Burnt out brake light bulb Nissan Almera G15 - a problem that many owners prefer to solve on their own. And for good reason: the procedure takes 10-15 minutes, does not require special tools and allows you to save on a service center. However, even in such a simple operation there are nuances: from choosing the right lamp to carefully removing the lampshade so as not to break the latches.
In this article we will look at all stages of replacement - from fault diagnosis to performance testing. You will find out which lamps are suitable for Almera G15 (2013-2018), how to avoid common mistakes when disassembling a flashlight and what to do if, after replacement, the brake light still does not work. And for those who are afraid of damaging the plastic, we have prepared a unique life hack using a paper clip to safely remove the cartridge.
How can you tell if your brake light bulb is burned out?
The first sign of trouble is warning on the dashboard in the form of a light bulb icon with an exclamation mark. However, on Nissan Almera G15 This indicator does not always light up, especially if only one of the two lamps has burned out. Therefore, it is important to visually check your brake lights at least once a month.
Other symptoms:
- 🔴 The brake light does not light up when you press the brake pedal (visible in the reflection or with the help of a second person).
- 💡 The lamp flashes or shines dimly - this is a sign of imminent failure.
- 🚨 There is an error on the tidy
Bulb Failure(if the car is equipped with a lamp control system).
You can check the functionality yourself:
- Put the car on the handbrake and turn on the ignition.
- Press the brake pedal and walk around the back of the car.
- If one of the lamps does not light, that is the problem. If both do not light, check the fuse
F30 (10A)in the mounting block.
⚠️ Attention: On Almera G15 brake lights and clearances are used different lamps, but located in the same block. If only the indicator light does not light up, the lamp needs to be changed.W5W, notP21/5W.
- Once a month
- Only when the error comes on
- Before long trips
- Never checked
Which lamps are suitable for Nissan Almera G15?
At the brake lights Nissan Almera G15 (2013-2018) are installed double filament lamps type P21/5W (base BAY15d). They combine the function of a brake light (21 W) and a side light (5 W). When purchasing, pay attention to:
- 🔹 Manufacturer: Optimal choice - Osram, Philips or Bosch. Cheap Chinese analogues often burn out after 2-3 months.
- 🔹 Lamp type: For Almera G15 only suitable
P21/5W, notP21W(single-strand). - 🔹 Glow color: Standard - transparent lamps. Red or blue are prohibited by traffic rules.
| Lamp type | Power | Base | Application | Article (example) |
|---|---|---|---|---|
P21/5W |
21W / 5W | BAY15d | Brake light + clearance | Osram 2825 |
W5W |
5W | W2.1x9.5d | Side light | Philips 12961 |
PY21W |
21W | BAU15s | Reverse | Bosch 1987302046 |
If you want to install led lamps, choose models with a snag for the CAN bus (for example, Philips LED X-tremeUltinon). Without it, an error will appear on the device. Also note that LED lamps may require polarity reversal - on Almera G15 The minus goes to the base, and the plus goes to the central contact.
Before purchasing a lamp, check its performance directly in the store using a tester. Many auto parts sellers provide this service free of charge.
Preparing for replacement: tools and safety precautions
To replace the brake light bulb with Nissan Almera G15 you will need:
- 🔧 Flat screwdriver (for prying latches).
- 🧤 Cotton gloves (so as not to leave greasy marks on the glass of the lantern).
- 💡 New lamp
P21/5W. - 🔦 Flashlight or phone with backlight (lighting in the trunk is weak).
Security measures:
- ⚡ Turn off the ignition and remove the terminal from the battery (negative). This will prevent a short circuit from accidentally touching the contacts.
- 🚗 Place the car on a flat surface and turn on the handbrake.
- 👓 If you work in the cold season, warm up the interior - plastic latches become fragile in the cold.
⚠️ Attention: Do not touch the glass bulb of a halogen lamp with your bare hands! Fatty traces lead to local overheating and shorten the life of the lamp. Use gloves or a cloth.
Disconnect the battery|Open the trunk and put things away|Prepare tools|Put on gloves-->
Step-by-step instructions: how to change a brake light bulb
The replacement process is the same for both headlights, but it’s more convenient to start with right side (in the direction of travel), since there is more space for maneuvers. Follow the instructions:
Step 1: Removing the trunk trim
Open the trunk and locate the plastic cover that covers access to the headlight. It is attached to two clips (above and below). Carefully pry it off with a flat-head screwdriver, starting from the bottom corner. Pull towards yourself with even force so as not to break the latches.
Step 2: Accessing the Lamp Socket
After removing the trim you will see the back of the canopy with three cartridges:
- 🔴 Upper - brake light/marker (
P21/5W). - 🟡 Middle - turn signal (
PY21W). - ⚪ Bottom - reverse (
W16W).
Do you need upper chuck. Turn it counterclockwise 30-45 degrees and pull it out.
Step 3: Replacing the lamp
Remove the old lamp from the socket by lightly pressing it and turning it to the left. Install a new lamp P21/5W, aligning the protrusions on the base with the grooves in the cartridge. Important: on Almera G15 the lamp is installed in only one position - the wide contact must be on top.
Step 4. Assembly
Insert the socket back into the flashlight and turn clockwise until it clicks. Make sure the lamp is not loose. Install the trunk trim by pressing the clips until you hear a characteristic click.
Repeat the procedure for the second headlight if necessary.
What to do if the chuck does not turn?
If the chuck is jammed, do not apply force as this will break the plastic guides. Take a paper clip, straighten it and carefully pry the cartridge from the side while turning it counterclockwise. Often this helps get it off the ground.
Common mistakes and how to avoid them
Even with a simple procedure, owners Nissan Almera G15 make mistakes that lead to repeated replacement or damage to the flashlight. Let's look at the most common ones:
1. Installing the wrong type of lamp
If you put P21W instead of P21/5W, the side light will not work. Lamps with bases are also not suitable BA15s - they are not fixed in the cartridge.
2. Reversed polarity of LED lamps
LED lamps are polarity sensitive. If after installation they do not light up, remove the lamp, rotate it 180 degrees and insert it back.
3. Damage to the rubber seal
When removing the socket, do not pull on the wires - this can tear the seal, which will lead to moisture getting into the lamp. If the elastic is torn, replace it (part number for Almera G15 — 265B0-4M000).
4. Loose trunk trim
If the clips do not snap fully into place, the skin will rattle on bumps. Check the fastening by pressing the cover around the perimeter.
⚠️ Attention: After replacing the bulb, turn on the ignition and check the brake light without closing the trunk. If the lamp does not light, but the contacts are clean, the problem may be lighting control unit (located under the steering wheel).
If after replacement the lamp burns out again after a short time, check the voltage in the on-board network. The norm is 13.8–14.4 V. Exceeding even by 0.5 V reduces the service life of the lamps by 2–3 times.
What should I do if the brake light does not work after replacement?
If the new lamp does not light up, check sequentially:
1. Fuse
On Nissan Almera G15 The fuse is responsible for the brake lights F30 (10A) in the mounting block (located to the left of the steering wheel, under the cover). Take it out and check it visually or with a multimeter. If it is burnt out, replace it with a similar one.
2. Contacts in the socket
Oxidized or burnt contacts are a common cause of malfunction. Clean them with fine sandpaper or WD-40. If the contacts are melted, the cartridge must be replaced (part number - 26150-4M000).
3. Wiring
Test the wires going to the socket with a tester:
- 🔴 Red/yellow - plus brake light.
- 🟢 Green/white - plus size.
- ⚫ Black - minus (mass).
If there is no voltage, the problem is in the wiring or control unit.
4. Brake light switch
Located under the brake pedal. When you press the pedal, it should close the contacts. Check it with a multimeter or replace it (part number - 40520-4M000).
How much does a service replacement cost and when should you contact a professional?
If you are not confident in your abilities or encounter one of the problems below, it is better to contact the service:
- 🔧 The cartridge or wiring is damaged.
- 💡 Lamps burn out more often than once every 6 months.
- ⚡ There is an error on the tidy
Bulb Failure, but the lamps are working. - 🔌 The entire rear light does not work (neither the brake light, nor the parking light, nor the turn signal are on).
Cost to replace brake light bulb Nissan Almera G15 in the service:
| Type of work | Cost (RUB) | Time |
|---|---|---|
| Replacing one lamp | 300–500 | 10–15 min |
| Electrical diagnostics (without repair) | 800–1200 | 30–40 min |
| Replacing the cartridge or wiring | 1500–2500 | 1–2 hours |
Replacing it yourself will only cost the cost of the lamp (150–400 rub. for Osram/Philips). However, if the problem lies in the electrical equipment, the savings may result in more expensive repairs.
FAQ: Frequently asked questions about replacing the brake light bulb
Is it possible to replace the brake light bulb without removing the light?
Yes, on Nissan Almera G15 replacement is carried out through the trunk. There is no need to remove the flashlight - just remove the casing and pull out the socket.
What is the service life of brake light bulbs?
Standard halogen lamps P21/5W serve 500–1000 hours (about 2–3 years with average intensity of use). LED - up to 50,000 hours, but may require snags for the CAN bus.
What happens if you drive with a broken brake light?
This is a violation Traffic rules 12.5 (malfunction of external lighting devices). Fine - 500 rub. or warning. In addition, it is dangerous: the driver behind may not notice the braking.
Is it possible to install LED lamps instead of halogen ones?
Yes, but keep in mind:
- 🔹 You need a decoy for the CAN bus (otherwise an error will appear).
- 🔹 LED lamps must be with the correct polarity (on Almera G15 minus on the base).
- 🔹 Brightness should not exceed
3000 K(white light is prohibited).
Where to buy original lamps for Almera G15?
Original lamps Nissan (article 26100-4M000) can be ordered from official dealers or trusted online stores:
The cost of the original lamp is approx. 400–600 rub., but its characteristics are no different from Osram or Philips.