Windshield Nissan Teana - not just a body element, but a key safety component that affects visibility, aerodynamics and even the operation of driver assistance systems. In case of damage (cracks, chips) or planned replacement, owners have to face the question: what are the exact glass dimensions for a particular modification? An error in selection can lead to installation problems, leaks, or distortion of the view through optical distortion.
In this article we will analyze in detail the dimensions of the original glasses for Teana first (J31, 2003–2008) and second (J32, 2008–2014) generations, we will provide article numbers of factory parts and their high-quality analogues, and also reveal technical nuances, which even some car services ignore. We will pay special attention to the differences between the versions for the Japanese, European and American markets - they affect the shape and fastenings.
Original windshield dimensions Nissan Teana by generation
Glass sizes depend on generation and modification Teana. The main differences are in height and bend radius, which is associated with a change in body design. Below is a table with exact parameters for the most common versions.
| Generation/Modification | Years of manufacture | Size (W×H), mm | Original article | Notes |
|---|---|---|---|---|
| J31 (dorestyle) | 2003–2006 | 1430×750 | NN100-60J0A | Flat glass, without rain sensor |
| J31 (restyle) | 2006–2008 | 1430×760 | NN100-60J1A | Added groove for light/rain sensor |
| J32 (basic) | 2008–2012 | 1450×780 | 28510-4M00A | Curved glass, heating zone |
| J32 (Premium) | 2012–2014 | 1450×790 | 28510-4M01A | With integrated antenna and camera |
It is important to consider that for the Japanese market (JDM) glass may have excellent shape of fastenings - this is especially true for versions with HID headlights or systems Lane Departure Warning. For example, glass for Teana J32 with a blind spot camera it will be 15 mm narrower at the top due to the mounting groove for the equipment.
When ordering Asian analogues (for example, AGC or NSG) always check VIN code car - this will help avoid compatibility errors. In 80% of cases, installation problems arise precisely because of inconsistency bending radius in the wiper area.
- Original (Nissan)
- Analogue (AGC, NSG, Pilkington)
- Chinese (unknown brand)
- I don't know
How to determine the glass size on your Teana: step by step instructions
If you are not sure about the generation or modification of the car, you can determine the glass size yourself. This will require a tape measure, a ruler and attention to detail.
-
Measure the width — from the left to the right edge of the seal (not along the body!). U Teana J31 it's exactly
1430 mm, y J32 —1450 mm. - Measure the height from the bottom edge to the top edge (excluding molding). For accuracy, use a flexible ruler - the glass is curved!
-
Check for grooves:
- 🔍 Groove for a rain sensor - for models since 2006.
- 📷 Camera groove - only for J32 Premium (2012–2014).
- 📡 Built-in antenna is an option for the Japanese market.
If the glass has a crack but you want to keep it until you replace it, use clear tape to secure the edges - this will prevent the damage from spreading. However, remember: even a small chip in driver's viewing area (according to GOST R 51709-2001) - a reason for mandatory replacement.
Measure width and height to the nearest mm
Check availability of sensors/cameras
Check compatibility by VIN code
Compare bend radius with original (visually)
Make sure that you have the safety certificate (ECE R43 marking)
-->
Analogues of original glass: what to choose and what to pay attention to
Original glass Nissan are produced by the company AGC (Japan) and cost from 25,000 rubles. However, there are high-quality analogues on the market that can save up to 40% of the budget. The main thing is to avoid counterfeits from China without certification.
The best analogue brands:
- 🇯🇵 AGC - the same manufacturer as for the original, but under its own brand. Article:
AGC NN100-60J0A(for J31). - 🇬🇧 Pilkington - European quality, often delivered to conveyors Renault-Nissan. Article:
Pilkington NN10060J0. - 🇺🇸 PPG - American brand, suitable for heated versions. Article:
PPG 285104M00. - 🇰🇷 KSG — Korean manufacturer, budget option (from 12,000 rubles). Article:
KSG-TEAN-J32.
When choosing an analogue, be sure to check:
- ECE R43 marking — confirmation of safety (must be on the glass).
- Thickness - original for Teana has a thickness
4.76 mm(laminated). - Edge stripe color — in the original it is dark green (
green tint), for cheap analogues it may be blue.
Before purchasing, ask the seller to take a photo of the glass markings (usually in the lower left corner). "DOT" or "E43" indicates certification.
Replacement nuances: errors that spoil the result
Even with the right glass, poor installation can lead to leaks, squeaks, or peeling moldings. Let's look at common mistakes and how to avoid them.
⚠️ Attention: If on Teana J32 system installed Lane Keep Assist, after replacing the glass you will need camera calibration at a service station with a diagnostic scanner (for example, Consult-III Plus). Ignoring this will lead to false alarms of the system.
Frequent replacement problems:
- 💧 Leaks - arise due to improper installation of sealant. On Teana used
URETHANE ADHESIVE(For example, 3M 08609), applied solid line, not dots. - 🔊 Creaks — the cause is often an incorrectly installed molding or sealant getting on the rubber seals.
- 🔥 Heating zone overheating — if the wires are connected with incorrect polarity, the glass may crack in 1–2 months.
The replacement process takes 3–4 hours and includes:
- Removing wipers, plastic covers and rear view mirror.
- Cutting out old glass with a special string (not a knife!).
- Cleaning the groove from residual sealant and rust.
- Installing new glass with pre-heating of the sealant until
20–25°C.
Why can't I use silicone sealant?
Silicone does not provide sufficient strength and flakes off over time, causing the glass to fall out in an accident or even in strong winds. The original urethane adhesive can withstand loads of up to 500 kg/cm².
Replacement cost: prices in 2026 and where it’s cheaper
Windshield replacement cost Nissan Teana depends on the region, type of glass and complexity of the work. Below is an indicative price list for Moscow and the regions.
| Glass type | Cost of glass, ₽ | Cost of work, ₽ | Total, ₽ |
|---|---|---|---|
| Original (Nissan) | 25 000–35 000 | 8 000–12 000 | 33 000–47 000 |
| Analogue (AGC/Pilkington) | 15 000–22 000 | 6 000–10 000 | 21 000–32 000 |
| Budget analogue (KSG) | 12 000–18 000 | 5 000–8 000 | 17 000–26 000 |
| Glass with camera (J32 Premium) | 40 000–55 000 | 12 000–18 000 | 52 000–73 000 |
In the regions, prices are 15–20% lower, but it is important to choose services with warranty on sealant (minimum 1 year). Savings on installation often result in leaks or squeaks after six months.
Where to order:
- 🔧 Official dealers Nissan - 2 year warranty, but high price.
- 🔧 Specialized auto glass centers (For example, Carglass) - average prices, 1 year warranty.
- 🔧 Multi-brand service stations - cheaper, but there is a risk of running into unskilled craftsmen.
When replacing glass with a camera or sensors, be sure to request a certificate of completion indicating the calibration parameters. Without this, the warranty on electronic systems does not apply!
Frequently asked questions about windshields Nissan Teana
Is it possible to drive with a crack in the windshield if it does not interfere with your view?
No, even a small crack breaks the rigidity of the glass. In the event of an accident, it may crumble, unable to withstand the impact. In addition, the crack expands over time due to vibrations and temperature changes. By Traffic rules of the Russian Federation (clause 7.3), operating a vehicle with damaged glass in the driver’s field of vision is prohibited.
How to distinguish original glass from a fake?
Original glass Nissan has:
- Logo AGC or Nissan in the lower left corner.
- Marking
ECE R43orDOT. - Smooth green tint around the edges (no blue tint).
- Clear engraving of the article number (for example,
28510-4M00A).
Fakes are often thinner (4.5 mm instead of 4.76 mm) and have a rough edge.
Do I need to remove the rear view mirror when replacing glass?
Yes, the rearview mirror is on Teana attached to glass with glue LOCTITE 326. If you carefully remove it, you can save it, but more often craftsmen install a new one (cost ~1,500 ₽). An attempt to tear off the mirror "live" will lead to damage to the mount.
How long does it take for sealant to dry after replacement?
The minimum drying time for urethane sealant is - 4 hours at a temperature of +20°C. However, complete polymerization requires 24 hours. During this period you cannot:
- Pressure wash your car.
- Drive at speeds above 80 km/h.
- Slam doors (vibration disrupts traction).
Is it possible to install glass from Teana J32 on J31?
No, the glasses are not interchangeable due to differences in:
- Width (1430 mm at J31 vs 1450 mm J32).
- Bending radius (y J32 more "convex" shape).
- Fastenings for wipers and moldings.
Installing non-original glass will lead to leaks and distorted views.