grease (for example, Liqui Moly Silicon-Spray)
• 🧼 Plastic cleaner (for example, Sonax Plastic Cleaner)
• 🔦 Flashlight (for inspecting fasteners)

Step 1. Dismantling the old frill

1. Open the hood and lock it.
2. Remove the wipers (unscrew the nuts with a wrench 13 mm and slide them off the shaft).
3. Using a flat-head screwdriver, pry up the frill fastening clips (there are 6–8 of them) and carefully pull them out. Do not pull the frill by force - so you will break the latches!
4. Disconnect the washer hose (if it is attached to the frill).

Step 2. Preparing a new frill

Before installation, treat the rubber seal of the new frill with silicone grease - this will facilitate installation and extend its service life. Also check that the holes for the washer and the wires match (if necessary, carefully widen them with a knife).

Step 3: Installation

1. Slide the frill into place, starting on the driver's side.
2. Snap the clips into place, starting from the center ones and moving towards the edges.
3. Connect the washer hose and check its operation.
4. Reinstall the wipers and adjust their position.

⚠️ Attention: If after installation the frill does not fit tightly to the glass, check whether the metal latches on the body are bent. They can be straightened with pliers.

Caring for a frill: how to extend its life by 2 times

Average service life of frill Terrano 3 - 3–5 years, but with proper care this period can be increased to 7–8 years. Here 4 key rules:

• 🧴 Regular cleaning: Wash the frill once a month with a soft brush and car shampoo. Avoid harsh detergents (eg Kärcher with high pressure) - they destroy the protective layer of plastic.
• ☀️ UV protection: Apply to frill polish for plastic (For example, Turtle Wax Plastic Polish) every 3 months. This will prevent cracking.
• ❄️ Winter preparation: Treat the seal before frost silicone greaseso that he doesn't tan. Also check the drainage holes under the frill - they should not be clogged with ice.
• 🚗 Parking: Try not to park your car under trees - falling branches and sap will damage the plastic.

Secret from service station masters: To prevent the frill from cracking at the joints, coat them once a year liquid rubber (For example, Abro Black Flex Seal). This creates an elastic protective layer that prevents tearing due to vibration.

What to do if the frill is already cracked?

If the crack is small (up to 2 cm), it can be repaired epoxy glue for plastic (eg 3M Scotch-Weld). For major damage, it is better to buy a new frill - the repair will not last long.

Top 3 mistakes when choosing and installing frills

Even experienced car owners sometimes make mistakes that lead to rapid wear of the frill or problems with the interior. Here are the most common:

1. Buying a frill without a seal. Cheap analogues often come without rubber edging, which leaves a gap between the frill and the glass. This leads to water leaks into the cabin and fogging of windows.
2. Ignoring clips. Many people save money and use old latches, but they often break during dismantling. New clips cost a penny (about 50 rubles apiece), but without them the frill will rattle on bumps.
3. Incorrect fixation of the washer hose. If the hose is pinched or twisted, the liquid will not flow onto the glass, and in cold weather this will lead to tube rupture.

Another common mistake is installing frill without checking drainage. Under the hood Terrano 3 There are two drainage holes (on the sides of the frill) that often become clogged with leaves. If they are not cleaned, water will accumulate under the frill and rust the metal.

Where to buy jabot on Nissan Terrano 3: proven options

Prices for frills vary from 1,200 to 6,000 rubles, depending on the type and place of purchase. Here's where to look:

Source	Pros	Cons	Average price, rub.
Official dealer Nissan	12 month warranty, original part	Expensive, long wait (if out of stock)	5 500–6 000
Online stores (Exist.ru, Autodoc)	Fast delivery, wide selection of analogues	Risk of running into a fake	1 500–3 500
Showdown	Low price (can be found for 800–1,200 rubles)	No guarantee, condition is “depending on luck”	800–1 500
Local auto-analysis	You can inspect the item before purchasing	Limited assortment	1 000–2 000

When purchasing online, be sure to check seller reviews and ask for a photo of the actual item. On Exist.ru And Autodoc often come across counterfeits of the brand Febi — differ in paler plastic and the absence of a logo on the back side.

If you buy a used frill, pay attention to:

• 🔍 Condition of the clips - they must not be broken or deformed.
• 🌡️ Flexibility of plastic - if the part is fragile, it will crack on the first frosty night.
• 💧 Traces of sealant - this is a sign that the frill has already been repaired.

FAQ: Frequently asked questions about frills Nissan Terrano 3

Is it possible to drive without a frill?

Technically, yes, but this will lead to rapid wear of the wipers, fogging of the windows and dirt entering the cabin through the air intakes. In the long term, the absence of a frill accelerates corrosion of the metal under the hood.

What sealant should I use to repair cracks?

Suitable for plastic 3M Scotch-Weld DP8005 (two-component epoxy adhesive) or Loctite Plastics Bonding System. Important: Clean the surface before gluing. degreaser and sand the edges of the crack.

Why does the new frill rattle on bumps?

Most likely, not all the clips are latched or the metal latches on the body are bent. Also check if the frill is touching the wipers - sometimes they rub against the plastic during operation.

Is it possible to paint the frill in the body color?

Yes, but only special paint for plastic (For example, Motip Plastik Lack). Regular car enamel will peel off quickly. Plastic must be treated before painting adhesive primer.

How often should the frill be changed?

With careful use - once every 5–7 years. If the car is often driven off-road or parked outdoors, replacement will have to be done every 3-4 years.