Automatic transmission Nissan Qashqai - a complex unit that requires regular maintenance. Many owners mistakenly believe that the automatic transmission oil does not need to be changed, but neglect of this procedure leads to expensive repairs after 150-200 thousand km. In this article we will look at when and how to change the oil in the box. Kashkaya (models J10 And J11), what tools will be needed, and what mistakes are most often made when replacing them yourself.
The manufacturer states that the oil in the automatic transmission RE0F10A (installed on most Qashqai with motors 1.6, 2.0 And 1.5 dCi) is designed for the entire service life. However, in practice after 90-100 thousand km it loses up to 30% of its lubricating properties, which leads to increased wear of clutches and solenoids. If you notice jerks when switching, delays or extraneous noise, this is the first signal for diagnosis.
When to change the oil in a Nissan Qashqai automatic transmission: signs and regulations
Official regulations Nissan does not provide for changing the oil in the automatic transmission, but the experience of service station technicians and owners shows the opposite. Optimal intervals:
- 🔧 Partial replacement (30-40% volume) - every 50-60 thousand km or once every 3-4 years. Suitable for prevention.
- 🔄 Complete replacement (hardware or manual) - every 90-100 thousand km. Required when purchasing a used car.
- ⚠️ Emergency replacement - when metal shavings appear on the dipstick, a burnt smell or errors
P0730-P0740.
Signs that it's time to change the oil:
- 🔴 Jerks or slipping when changing gears (especially when cold).
- 🔴 Delays when switching from 1st to 2nd gear.
- 🔴 There was a hum or vibration in the area of the automatic transmission selector.
- 🔴 Darkening of the oil on the dipstick (should be reddish, not black).
⚠️ Attention: If silvery dust (chips) is visible on the automatic transmission dipstick, this is a sign of wear on the planetary mechanism. In this case, changing the oil can only temporarily delay the repair - diagnostics at a service station with disassembly of the box are required.
For models Qashqai J11 (2014+) with CVT JF016E the rules are different: the oil is changed every 60 thousand km no options, since the variator is more sensitive to the quality of the lubricant. Read more about CVTs in our separate article.
- Every 50 thousand km
- Every 90 thousand km
- Only when problems arise
- Never changed
- I don't know
What kind of oil to fill in the automatic transmission of Nissan Qashqai: original vs analogues
The manufacturer recommends using only original oil Nissan Matic Fluid S (article KE908-99932) for boxes RE0F10A And RE0F10D. However, there are worthy analogues on the market that meet the specifications JWS 3309:
| Manufacturer | Oil name | Article | Price for 1 l (2026) | Notes |
|---|---|---|---|---|
| Nissan | Matic Fluid S | KE908-99932 | 1 200–1 500 ₽ | Original, best choice |
| Mobil | ATF 3309 | 153976 | 900–1 100 ₽ | Complete analogue, often used in service stations |
| Idemitsu | ATF Type J | 30450055-001 | 850–1 000 ₽ | Japanese quality, suitable for cold climates |
| Ravenol | ATF JWS 3309 | 4014835715317 | 1 000–1 300 ₽ | German brand, high temperature stability |
Oil volume to change:
- 🔧 Partial replacement — 3.5–4 liters (~30-40% of the total volume is drained).
- 🔄 Complete replacement — 7–8 liters (for a device) or 9–10 liters (for manual washing).
⚠️ Attention: Never mix oils from different manufacturers! If it was previously flooded Matic Fluid S, and you decided to switch to Mobil ATF 3309, a complete replacement with flushing is required. Otherwise, there may be problems with the operation of the solenoids.
For CVTs JF016E (installed on Qashqai J11 with motors 1.2 DIG-T And 1.6 dCi) is used special oil Nissan CVT Fluid NS-3 (article KLE52-00004). Replacement is required strictly every 60 thousand km!
Before purchasing oil, check its authenticity! Original Nissan Matic Fluid S has a holographic sticker on the canister and a clear barcode. Counterfeits are often sold in cans without a bottling date.
Tools and consumables for changing automatic transmission oil
To change the automatic transmission oil yourself Nissan Qashqai you will need:
New oil (4–10 l depending on the type of replacement)|New automatic transmission oil filter (part number 31726-1XF0A)|Pan gasket (part number 31397-1XF0A)|10 mm square wrench for drain plug|10 and 14 mm socket for pan bolts|Funnel with extension for filling oil|Drain container (minimum 5 l)|Gloves and rags|Torque wrench (optional, for proper tightening of bolts)-->
Additionally you may need:
- 🔧 Flushing fluid (For example, Liqui Moly ATF Reiniger) - if a complete replacement is planned.
- 🔧 New dipstick (article 31397-1XF00) - if the old one is damaged.
- 🔧 Sealant (For example, Loctite 574) - for processing the pallet gasket.
Cost of consumables (2026):
- 💰 Automatic transmission filter — 1,200–1,800 ₽.
- 💰 Pallet gasket - 500–800 ₽.
- 💰 Oil (4 l) - 4,000–6,000 ₽ (depending on the brand).
⚠️ Attention: Do not use filters or gaskets from other models Nissan! For example, a filter from X-Trail T31 looks similar, but has a different throughput, which can lead to oil starvation of the automatic transmission.
If you are planning a complete replacement with flushing, you will additionally need:
- 🔧 Oil change machine (can be rented at a service station).
- 🔧 Hoses and adapters for connection to the automatic transmission cooling system.
How to check the oil level in a Qashqai automatic transmission?
1. Warm up the box to 60–70°C (drive 10–15 km).
2. Place the car on a flat surface with the engine running at idle.
3. Remove the automatic transmission dipstick (located to the right of the engine, under the hood), wipe it and insert it back.
4. Take out the dipstick again - the level should be between the marks HOT (hot).
5. If the oil is below the minimum, add through the filler neck (use a funnel).
Step-by-step instructions: partial oil change in automatic transmission
Partial replacement is suitable for prevention and is carried out without removing the pan. Step by step process:
Step 1. Preparation
Drive the car into a pit or overpass. Start the engine and warm up the gearbox to operating temperature (60–70°C). This is necessary so that the oil becomes less viscous and drains better. Stop the engine.
Step 2. Drain the old oil
- Remove the crankcase protection (if equipped).
- Place a container under the automatic transmission drain plug (it is located on the tray, closer to the back of the box).
- Using a 10 mm wrench, unscrew the drain plug. Be careful - the oil will be hot!
- Wait until the oil has completely drained (usually 10–15 minutes).
Step 3: Replace the filter and gasket
For a partial replacement, the filter and gasket do not need to be changed (if the oil is not very dirty). However, if the mileage is more than 100 thousand km, it is recommended:
- Unscrew the pan bolts (10 mm head).
- Remove the pan and drain the remaining oil.
- Replace the filter (part number 31726-1XF0A) and gasket (part number 31397-1XF0A).
- Clean the pan of old sealant and metal shavings (use solvent).
Step 4. Filling with new oil
- Reinstall the pan and tighten the drain plug (tightening torque: 35–40 Nm).
- Insert a funnel into the filler neck (located next to the dipstick).
- Fill with new oil (3.5–4 liters).
- Start the engine and warm up the transmission. Check the level on the dipstick and add if necessary.
With a partial replacement, only 30–40% of the oil is renewed. A complete update requires 2-3 such procedures at intervals of 500-1000 km.
Complete automatic transmission oil change: hardware and manual methods
Complete automatic transmission oil change Nissan Qashqai can be done in two ways:
- 🔧 Hardware method - using a special stand that replaces old oil with new oil under pressure.
- 🔧 Manual method — multiple drain-fill with washing (requires more time and oil).
Hardware replacement (recommended for service stations):
- Connect the hoses of the device to the automatic transmission cooling radiator pipes.
- Start the engine and turn on the device. It will pump new oil, displacing the old one.
- Control the color of the oil at the exit - the procedure is completed when it becomes light.
- Replace the filter and pan gasket.
- Check the level and top up if necessary.
Manual complete replacement (for doing it yourself):
- Perform partial replacement (as described above).
- Drive 500–1000 km for the new oil to mix with the old.
- Repeat draining and filling 2-3 more times. By the third time the oil will be almost clean.
⚠️ Attention: When replacing hardware, there is a risk of washing out deposits that can clog the solenoids. If the car's mileage is more than 150 thousand km, it is better to use the manual method or combine both approaches.
Cost of a complete replacement at a service station:
- 💰 Hardware replacement — 4,000–6,000 ₽ (excluding oil).
- 💰 Manual replacement — 2,500–4,000 ₽ (depending on the region).
Typical mistakes when changing the oil in a Qashqai automatic transmission
Even experienced car owners make mistakes that can lead to box failure. Let's look at the most common ones:
1. Incorrect oil level
- ❌ Overflow — leads to foaming of the oil and loss of lubricating properties.
- ❌ Underfilling — causes oil starvation and accelerated wear of friction clutches.
✅ How to avoid: Always check the level on a warm box (60–70°C) using the dipstick. Add in small portions (100 ml).
2. Using the wrong oil
Replacement Matic Fluid S to universal Dexron III or ATF+4 will lead to:
- 🔴 Sticking solenoids.
- 🔴 Increased wear of the torque converter.
- 🔴 Jerks when changing gears.
3. Untimely filter replacement
The automatic transmission filter becomes clogged with metal shavings and wear products. If it is not changed when changing the oil, new particles will quickly contaminate the fresh oil. The recommended filter replacement interval is every 90–100 thousand km.
4. Ignoring rinsing the pan
Metal shavings and deposits accumulate at the bottom of the pan. If you don't clean the pan when changing the oil, dirt will fall back into the box. Use solvent and a magnet to collect the chips.
5. Tightening the pan bolts without a torque wrench
Tightening too tightly leads to deformation of the pan, while tightening too weakly leads to oil leakage. Tightening torque for automatic transmission pan bolts Qashqai — 8–10 Nm.
If after changing the oil there are jerks when switching, it is possible that too much new oil has entered the box (it is more viscous than the old one). In this case, perform a partial drain (0.5–1 l) and check the operation of the automatic transmission.
What to do after changing the oil: adaptation and break-in
After changing the automatic transmission oil Nissan Qashqai There are several important steps required:
1. Box adaptation
Modern automatic transmissions RE0F10A And RE0F10D have an adaptive gear shift program. After changing the oil, you need to reset it:
- Disconnect the battery terminal for 10-15 minutes (this will reset the adaptive settings).
- Reconnect the battery and start the engine.
- Let the box “learn” - drive 50–100 km in a gentle mode (without sudden acceleration).
2. Checking the operation of the automatic transmission
After changing the oil, pay attention to:
- 🔹 Smooth gear shifting (there should be no jerks or delays).
- 🔹 No extraneous noise (hum, grinding).
- 🔹 The indicators on the dashboard are correct (the warning should not be on
AT).
3. Oil level control
1-2 days after replacement, check the oil level again. Top up if necessary. If the level has dropped significantly (more than 0.5 l), check the tightness of the pan and drain plug.
⚠️ Attention: If errors appear after changing the oilP0730(“Wrong gear ratio”) orP0740(“Torque Converter Lockup Malfunction”), this may indicate:
- 🔴 Incorrect oil level.
- 🔴 Clogged solenoids (if the oil has not been changed for a long time).
- 🔴 Poor quality oil or filter.
In this case, it is recommended to contact a service station for diagnostics.
FAQ: Frequently asked questions about changing the oil in the Nissan Qashqai automatic transmission
Is it possible to change the oil in a Qashqai automatic transmission yourself or is it better to go to a service station?
You can perform a partial oil change yourself if there is a hole or overpass. A complete replacement (especially hardware) requires special equipment and is best left to professionals. If you have never repaired an automatic transmission, we recommend starting with a partial replacement or contacting a service station.
How much does it cost to change the oil in a Qashqai automatic transmission at a service station in 2026?
The cost depends on the type of replacement and region:
- 💰 Partial replacement — 1,500–2,500 ₽ (excluding oil).
- 💰 Complete hardware replacement — 4,000–6,000 ₽.
- 💰 Complete manual replacement (3 stages) - 3,000–5,000 ₽.
The oil will cost 4,000–8,000 rubles (depending on the volume and brand).
What happens if you don’t change the oil in your Qashqai automatic transmission?
The consequences depend on the mileage:
- 🔴 100–150 thousand km - deterioration in smoothness of switching, increased wear of clutches.
- 🔴 150–200 thousand km - slippage, errors
P0730-P0740, wear of solenoids. - 🔴 200+ thousand km — breakdown of the torque converter, jamming of the planetary mechanism (repair will cost 80,000–150,000 rubles).
What kind of oil should I fill in the Qashqai 2.0 (gasoline) and 1.5 dCi (diesel) automatic transmission?
Both engines use the same oil - Nissan Matic Fluid S (KE908-99932) or its analogues (Mobil ATF 3309, Idemitsu Type J). Exception: models with CVT JF016E (For example, Qashqai J11 1.2 DIG-T), where required Nissan CVT Fluid NS-3.
Is it necessary to flush the automatic transmission when changing the oil?
Flushing is required in the following cases:
- 🔹 The oil has turned very black or has a burnt smell.
- 🔹 A lot of metal shavings were found in the pallet.
- 🔹 Car mileage is more than 150 thousand km.
For flushing, use special liquids (for example, Liqui Moly ATF Reiniger) or the multiple drain-fill method.