Removing the rear seat on a Nissan Qashqai J10: instructions with photos and tips

Rear seat in Nissan Qashqai J10 (2007–2013) requires dismantling not only when replacing upholstery or repairing mechanisms, but also to access hidden elements: the fuel pump, electrical wiring or heating system. Unlike newer models, J10 has a unique mounting design, where plastic latches and metal bolts are combined. Improper dismantling can lead to breakage of the fasteners or damage to the casing - so it is important to know all the nuances.

In this article you will find step-by-step instructions with photos, a list of necessary tools, as well as unique tips for working with seat cushion and backrest fastenings, which are not in standard manuals. We will also look at common mistakes and ways to avoid them, so that the process takes no more than 30 minutes.

Preparation: Tools and Safety Precautions

Before starting work, make sure you have everything you need. To remove the rear seat Qashqai J10 No specialized tools are required, but some accessories will greatly simplify the process:

• 🔧 12 mm socket wrench (or a head with a ratchet) - for unscrewing the backrest mounting bolts.
• 🔨 Flat head screwdriver (medium size) - for prying up the plastic latches of the pillow.
• 🧲 Magnetic holder — so as not to lose bolts and nuts in the cabin.
• 🧴 Silicone grease (WD-40) - if the fasteners are rusty or stuck.
• 📸 Smartphone — for photographing the location of the wires (if there are heated seats).

Pay special attention security:

• ⚡ Disconnect the negative terminal of the battery if you plan to work with electrical wiring (for example, when disconnecting heating connectors).
• 👶 Make sure there are no children or animals in the cabin - a sudden fall of the seat back can injure them.
• 🧤 Wear gloves to avoid cuts from the sharp edges of the metal frame.

⚠️ Attention: If your Qashqai J10 equipped with side airbags in the rear seats, do not disconnect the power connectors without first removing the SRS fuse (number F30 in the fuse box under the steering wheel). Otherwise, a security error may occur.

Removing the rear seat cushion

The seat cushion (lower part) is attached to the body using two plastic latches on the front And two metal hooks at the back. To remove it:

1. Fold the seat back forward (if possible) or recline it as far as possible to access the front latches.

2. Insert a flathead screwdriver between the cushion and the plastic floor sill at the front edge of the seat. Gently push up to release the first latch. Repeat for the second latch.

3. Lift the pillow up and pull it towards you - the back hooks should come out of the grooves. If the seat is stuck, check to see if it is catching on the seat belts.

On some versions Qashqai J10 under the pillow there may be additional fastenings for ISOFIX - they need to be unscrewed with a socket wrench 10 mm. Also, debris and small items often accumulate under the seat, so prepare a vacuum cleaner.

⚠️ Attention: If the seat cushion is equipped heated, do not pull it sharply - first disconnect the power connector (usually it is located under the central part of the seat and is covered with a black cover).

Removing the rear seat back

The backrest is attached to the body four bolts (two on each side) and is fixed in the upper part due to plastic clips. To remove it:

1. Remove the plastic plugs in the lower corners of the back (they are attached with latches - pry them off with a screwdriver).

2. Unscrew the bolts with a socket wrench on 12 mm. If the bolts are stuck, treat them with WD-40 10-15 minutes before unscrewing.

3. Gently pull the back up to release the top clips. If necessary, help with a screwdriver, but do not use excessive force - the clips are fragile.

On models with split backrest (60/40) Each part is removed separately. At the same time left side (40%) may have an additional bolt securing it to the central pillar - it is easy to miss.

Seat element	Number of fasteners	Mounting type	Tool
Seat cushion	4	2 plastic latches + 2 metal hooks	Flat head screwdriver
Back (solid)	4	M8 bolts + 2 clips	Socket wrench 12 mm
Back (split 60/40)	6	M8 bolts + clips + extra bolt	Socket wrench 12 mm, WD-40
Heated seat	1	Power connector	Screwdriver for removing the cover

Nuances for different trim levels of Qashqai J10

The design of the rear seat may vary depending on the configuration and year of manufacture. Here are the key features:

• 🚗 Basic equipment (2007–2010): the back is solid, secured with 4 bolts, no heating.
• 🚗 Tekna/LE trim levels (2010–2013): split backrest 60/40, additional fastening bolt, heating possible.
• 🚗 Models with ISOFIX: There are metal brackets under the seat cushion that may interfere with removal.
• 🚗 Restyled versions (after 2010): Plastic back clips are more fragile and require caution.

On vehicles with panoramic roof The upper back clips may be hidden by the trim - you need to look for them by touch. If you remove the seat for installation subwoofer or battery, keep in mind that in Qashqai J10 Underfloor space is limited due to the location of the fuel tank.

How to check if the seat is heated?

Heating is available if there is a button with a seat icon and wavy lines on the center console (next to the gearshift lever). You can also look under the pillow - there will be a wiring harness with a connector.

Common mistakes and how to avoid them

Even experienced car owners make mistakes when removing the rear seat. Here are the most common:

1. The plastic latches of the pillow are broken. The reason is an attempt to raise the seat without first releasing the front latches. Solution: Always start from the front edge, using the screwdriver as leverage.

2. Lost backrest bolts. The bolts are small and easily fall under the skin. Solution: Use a magnetic holder or place a cloth.

3. Damage to heating wiring. A sharp tug on the connector can break the contacts. Solution: First take a photo of the location of the wires, then carefully disconnect the connector by pressing the latch.

4. Backrest jamming during installation. If the clips do not fit into the grooves, the back will dangle. Solution: When installing, press down on the top edge of the backrest until it clicks.

Another common problem is creaking after installation. It occurs if the seat cushion is not tightly seated on the hooks or the backrest bolts are not fully tightened. To eliminate the squeak, check:

• Are all bolts tightened (torque - 20 Nm).
• Is there any debris between the cushion and the floor?
• The integrity of the rubber gaskets under the bolts (if worn, they must be replaced).

Cleaning and maintenance after dismantling

A removed seat is a great excuse to spend deep cleaning and service. Here's what to do:

• 🧹 Use a vacuum cleaner to remove debris from under the pillow (sand, crumbs and even coins often accumulate there).
• 🧼 Clean the trim a special product for fabric or leather (depending on the material). For Qashqai J10 suitable with fabric upholstery Autoglym Interior Shampoo.
• 🔧 Check adjustment mechanisms backrests - if necessary, lubricate them with silicone grease.
• 🔋 Inspect the heating wiring for damage or oxidation of contacts.

If you removed the seat to access fuel pump, pay attention to the condition sealing rubber around the hatch. Over time, it tans and lets gasoline vapors into the cabin. Replace it at the first sign of wear (part number - 17352-JM00A).

For owners who are planning install a subwoofer or extra battery, it is important to consider the load on the floor. B Qashqai J10 maximum permissible load on the rear part of the body - 200 kg. Exceeding may result in floor deformation.

Installing the seat back: step-by-step algorithm

Reassembling the rear seat is done in reverse order, but there are a few key pointsthat are often missed:

1. Make sure everything plastic clips the backs are intact and in their places. If they are broken, replace them (they are inexpensive, but without them the back will wobble).

2. When installing the cushion, first hook back hooks the grooves in the floor, then press the front edge until the latches click into place.

3. Tighten the back bolts criss-crossto avoid skew. Tightening torque - 20 Nm (do not overtighten!).

4. If you removed the heating connector, check it polarization (polarity) before connecting. Incorrect connection may damage the system.

After installation, check:

• Fixation of the backrest in vertical and reclined positions.
• The operation of seat belts (they should not cling to the seat).
• No squeaks when driving over uneven surfaces.

⚠️ Attention: If the light comes on after installation Airbag on the dashboard, it means you forgot to turn off the fuse SRS or the airbag connector is damaged. In this case, the error must be reset via a diagnostic scanner (for example, Launch X431).

FAQ: Frequently asked questions about removing the rear seat on the Qashqai J10

Is it possible to remove the seat back without unscrewing the bolts?

No, the backrest is secured with bolts, and they must be unscrewed. However, if you only need access to the trunk (for example, to transport long cargo), you can fold the backrest forward without removing it completely. To do this, pull the lever under the seat cushion (on the right or left, depending on the side).

How to remove the seat cushion if the latches are broken?

If the plastic latches are broken, they can be temporarily replaced with metal staples or self-tapping screws with press washer (diameter 4–5 mm). However, it is better to buy original latches (article - 80310-4M000 for Qashqai J10). They are inexpensive, but provide reliable fixation.

What to do if the backrest bolts are rusty and cannot be unscrewed?

Treat the bolts first penetrating lubricant (For example, WD-40 Specialist or Liqui Moly MoS2) and let it soak in for 15–20 minutes. If this doesn't help, try:

• Use impact wrench (but do not overdo it so as not to strip the thread).
• Place the bolt in the center and drill it out with a drill 5 mm, then unscrew with an extractor.
• Heat the bolt construction hairdryer (up to 200°C) - this will help break down the rust.

After dismantling, replace the rusty bolts with new ones (original 08915-40610).

Where is the SRS fuse for disabling the airbags in the Qashqai J10?

fuse SRS (number F30, 10A) is in fuse box under the steering wheel. To get to it:

1. Open the block cover (it is located to the left of the steering column).
2. Find the fuse labeled SRS AIRBAG or F30.
3. Remove it with pliers or special tweezers (usually included with the machine).

After work, do not forget to install the fuse back!

Can the removed seat trim be washed in the washing machine?

No, the washing machine can damage foam base and sheathing seams. For cleaning:

• Use interior cleaning foam (For example, Karcher RM 519).
• Apply the product soft brush, do not rub too hard to avoid damaging the fabric.
• To remove stains, use steam generator (temperature no higher 100°C).
• Dry the sheathing in the shade, avoiding direct sunlight (they can cause shrinkage of the material).