Removing the front bumper on a Nissan Almera G15: instructions with photos and nuances

Removing the front bumper Nissan Almera G15 - a task that owners face when repairing after an accident, replacing headlights, radiator grilles or installing additional equipment. Unlike European versions Nissan Almera N16 or Almera Classic, model G15 (produced from 2012 to 2019) has its own design features of the fasteners, which are important to consider so as not to break the plastic clips or damage the paintwork.

In this article you will find step-by-step instructions with photos, a list of necessary tools, as well as unique nuances of bumper mounting on Almera G15 with 1.5 and 1.6 liter engines (including versions with fog lights and parking sensors). We'll look at how to avoid common mistakes, such as forgotten screws at the bottom of the bumper or incorrectly removing clips near the wheel arches.

Preparing for dismantling: tools and safety precautions

Before you begin removing the bumper, make sure you have everything you need. The absence of even one tool can turn a simple procedure into agony. Here minimum setwhich will be required:

• 🔧 10 mm socket wrench (for bolts securing the bumper to the side members).
• 🔨 Screwdriver with Phillips bit (PH2) - for self-tapping screws in the lower part and under the wings.
• 🗝️ Plastic puller or flathead screwdriver (for careful removal of clips).
• 🔦 Flashlight or carrier — lighting of the engine compartment and the lower part of the bumper is mandatory!
• 🧤 Gloves - so as not to scratch your hands and leave fingerprints on the plastic.

Also prepare masking tape — you can use it to paste over the edges of the bumper and fenders to avoid scratches when removing. If on your Almera G15 installed fog lights or parking sensors, disconnect their connectors in advance to avoid damaging the wiring.

⚠️ Attention: Do not start work if the machine is on a slope or is not secured with the hand brake. Even slight movement of the car can lead to pinching of fingers between the bumper and the body.

If this is your first time removing the bumper, take a photo of the location of all the fasteners. before work starts. This will help avoid errors during reassembly. This is especially true for clips near the wheel arches - they can easily be confused with fender liner mounts.

Step-by-step instructions: removing the front bumper on Almera G15

The process of dismantling the bumper can be divided into: 4 stages: remove the clips under the hood, unscrew the bolts from below, disconnect the fasteners on the sides and final removal. Let's look at each step in detail.

Step 1: Open the hood and remove the upper fasteners

Start by opening the hood and locking it in the up position. At the top of the bumper you will see two plastic clips, which attach it to the radiator grille. Gently pry them up with a flathead screwdriver or plastic puller. Do not use excessive force - the clips are fragile!

Hidden under the clips two 10mm bolts — they need to be unscrewed with a socket wrench. If the bolts are stuck, use a penetrating lubricant (such as WD-40), but do not try to rip them off by force - this may damage the threads in the spar.

Step 2: Unscrew the bolts at the bottom of the bumper

Let's move on to the bottom of the car. Here Almera G15 has 4 screws (two on each side), which secure the bumper to the lower amplifier. They can be unscrewed with a Phillips screwdriver. If the car has a crankcase protection, it will have to be removed or bent.

Please note: on versions with fog lights Wires are laid under the bumper. They do not need to be disconnected at this stage - just carefully move them to the side.

Disconnect the negative terminal of the battery (if you plan to work with electricians)

Check for dirt or rust on the bolts - clean with a brush

Place cardboard or a rag under the bumper to avoid scratching the paintwork when removing

Make sure that all screws are unscrewed (lower mountings for headlights are often forgotten) -->

Step 3: Remove the side fastenings at the wheel arches

The most critical stage is disconnecting the bumper from the wheel arches. Here Almera G15 has each 3 clips on each side:

• One clip in the upper part of the arch (under the plastic fender liner).
• Two clips at the bottom (one closer to the bumper, the other to the threshold).

To get to them you will have to partially remove the fender liner (unscrew 2-3 screws and bend them). The clips are removed with a smooth upward movement. If the clip is broken, no big deal, it can be replaced with a new one (item number for Almera G15 — Nissan 77230-4M000).

⚠️ Attention: On vehicles with parking sensors The sensor wires are laid in the bumper. Do not pull the bumper sharply down - first disconnect the sensor connectors (they are located on the inside of the bumper and headlights).

Step 4: Final bumper removal

When all the fasteners are unscrewed, all that remains is to carefully pull the bumper off the latches. Start on one side, gradually releasing the clips all the way around. If the bumper is “bitten”, check to see if there are any unscrewed screws or undisconnected clips.

Place the removed bumper on a soft surface (for example, cardboard or a blanket) to avoid scratching it. If you plan to paint or repair it, cover all holes and connectors with masking tape.

Common mistakes and how to avoid them

Even experienced car owners sometimes make mistakes when removing the bumper. Here are the most common ones and how to prevent them:

Error	Consequences	How to avoid
Unscrewed screws at the bottom	Broken clips or cracks in the bumper	Check all fastenings according to scheme (see below)
Sharp jerking of the bumper down	Damage to parking sensors or PTF wiring	Disconnect connectors to full removal
Using metal tools to remove clips	Scratches on paintwork or broken latches	Use only plastic pullers
Unfixed hood	The hood hitting the bumper in a gust of wind	Secure the hood with a stop or ask an assistant to hold it

Another common problem is stuck bolts in the spars. If they do not give way, do not try to break them with a key. Better process WD-40 or Liquid Moly and wait 10-15 minutes. If the bolt still doesn't fit, try lightly tapping the key with a hammer (but not the bolt itself!).

What to do if the clip breaks?

If the clip breaks during removal, don't panic. It can be replaced with a new one (the cost of one clip is about 50-100 rubles). The main thing is not to lose the piece inside the arch, as it can rattle when moving. Plastic ties can be used for temporary fixation, but this is not a long-term solution.

Almera G15 front bumper mounting diagram

To ensure you don't miss a single fastener, use this diagram. It is relevant for all modifications Almera G15 (2012-2019), including restyled versions of 2016.

Upper part (under the hood):

• 2 plastic clips (attach the bumper to the radiator grille).
• 2 10 mm bolts (attach the bumper to the side members).

Bottom:

• 4 Phillips head screws (2 on each side).

Side parts (at wheel arches):

• 6 plastic clips (3 on each side).

Additionally (if any):

• 2 self-tapping screws for fastening fog lights (if installed).
• 4 clips for mounting parking sensors (on versions with parking systems).

On restyled Almera G15 (after 2016) additional may be present self-tapping screw in the central part of the bumper (under the license plate). It's easy to miss since it's hidden by a plastic plug.

Features of bumper removal on Almera G15 with different options

Nissan Almera G15 was produced in several trim levels, and this affects the process of removing the bumper. Let's look at the key differences:

Versions with fog lights (PTF)

If your car is equipped with PTF, before removing the bumper you must:

1. Disconnect the negative terminal of the battery.
2. Disconnect the headlight power connectors (they are located on the inside of the bumper).
3. Unscrew two additional screws securing the PTF to the bumper.

On some versions, the PTF wires go through a special harness, which is attached to the bumper with plastic ties. They need to be carefully cut and replaced with new ones during assembly.

Versions with parking sensors

Cars with parking sensors have additional 4 clips for fastening sensor wiring. They are located on the inside of the bumper, corresponding to each sensor. When removing the bumper, first disconnect the sensor connectors, and then carefully pull the wires out of the clips.

If the parking sensor is stuck to the bumper, do not try to tear it out. It is better to heat the mounting area with a hairdryer (temperature no higher than 60°C) to soften the sealant.

Versions with rear view camera (in the front bumper)

On some export versions Almera G15 rear view camera installed in the front bumper (for example, for all-round vision systems). In this case:

• Before removing the bumper, disconnect the camera connector.
• Remember the position of the camera relative to the body - if installed incorrectly, it will show a distorted image.
• Do not pull on the camera wires - they are fragile and may come off the board.

Bumper assembly: nuances and tips

Putting the bumper back often raises more questions than removing it. Here are the key points to help avoid problems:

1. Check all the clips - if they are broken, replace them with new ones. Reusing broken clips will cause the bumper to rattle on bumps.
2. Start with the side mounts — first snap the clips onto the wheel arches, then secure the upper and lower bolts.
3. Do not tighten the bolts immediately - first attach all the fasteners, then tighten them evenly so that the bumper stands straight.
4. Check clearances — there should be a uniform gap between the bumper and the fenders (2-3 mm). If one side is tighter, loosen the fasteners and adjust the position.

If after installation the bumper “walks” or rattles, the reasons may be the following:

• Loose bolts in side members.
• Broken or missing clips.
• Dirt gets between the bumper and the body (needs to be cleaned and reinstalled).

⚠️ Attention: On Almera G15 With automatic climate control, the outside air temperature sensor is often located behind the bumper shoe. When assembling, make sure that it is not pinched or covered by a bumper - otherwise the temperature readings will be incorrect.

FAQ: Frequently asked questions about removing the bumper on the Nissan Almera G15

Do I need to remove the wheels to remove the bumper?

No, it is not necessary to remove the wheels. It is enough to turn the steering wheel to its extreme position (to the left or to the right, depending on the side) and unscrew the self-tapping screws of the fender liner to gain access to the clips.

Can I remove the bumper alone or do I need an assistant?

Technically, you can remove the bumper alone, but this is inconvenient - it is bulky and can scratch the body. It is better to invite an assistant, especially if you are doing this for the first time.

What sealant should I use to seal the bumper after installation?

For Almera G15 Any silicone-based automotive sealant is suitable (for example, ABRO WS-904 or Permatex 81160). Apply a thin layer of it to the junctions of the bumper and the body, but do not overdo it - excess sealant may end up on the paintwork.

What should I do if the bumper does not fit snugly after installation?

The reasons may be different:

• Unevenly tightened bolts - loosen them and retighten them.
• Deformed clips - replace them.
• Dirt gets between the bumper and the body - clean the surfaces.
• Damaged fasteners on the bumper itself (for example, after an accident) - repair or replacement of the bumper may be required.

Where to buy clips and bolts for the Almera G15 bumper?

Original clips can be ordered by article number:

• Nissan 77230-4M000 — clip for attaching the bumper to the arch.
• Nissan 08915-40610 — bolt securing the bumper to the side member (M6x1.0).

Analogues (for example, from Febi or SWAG) are cheaper, but may differ in hardness. Buy from trusted stores such as Exist.ru or Autodoc.ru.