Removing the front bumper Nissan Almera G15 - a task that owners face when repairing after an accident, replacing headlights, radiator grilles or installing additional equipment. Despite its apparent simplicity, the process requires care: plastic clips are fragile, and improper dismantling can lead to damage to the body or the bumper itself. In this article we will analyze step by step instructions taking into account all the nuances of the model G15, including hidden fastenings and common mistakes.

Difference Almera G15 from previous generations - a modified design of the bumper mounts to the fender liners and front fenders. Used here as standard bolts 10 mm, and plastic caps, which easily break if handled carelessly. If you plan to remove the bumper for the first time, be patient and new clips (original article number - 08915-ZA00A for the front bumper).

Preparation for removal: tools and materials

Before starting work, make sure you have everything you need. The absence of even one tool can delay the process for hours. Basic set:

  • 🔧 A set of sockets and a ratchet wrench (the head must be on 10 mm And 12 mm).
  • 🔨 Plastic clip remover (or a flat screwdriver wrapped in electrical tape).
  • 🔩 Phillips screwdriver for fender liner screws.
  • 🧲 Magnet on the telescopic handle (so as not to lose the bolts in the engine compartment).
  • 🛠️ New plastic clips (at least 6 pieces) and rubber seals.

If the bumper is removed for painting or repair, prepare marker And tape - they will help mark the location of the clips during reassembly. Useful for garage work carrying case with LED lighting, since some mounts are located in poorly lit areas.

⚠️ Attention: Do not use metal tools to remove plastic clips! Even light pressure with a screwdriver can crack the fastener, and original spare parts for Almera G15 cost from 150 rubles per piece.
📊 Have you removed the bumper on a Nissan Almera before?
  • Yes, I did it myself
  • No, first time
  • Trusted the service
  • I don't know how it attaches

Step-by-step instructions: removing the front bumper

We start with dismantling wheel arch liners — they block access to the lower bumper mounts. To do this:

  1. Unscrew the screws around the perimeter of the fender liner (usually 4-5 pieces per side).
  2. Carefully bend the fender liner without tearing it off completely - it is attached to plastic pistons.
  3. Release the clips by pressing on the center and pulling up.

After removing the fender liners you will see three lower bumper bolts (one on each side and one in the center). They need to be unscrewed with a head 10 mm. Next we move on to the upper fastenings:

  • 🔹 Open the hood and unscrew the two bolts at the edges of the bumper (head 12 mm).
  • 🔹 Remove the radiator grille (it is attached with 4 clips).
  • 🔹 Disconnect the fog lamp connectors (if installed).

Now the bumper is only held side clips on the wings. To remove them, pull the bumper forward and down while pressing the clips with the puller. If the bumper does not budge, check that all the bolts are unscrewed - the central bolt under the license plate is often forgotten.

The fender liner bolts are unscrewed|The radiator grill is removed|PTF connectors are disconnected|The side clips are checked-->

Hidden fastenings and typical mistakes

The most common problem when removing a bumper on Almera G15 — unaccounted for clips under the headlights. They are not visible from the outside, but they hold the bumper at the top. To reach them:

  1. Remove the headlight (unscrew the 3 bolts at the back and disconnect the connector).
  2. Under the headlight you will find 1-2 plastic pistons - they need to be carefully removed with a puller.

Another common mistake is damage to latches on the bumper when trying to “rip” it from its place. Remember: the bumper must be removed smoothly, without jerking. If it doesn't work, it means you missed the fastener. Check:

Mounting location Fastener type Quantity
Wheel arch liners (lower) Bolt M6 3 pcs.
Wings (side) Plastic clip 4 pcs.
Radiator grille Latch 4 pcs.
Under the headlights Piston 2 pcs.
⚠️ Attention: On models Almera G15 with 360° camera (optional) a cable is laid in the bumper to the sensor at the bottom. Do not pull the bumper down without disconnecting the connector - you may break the wiring!
How to remove the bumper without removing the headlights?

This is possible, but requires skill. Need:

1. Bend the bumper forward as far as possible.

2. Find the clip through the gap between the headlight and the bumper and press it with a puller.

3. Repeat for the second side.

The risk of damage to the headlight is higher, so the method is not recommended for beginners.

Removing the bumper with parking sensors

If your Almera G15 equipped parking sensors, before removing the bumper, you must disconnect the sensors. They are attached to the bumper with latches and connected to wires going into the cabin. Procedure:

  1. Disconnect the negative terminal of the battery (required!).
  2. Remove the plastic trim under the bumper (held on by 4 screws).
  3. Carefully remove the sensors from their sockets by pressing the latch on the back.
  4. Disconnect the connectors and label them (the sensors should return to their places!).

When reassembling check the tightness of the seals sensors - if they are damaged, moisture will get into the connectors, which will lead to false alarms of the parking sensors. Original seals for Almera G15 have an article number 28511-JK00A.

💡

Before removing the sensors, take a photo of their location with your phone. Even if you are sure that you will remember the order, a photo will help avoid confusion during assembly.

How to remove a bumper without damage: tips from the experts

Experienced car mechanics share several tricks that will help preserve the bumper and body Nissan Almera G15 intact:

  • 🔥 Heating the clips. In cold weather, plastic becomes brittle. Before removing, warm up the clips with a hairdryer (temperature no higher than 60°C).
  • 🧲 Magnet for bolts. Glue a small magnet to the key - this will prevent the bolts from falling into the engine compartment.
  • 📏 Marking. Apply marks with a marker to the bumper and body so that they can be aligned without distortion during assembly.

If the bumper is removed for painting, do not clean it of old sealant with metal brushes - they scratch the plastic. Use plastic spatula and special washes (for example, Body 700).

When installing a new bumper, check gaps between him and the wings. They should be the same on both sides (optimally 3–5 mm). If the gaps are different, the problem may be deformed body mounts.

💡

Key Point: Never pull on the corners of the bumper! The load must be distributed evenly across the entire width, otherwise the plastic will crack at the attachment points to the wings.

Reassembly: how to avoid squeaks and distortions

Installing the bumper on Almera G15 often accompanied creaks And loose fit. To avoid this:

  1. Clean all contact surfaces of the bumper and body from dirt and old sealant.
  2. Apply silicone grease on the rubber seals of the clips.
  3. Tighten the bolts criss-crossto avoid skew (first the lower ones, then the upper ones).
  4. After assembly, check the bumper for play by shaking it with your hands.

If after installation the bumper sags in the center, the problem may be in loose fastenings of the radiator grille. Tighten the grille bolts and check the integrity of the plastic latches on the bumper.

For additional fixation, some masters use 3M double sided tape where the bumper meets the fenders. However, this is a temporary solution - the next time you remove the tape, you will have to clean it, which can damage the paintwork.

Frequently asked questions about removing the bumper on a Nissan Almera G15

Do I need to remove the headlight to remove the bumper?

Not necessary, but without this it will be difficult to get to the hidden clips under the headlight. If the bumper is removed to replace lamps or repair a headlight, it is logical to remove it in advance.

How many clips break on average the first time you remove them?

If you work carefully - 1-2 pieces. Most often, the side clips on the wings break. Always have spares (item no. 08915-ZA00A).

Is it possible to remove the bumper without a pit or lift?

Yes, but it's less convenient. You will have to lie under the car to get to the bottom bolts. Use rolling jack with safety stop.

What sealant should I use to seal the bumper?

For Almera G15 will do sealant spray for plastic (For example, Liqui Moly Kunststoff-Pflege). Do not use silicone sealants - they will flake off over time.

What should I do if after assembly the bumper does not match the fenders?

Check:

  • Are all the clips in place?
  • Are the fastenings on the body deformed?
  • Are the bolts tightened evenly (misalignment even by 1 mm is visually noticeable).

If the problem persists, the bumper may be deformed and will require adjustment or replacement.