Car owners Nissan sooner or later they are faced with the need to reset the odometer readings - be it daily mileage (Trip A/B) or total mileage. Button Trip Reset (or TRIP/RESET) is responsible for this function, but its location and operating principles vary depending on the model and year of manufacture. In some cases, resetting the mileage turns into a real puzzle: the button does not respond, the readings are reset spontaneously or, conversely, freeze at one value.

In this article we will analyze all official and undocumented ways to reset mileage on a Nissan, including instructions for analog and digital instrument panels, and also consider typical faults - from oxidized contacts to software failures of the unit BCM. We will pay special attention to the models Qashqai J11, X-Trail T32 And Juke F15, where is the logic of the button operation Trip Reset has its own nuances.

Where is the Trip Reset button on Nissan: location by model

Mileage reset button Nissan can be done in the form:

  • 🔘 Mechanical key on the dashboard (most often to the right of the speedometer).
  • 🔄 Touch zone on the steering wheel switch (on models with digital instrument panel, e.g. Ariya or Leaf).
  • 📱 Virtual button in the on-board computer menu (relevant for Navara NP300 2020+).

The exact location depends on the generation and configuration. Below is a table with the most common options:

Model Nissan Years of manufacture Trip Reset button location Panel type
Qashqai J10/J11 2007–2021 To the right of the speedometer, under the dashboard glass Analogue/Hybrid
X-Trail T31/T32 2007–2022 On the steering column switch (left lever, button TRIP) Digital/analogue
Juke F15/F16 2010–2023 On the front side of the panel, next to the button MODE Digital (TFT)
Navara D40/NP300 2005–2026 In the on-board computer menu (INFO → Trip Meter → Reset) Digital (4.2" display)

On models with fully digital panel (For example, Ariya or Leaf e+) there may not be a physical button at all. Instead, the reset is carried out through the touch menu on the steering wheel or voice commands (if supported NissanConnect).

📊 What type of dashboard does your Nissan have?
  • Analog (arrows)
  • Hybrid (arrows + screen)
  • Fully digital (TFT/LCD)
  • I don't know

How to reset daily mileage (Trip A/B) on Nissan: step-by-step instructions

Daily mileage (Trip A And Trip B) is the easiest to reset. The algorithm of actions depends on the type of button:

  1. On models with mechanical button (For example, Qashqai J11):

    • 🔘 Press and hold the button TRIP/RESET (usually 2-3 seconds).
    • 🔄 Indications Trip A will reset to zero. To reset Trip B first switch between modes with the button MODE.

  2. On models with steering column switch (X-Trail T32, Pathfinder R52):

    • 🔘 Briefly press the button TRIP on the left lever behind the wheel to switch between Trip A/B.
    • 🔄Hold the same button for 3 seconds to reset.

  • On models with digital panel (Navara NP300, Ariya):

    1. Нажмите кнопку INFO на руле.

    2. Выберите Trip Meter → Trip A или Trip B.
    

    3. Удерживайте OK/RESET до сброса.

    • Turn off the engine (on some models, reset is only possible with the ignition off)

    Make sure the car is on a level surface (for correct sensor calibration)

    Check that the button TRIP/RESET not stuck and can be pressed freely

    If the reset does not occur, try holding the button longer (up to 5 seconds) -->

    ⚠️ Attention: On some models (for example, Patrol Y62) reset Trip B is blocked if the car is moving at a speed higher than 5 km/h. This is done to prevent accidental data reset during a trip.

    Is it possible to reset the total mileage on a Nissan: myths and reality

    Reset question total mileage (odometer) is one of the most controversial. According to the legislation of most countries (including the Russian Federation), any tampering with the odometer reading is considered fraud and is punishable by fines or criminal liability. However, the network is full of proposals for “rewinding” the mileage using:

    • 🔧 Software scanners (For example, Launch X431 or Autel).
    • 💻 Block firmware BCM (requires soldering and access to Eeprom).
    • 🔌 Hardware emulators (connected to the CAN bus).

    Technically a reset is possible, but:

    ⚠️ Attention: Modern Nissan (2018 and newer) are equipped with mileage roll protection. Data on total mileage is duplicated in several blocks (BCM, ECM, ABS), and their inconsistency can lead to:
    • 🚨 Activation errors U1000 (data mismatch between modules).
    • 🔴 Engine start blocking (on models with Nissan Intelligent Key).
    • 📉 Loss of warranty (even if the reset was performed “for testing”).
    What happens if you change the mileage before selling?

    In addition to legal risks (Article 159.1 of the Criminal Code of the Russian Federation - fraud), the buyer can easily detect twisting through:

    1. **Diagnostic scanner** (checking blocks ECM/TCM).

    2. **Service history** (official dealers Nissan mileage is recorded at each maintenance).

    3. **Wear of parts** (brake discs, interior, suspension correspond to the mileage, not the odometer).

    4. **Online databases** (for example, Autocode or CarVertical store mileage history by VIN).

    If you really need to reset your mileage for a valid reason (for example, after replacing the dashboard), contact official service Nissan. Employees can perform odometer recalibration with recording of data in the service book.

    Trip Reset button does not work: reasons and repair methods

    If the button TRIP/RESET does not respond to clicks, the problem may lie in:

    Symptom Probable Cause Remedy
    The button cannot be pressed or fails Mechanical wear or breakage of the microswitch Replacing a button (article number, for example, 28510-4M000 for Qashqai J11)
    The button is pressed, but the reset does not occur Oxidation of contacts on the dashboard board Cleaning contacts with alcohol or Contact Cleaner
    The reset occurs spontaneously Circuit short circuit or fault BCM Diagnostics with a multimeter, flashing BCM
    The button works, but only on Trip A Software failure or odometer memory corruption Resetting the on-board computer settings (disconnecting the battery for 10 minutes)

    To diagnose mechanical problems:

    1. Remove the dashboard trim (usually clip-on).
    2. Check the integrity of the wires going to the button TRIP/RESET.
    3. Measure the resistance of the button when pressed/released (should be 0 ohm/∞).
    💡

    If the button TRIP/RESET sticks due to liquid ingress, do not rush to change it. Try rinsing with isopropyl alcohol (70%+) and drying with a hairdryer on the lowest setting. In 60% of cases this restores functionality.

    On models with digital panel (For example, Ariya) the problem may be due to a firmware failure. In this case it will help:

    1. Отключите аккумулятор на 15 минут.

    2. Подключите сканер (например, Launch CReader).
    

    3. Выполните команду BCM Relearn (обучение блока кузова).

    Features of mileage reset on popular Nissan models

    Some models Nissan have unique nuances of working with the button TRIP/RESET. Let's look at the most common ones:

    Nissan Qashqai J11 (2014–2021)

    On this model the button is located under the dashboard glass right. Features:

    • 🔄 To reset Trip B first click MODEto switch between modes.
    • 🚗 If after resetting the readings reset to zero on their own, check fuse F30 (10A) in the salon block.

    Nissan X-Trail T32 (2014–2022)

    Here the button is placed on left steering column switch. Important:

    • 🔋 Reset is only possible when ignition on (position ON, but not START).
    • 📶 If the button does not work, check CAN bus for errors (code U1000).

    Nissan Juke F15 (2010–2019)

    On Juke button integrated into touchpad to the right of the speedometer. A common problem is false positives due to static electricity. Solution:

    • 🧴 Wipe the panel with an antistatic agent (for example, Sonax).
    • 🔌 Update the firmware of the on-board computer (relevant for restyled versions 2017+).
    💡

    On models with the system NissanConnect (For example, Ariya or Leaf) mileage reset may require confirmation via the mobile application. Without synchronization with a smartphone, the function will be blocked.

    Common mistakes when resetting mileage and how to avoid them

    Even experienced drivers sometimes make mistakes when working with a button. TRIP/RESET. Here are the most common:

    1. Reset when moving. On many models (for example, Patrol or Navara) the button is blocked at higher speeds 5 km/h.Attempt to reset while driving may cause the odometer to freeze or display an error -- ----.

    2. Ignoring the order of actions. On X-Trail T31 first you need to switch to Trip A/B button MODE, and only then hold RESET.

    3. Using non-original buttons. Cheap analogues (for example, with AliExpress) may not match in resistance, which leads to failures of the on-board computer.

    ⚠️ Attention: On hybrid models (Nissan Note e-Power) reset mileage in mode EV (electric motor) may cause an error P0A7F (inconsistency of energy consumption data). Before resetting, switch to HEV.

    If after the reset the symbols appear on the panel ------ or EEE, this indicates:

    • 🔋 Lost connection with the unit ECM (check fuse F10).
    • 💾 Odometer memory corruption (reflashing required).

    Alternative ways to reset mileage without the Trip Reset button

    If the button is broken or missing (for example, on some versions Nissan Almera Tino), you can use alternative methods:

    1. Via diagnostic connector OBD-II

    You will need a scanner that supports the protocol Nissan Consult (For example, Launch X431 Pro). Procedure:

    1. Подключите сканер к разъёму OBD-II.

    2. Выберите модель автомобиля и перейдите в меню Instrument Cluster.
    

    3. Найдите опцию Trip Meter Reset и подтвердите сброс.

    2. Through the on-board computer menu

    Relevant for models with a digital panel (Navara NP300, Ariya):

    1. Нажмите кнопку INFO на руле.

    2. Перейдите в Vehicle Settings → Meter → Trip Reset.
    

    3. Подтвердите действие кнопкой OK.

    3. Soft reset (for advanced users)

    On some models (for example, Nissan Leaf) you can reset the mileage through service menu:

    1. Выключите зажигание.

    2. Зажмите кнопку TRIP/RESET и включите зажигание (не запуская двигатель).
    

    3. Удерживайте кнопку 10 секунд, пока не появится сервисное меню.
    

    4. Выберите Trip Reset с помощью кнопки MODE.

    ⚠️ Attention: Incorrect actions in the service menu can lead to resetting all settings of the on-board computer, including data on fuel consumption and errors. Use this method only if you are confident in your actions.

    FAQ: Frequently asked questions about the Trip Reset button on Nissan

    Is it possible to reset the total mileage on a Nissan without consequences?

    No. Any interference with the odometer readings is recorded in the control units (BCM, ECM) and can be detected during diagnosis. In addition, this violates the law (in the Russian Federation - Article 159.1 of the Criminal Code). An exception is official recalibration after replacing the dashboard in a service center Nissan.

    Why does the mileage show the old values again after resetting Trip A?

    This indicates an odometer memory failure. Try:

    1. Disconnect the battery for 10–15 minutes.
    2. Check the instrument panel fuse (usually F10 or F20).
    3. Update firmware BCM through a diagnostic scanner.

    If the problem persists, contact service - the memory chip may need to be replaced.

    Where is the Trip Reset button on the Nissan Ariya?

    On Ariya There is no physical button. Reset is carried out via:

    1. Touch menu on the steering wheel (button INFO → Trip Meter).
    2. Voice command (if activated NissanConnect Services): say "Reset mileage».
    What should I do if the Trip readings are lost after replacing the battery?

    It is a normal phenomenon that when the power is turned off, temporary data (including Trip A/B) are reset to zero. The total mileage is stored in non-volatile memory. To avoid future data loss, before disconnecting the battery:

    • Record your current readings Trip A/B.
    • Use an external power source (eg starter charger).
    Is it possible to reassign another button to reset mileage?

    Technically yes, but this requires flashing the unit BCM and is not recommended without experience. On some models (for example, Nissan 370Z) enthusiasts reassign the mileage reset to the button CRUISE, but this may cause conflicts with other systems (for example, cruise control).