Nissan Teana J31 bolt pattern: how to choose the right wheels and tires

Nissan Teana J31 is a business sedan that has gained popularity due to its reliability, comfort and balanced driving performance. However, when replacing wheels, many owners are faced with the question: what is the bolt pattern of this model? An error in choosing parameters can lead to vibrations, accelerated wear of the suspension, or even an emergency. In this material we will analyze all the nuances: from standard values PCD, ET And DIA up to compatibility with rims from other cars Nissan.

Feature Teana J31 (2003–2008) is that its wheel parameters depend on the configuration and sales market. For example, Japanese versions may differ from European or American versions. We have collected current data for all modifications, including rare variants with factory wheels 17".

What is a bolt pattern and why is it important for Nissan Teana J31

Bolt pattern (or PCD - Pitch Circle Diameter) is the diameter of the circle on which the holes for attaching the disc to the hub are located. For Teana J31 this parameter is critical: incorrect selection will lead to the disc not fitting tightly and the bolts being tightened skewed. Consequences:

• 🔧 Steering wheel vibration at speeds over 80 km/h due to imbalance.
• 🚗 Accelerated wear wheel bearings and ball joints.
• 💥 Risk of wheel separation during emergency braking (in critical cases).

Except PCD, other parameters are also important:

• 📏 ET (Departure) — the distance from the mating plane of the disk to its center. A deviation of more than ±5 mm is fraught with friction against the arch or suspension.
• ⭕ DIA (Diameter of Center Hole) - must match the diameter of the hub or be larger (using adapter rings).
• 🔩 Type of mounting bolts - for Teana J31 bolts are used M12×1.25 with conical fit.

Standard bolt pattern parameters for Nissan Teana J31

Basic values for most versions Teana J31 (2003–2008):

Parameter	Meaning	Note
PCD (Bolt Pattern)	5×114.3	Typical standard for most models Nissan And Infiniti.
ET (Departure)	+35…+45 mm	Depends on the width of the disk. For 16" usually +40 mm, for 17" — +35 mm.
DIA (Central Hole)	66.1 mm	Matches the diameter of the hub. Discs with larger DIA are allowed when using rings.
Bolt thread	M12×1.25	Cone fit (cone angle 60°).

Important: On some versions for the Japanese market (for example, Teana 250XS) could be installed PCD 5×100 - this is rare, but before purchasing wheels, check this point using the VIN code or measuring the existing wheels.

How to measure PCD on your own:

1. Remove one wheel and clean the hub of any dirt.
2. Measure the distance between the centers of two adjacent holes (for example, 70 mm).
3. Multiply by factor 1.05 for 5 holes: 70 × 1.05 ≈ 73.5 mm is the radius of the circle. Double it to get PCD (147 mm in the example).

Recommended wheel and tire sizes for Teana J31

Factory wheel sizes depend on the configuration. Below is the data for the most common options:

Equipment	Disk size	Tire size	ET (Departure)
Basic (2.0/2.3)	6.5J×16	215/60 R16	+40 mm
Luxury (2.5/3.5)	7J×17	225/55 R17	+35 mm
Sports (3.5 V6)	7.5J×18	235/50 R18	+35 mm

Permissible deviations:

• 🔄 Disc width: ±0.5 inches from factory size (for example, instead of 7J you can put 6.5J–7.5J).
• 📉 Departure (ET): ±5 mm. Reducing overhang (e.g. ET30 instead of ET35) will widen the track, but will increase the load on the wheel bearings.
• 🎯 Diameter: Can be increased by 1-2 inches (e.g. with 16" on 17"), but the tire must be selected with a smaller profile to maintain the outer diameter of the wheel.

⚠️ Attention: Installing disks 18" on version with engine QR20DE (2.0 L) may cause the tire to touch the arch when the vehicle is fully loaded. Check the clearances on the lift!

Compatible with other Nissan and Infiniti models

Thanks to standard bolt pattern 5×114.3 drives from Teana J31 fits many models Nissan And Infiniti. However, one must take into account ET And DIA:

• 🚗 Nissan Maxima A33/A34 - full software compatibility PCD And DIA, but the offset may vary (ET35–45).
• 🚙 Nissan Altima L31/L32 - rims fit 16–17", but check the clearance for 18".
• 🏎️ Infiniti G35 (V35) - matches PCD, but the central hole is larger (73.1 mm), you will need rings.
• 🚐 Nissan Murano Z50 - the discs are interchangeable, but Teana Discs with ET < 30 mm.

Example of a successful replacement: disks from Infiniti FX35 (size 18×8J ET35) fit on Teana J31 3.5 V6, but require rings for DIA 66.1→73.1 mm.

Which wheels are NOT suitable for Teana J31?

Wheels with PCD 4x100 (for example, from Nissan Almera N16), 5x100 (from some Hondas), as well as wheels with DIA less than 66.1 mm without adapter rings are incompatible. Also avoid wheels with ET less than 30mm - this will increase the load on the suspension.

How to avoid mistakes when buying discs: checklist

Before purchasing new drives, be sure to follow these steps:

Additional tips:

• 🔍 Buy discs only from trusted sellers - fakes may have inaccurate PCD or ET.
• 📄 You require a certificate of conformity - this is a guarantee that the disk has passed strength tests.
• 🔧 When installing new disks, be sure to balance and check the tightening torque of the bolts (90–110 Nm).

⚠️ Attention: If you are installing disks with less ET (For example, ET25 instead of ET35), the wheel will protrude outward. This can lead to contact with the wheel arch liners when turning and increases the risk of damage to the disc on uneven surfaces.

Frequently asked questions about the Teana J31 bolt pattern

Let's look at typical situations that owners face:

Is it possible to install 5x100 disks instead of 5x114.3?

No, this is not possible without adapters. The difference is PCD amounts to 14.3 mm, and even with adapters, such a solution will be unreliable and dangerous. Adapters for changing the bolt pattern are not recommended - they increase the load on the hub and can lead to an accident.

What tires are best for 17-inch wheels?

For disks 7J×17 ET35 optimal tire size - 225/55 R17. Alternative options:

• 215/60 R17 — will increase the ground clearance by 5 mm, but will worsen handling.
• 235/50 R17 - 10 mm wider, suitable for improving grip, but may rub against the arches when fully loaded.

When choosing, focus on the load index (at least 94T) and speed (not lower H).

What happens if you install wheels with ET20 offset?

Reducing offset to ET20 will move the wheel outward by 15 mm relative to the hub. Consequences:

• The load on the wheel bearings and steering rods will increase.
• It is possible for the tire to touch the fender liner when turning or on bumps.
• Handling at high speeds will deteriorate due to changes in the rolling shoulder.

Acceptable minimum for Teana J31 — ET30 (only for sports versions with reinforced suspension).

Can spacers be used to increase the track?

Technically yes, but this solution has risks:

• Spacers thicker than 10 mm require elongated bolts, which weakens the fastening.
• The load on bearings and suspension arms increases.
• In some countries (for example, Russia), the use of spacers may be a reason for denial of an insurance claim.

If you need a wide track, it is better to choose wheels with a smaller ET (but not lower ET30).

Where to buy wheels for Teana J31: proven options

When choosing a place of purchase, focus on:

• 🏆 Official dealers Nissan - guarantee of original spare parts, but high price.
• 🛒 Specialty stores (For example, K&K>, Replica, BBS) - a wide range and the ability to select according to parameters.
• 🌍 Foreign sites (eBay, Amazon) - cheaper, but there is a risk of running into a counterfeit or long delivery.
• 🔄 Used market - only upon personal inspection and checking for runout.

Average prices for wheels for Teana J31 (2023):

• Steel 16": 8 000–12 000 ₽ per set.
• Cast 17": 15 000–25 000 ₽ (brands Enkei, Ronal).
• Forged 18": 30 000–50 000 ₽ (BBS, OZ Racing).

Before purchasing please check:

1. Availability of a certificate (for example, TR TS 018/2011 for Russia).
2. Guarantee against hidden defects (minimum 1 year).
3. Possibility of return if the discs do not fit the geometry.

💡

When purchasing used wheels, be sure to check them for runout on a special stand. Permissible deviation is no more than 0.5 mm. Also inspect for cracks (especially at the spokes) and signs of “overtightening” of the bolts (deformed holes).