Nissan Terrano is a popular crossover that has won the trust of car owners due to its reliability and cross-country ability. However, when choosing new wheels or tires, many are faced with the question: What is the bolt pattern on the Nissan Terrano?? Not only the appearance of the car, but also safety on the road depends on the correct selection of parameters.

In this article we will look at all the key parameters: PCD (bolt pattern), disc offset (ET), central hole diameter (DIA), as well as compatibility with other models Nissan And Renault. You will learn how to measure the bolt pattern yourself, which wheels will fit without modifications, and what to look for when purchasing.

We will pay special attention to differences between generations Terrano (including restyled versions) and the nuances of tire selection - from standard sizes to possible upgrades. If you're considering installing aftermarket wheels or tires, you'll find trusted data and expert advice here.

What is a bolt pattern and why is it important for Nissan Terrano

Bolt Pattern (PCD) - this is a parameter that determines the number of bolt holes on the wheel rim and the diameter of the circle on which they are located. For Nissan Terrano this indicator is critical: incorrect selection will lead to the fact that the disk will not sit on the hub or will be unevenly fixed, which can lead to vibrations at high speeds and even wheel separation.

For example, if on your Terrano bolt pattern 5×114.3, and you install the disk with 5×112, the bolts will not align with the holes, or the disk will be fixed skewed. Consequences: steering wheel beating, accelerated wear of bearings and balls, and in the worst case, an accident.

  • 🔧 PCD - number of holes × circle diameter (for example, 5×114.3).
  • 📏 ET (departure) — the distance from the mating plane of the disk to its center. Affects the width of the wheelbase.
  • ⭕ DIA — diameter of the central hole of the disk. Must match the hub diameter.
  • 🔩 Fastener type - for Terrano bolts are usually used M12×1.25.
⚠️ Attention: Some sellers position discs as “universal” for several models, but in reality their PCD may differ slightly. For example, 5×114.3 And 5×115 visually similar, but not interchangeable!

Nissan Terrano bolt pattern table by generation

Bolt pattern parameters depend on the year of manufacture and modification Terrano. Below is the current table for all generations, including restyled versions. The data is confirmed by the manufacturer and tested in practice by the owners.

Generation/Modification Years of manufacture PCD (bolt pattern) ET (reach), mm DIA (hole diameter), mm Fastener thread
Nissan Terrano I (R20) 1986–2005 6×139.7 0…+15 106.1 M12×1.25
Nissan Terrano II (R50, restyling) 2013–2020 5×114.3 35…45 66.1 M12×1.5
Renault Duster (similar to Terrano II) 2015–present 5×114.3 38…50 66.1 M12×1.5
Nissan Terrano (India, Latin American market) 2014–present 5×114.3 35…40 66.1 M12×1.5

Please note: Terrano II (2013–2020) built on the platform Renault Duster, therefore their bolt pattern parameters are identical. This means that the drives are from Duster, Nissan Almera G15 or Renault Kaptur suitable for Terrano without modifications.

📊 What Nissan Terrano do you have?
  • First generation (R20)
  • Second generation (R50)
  • Indian/Latin American version
  • I don't know

How to measure the bolt pattern on a Nissan Terrano yourself

If you are not sure about the parameters of your car or are buying used wheels, it is better to double-check the bolt pattern yourself. To do this you will need a caliper and a ruler. Let's consider two methods: for an even and odd number of holes.

Method 1: Even number of holes (eg 5×114.3)

  1. Measure the distance between the centers of two adjacent holes (for example, A = 72 mm).
  2. Multiply the result by the coefficient:
    • For 4 holes: A × 1.414.
    • For 5 holes: A × 1.701.
  • For Terrano II with 5×114.3 the distance between adjacent holes should be ~67.1 mm (67.1 × 1.701 ≈ 114.3).

    • Method 2: Odd number of holes (eg 6x139.7 on Terrano I)

    Measure the distance between the centers of the two furthest holes (for example, B = 139.7 mm). For 6 holes this will be the diameter of the circle (PCD = B).

    ☑️ Tools for measuring bolt pattern

    Done: 0 / 4
    ⚠️ Attention: When measuring, keep in mind that paint or dirt on the hub may distort the results. Clean the surface before measuring! Also don't be confused PCD with the diameter of the central hole (DIA) are different parameters.

    Wheel compatibility: which models are suitable for Nissan Terrano

    Thanks to the unification of the platform Nissan-Renault, for Terrano II Wheels from several models are suitable. However, it is important to consider not only the bolt pattern, but also departure (ET), rim width And diameter.

    • 🔄 Full compatibility: drives from Renault Duster, Nissan Almera G15, Renault Kaptur (if it matches ET).
    • ⚠️ Partial compatibility: drives from Mitsubishi ASX or Suzuki SX4 - verification required DIA And ET.
    • ❌ Incompatible: drives from Nissan Qashqai (5×114.3, but different DIA = 66.1 vs 67.1).

    Example: if on your Terrano II the wheels cost 6.5J×16 ET40, you can install disks from Duster with parameters 6.5J×16 ET38 — difference in departure (ET) 2 mm is acceptable and will not affect handling.

    💡

    When buying used wheels, check them for runout! Place the disk on a flat surface and spin it - if there is play or vibration, such a disk should not be taken.

    Tire selection for Nissan Terrano: standard and alternative sizes

    Tire size for Terrano depends on the generation and modification. The manufacturer recommends the following parameters:

    Generation Standard tire size Valid Alternatives Disc diameter, inches
    Terrano I (R20) 215/80 R15 235/75 R15, 205/80 R16 15–16
    Terrano II (R50) 215/65 R16 215/60 R17, 225/60 R16 16–17
    Terrano (India) 215/65 R16 215/60 R17 16–17

    When choosing alternative sizes, consider:

    • 📏 Tire outer diameter should not differ from the standard by more than 3%. For example, for 215/65 R16 (diameter 685 mm) acceptable size 215/60 R17 (diameter 684 mm).
    • ⚖️ Load Index must be no lower than standard (for example, 98T for Terrano II).
    • ❄️ Seasonality: for winter, choose tires with markings M+S or 3PMSF.
    What happens if you install tires of a non-standard size?

    An increase in diameter by more than 3% will lead to incorrect operation of the speedometer (readings will be underestimated) and increased load on the transmission. Tires that are too wide can rub against the fender liners when turning.

    Common mistakes when choosing wheels and tires for Terrano

    Even experienced car owners sometimes make mistakes that lead to drivability or safety problems. Here are the most common:

    1. Ignoring crash (ET). Installing discs with offset ET20 instead of ET40 will move the wheel outward, which will increase the load on the wheel bearings and worsen directional stability.
    2. Mismatch DIA. If the diameter of the center hole of the disc is larger than that of the hub, use centering rings. Without them, the disc will not be attached evenly.
    3. Saving on bolts. Bolts from Nissan Almera (M12×1.5) are not suitable for Terrano I (M12×1.25) — the thread is different!
    4. Incorrect tightening torque. For Terrano II the tightening torque of the bolts should be 90–110 Nm. Over-tightening deforms the disc, under-tightening leads to loosening of the bolts.
    💡

    Always check discs for runout before installation! Even a new disc may have a manufacturing defect, which will only appear at speeds above 100 km/h.

    Modifications and tuning: what can be changed without risk

    Many owners Terrano want to improve appearance or cross-country ability through non-standard wheels and tires. However, not all changes are safe. Let's consider the valid options:

    • 🔼 Increasing disc diameter: with R16 to R17 (for Terrano II) is possible provided that the tire profile is reduced (for example, 215/65 R16 → 215/60 R17).
    • 🔽 Disc widening: maximum width for Terrano II — 7.5J (standard - 6.5J). Wider rims will require rolling out the arches.
    • 🏔️ Mud tires: Off-road tires can be installed 215/75 R15 (for Terrano I), but this will increase fuel consumption and worsen handling on asphalt.

    When tuning, be sure to consider:

    • 📉 Clearance: Increasing the wheel diameter reduces ground clearance.
    • ⚖️ Suspension load: Heavy discs (for example, cast instead of stamped) accelerate wear on the shock absorbers.
    • 🚦 Legal rules: in Russia it is prohibited to exceed the body dimensions by more than 40 mm (according to GOST R 52390-2005).

    FAQ: Answers to popular questions about the Nissan Terrano bolt pattern

    Is it possible to install Nissan Qashqai wheels on Terrano II?

    No, despite the same bolt pattern 5×114.3, y Qashqai diameter of the central hole (DIA) is equal 67.1 mm, and Terrano II — 66.1 mm. Without centering rings, the disc will not seat correctly.

    What bolts are needed for Terrano I (R20)?

    For Terrano I threaded bolts are used M12×1.25 and a length of at least 25 mm. Tightening torque - 80–90 Nm.

    What happens if you install wheels with an offset of ET30 instead of ET40?

    Reducing the offset by 10mm will move the wheel outward by 10mm on each side. This will increase the load on the wheel bearings and may cause the tire to rub against the wheel arch liner when the vehicle is fully loaded.

    Will 225/60 R16 tires fit the Terrano II?

    Yes, but with reservations: the outer diameter of such a tire is 1.5% larger than the standard one (215/65 R16), which is not critical. However, the width 225 mm may require rolling out the arches at maximum rotation angles.

    How often should the bolt pattern be checked during operation?

    There is no need to check the bolt pattern regularly - this is a static parameter. However, it is recommended to inspect the rim mounts every 10–15 thousand km (or when changing tires seasonally) for corrosion of the bolts or deformation of the holes.