Nissan NV200 bolt pattern: parameters, compatibility and selection of wheels

Minibus Nissan NV200 is a popular commercial vehicle that is actively used both in urban environments and for cargo transportation. When choosing new wheels or tires, owners are often faced with the question: what **bolt pattern** is suitable for this model? Errors in selection can lead to vibrations, accelerated wear of the suspension, or even emergency situations.

In this article we will look at all key bolt pattern parameters for Nissan NV200, including PCD, departure ET, hub diameter DIA and compatibility with drives from other models Nissan. You will also find practical advice on choosing tires, a table of original sizes and answers to frequently asked questions.

What is a bolt pattern and why is it important for the Nissan NV200

**Bolt pattern** (or PCD - Pitch Circle Diameter) is the diameter of the circle on which the holes for mounting the wheel are located. For Nissan NV200 this parameter is critical, since incorrect selection can lead to:

• 🔧 Uneven wear tires and wheel bearings.
• 🚗 Vibrations on the steering wheel when driving at speeds above 80 km/h.
• ⚠️ Unscrewing nuts while driving (in extreme cases).

Except PCD, when choosing disks you need to consider: departure (ET) - the distance from the mating plane of the disk to its center, and diameter of the central hole (DIA). For NV200 These parameters are strictly regulated by the manufacturer.

Standard bolt pattern parameters for Nissan NV200

Official data for Nissan NV200 (all generations, including restyled versions):

Parameter	Meaning	Note
PCD (bolt pattern)	4×114.3	Typical standard for many models Nissan And Renault.
ET (departure)	35–45 mm	Optimal range. A reach of 38–42 mm is considered universal.
DIA (hub diameter)	66.1 mm	Important for centering the disc. If there is a mismatch, adapter rings are used.
Mounting thread	M12 × 1.25	Standard for most passenger cars and commercial vehicles Nissan.

These parameters are relevant for all modifications NV200, including versions with petrol (HR16DE) and diesel (K9K) engines. However, there are nuances:

• 🔄 In some markets (for example, Mexico) there are versions with PCD 4×100, but this is rare.
• 🚛 Truck modifications with reinforced suspension may have different meanings ET (up to 50 mm).

Compatible with wheels from other Nissan models

Thanks to standard bolt pattern 4×114.3, wheels from other models Nissan often suitable for NV200. Here is the list of compatible cars:

• 🚗 Nissan Almera (N16, N17) - full software compatibility PCD And DIA.
• 🚙 Nissan Juke (F15) — discs with offset fit ET 38–42.
• 🚐 Nissan Note (E11, E12) - identical parameters, but check the width of the disk.
• 🚖 Renault Kangoo - compatible PCD, but may differ DIA (needs rings).

However, there are important limitations:

⚠️ Attention: Discs from Nissan Qashqai or X-Trail may not fit due to larger hub diameter (DIA 66.1 vs 67.1). Always check this parameter!

Also consider rim width:

- For tires 185/65 R15 optimal width 6J.

- For 195/60 R16 — 6.5J or 7J.

How to check disk compatibility without documentation?

Measure the distance between the centers of opposite holes (for 4 bolts) and multiply by 1.414. For example, if the distance is 81 mm, then PCD = 81 × 1.414 ≈ 114.3 mm.

Selection of tires for Nissan NV200: sizes and recommendations

The manufacturer recommends the following tire sizes for NV200:

Tire size	Disc diameter	Note
185/65 R15	15″	Standard size for most versions.
195/60 R16	16″	Optional for versions with alloy wheels.
205/55 R16	16″	Allowed, but may touch the arches when fully loaded.

When choosing tires, consider:

• ⚖️ Load Index - for commercial use minimum 91T (615 kg per wheel).
• ❄️ Seasonality — tires with markings are suitable for winter M+S or 3PMSF.
• 💨 Pressure - in an empty car 2.2 bar, when fully loaded 2.8 bar.

⚠️ Attention: Installation of tires with a profile height of less than 60% (for example, 205/50 R16) reduces comfort and can damage the rims on rough roads.

How to measure the NV200 bolt pattern yourself

If you don't have documentation, PCD you can measure it yourself. You will need a caliper or ruler. Algorithm for 4-bolt fastening:

1. Measure the distance between the centers of two adjacent holes (for example, X = 81 mm).
2. Multiply by 1.414 (root of 2): 81 × 1.414 ≈ 114.3 mm.

To check ET (departure):

1. Place the disc face down on a flat surface.
2. Measure the distance from the surface to the edge of the rim (A).
3. Turn the disk over and measure the distance to the opposite edge (B).
4. Departure is calculated using the formula: ET = (A + B)/2 – C, where C — disk width.

For DIA It is enough to measure the diameter of the central hole of the disk. If it is larger than 66.1 mm, you will need centering rings.

Common mistakes when selecting disks and how to avoid them

Owners Nissan NV200 often encounter the following problems:

1. Ignoring crash (ET) — discs with incorrect offset shift the center of gravity of the wheel, which leads to accelerated wear of the wheel bearings.
2. Using discs without centering rings - even if there is a coincidence PCD Misalignment between the hub and disc causes runout.
3. Buying tires with the wrong load rating — for commercial use 88T (560 kg) is not enough.

To avoid errors:

• 📏 Always check the parameters with Vin number car (can be checked with the dealer).
• 🔍 Check disks for availability certificates of conformity (especially used ones).
• 🛠️ After installing new disks, be sure to do wheel alignment.

⚠️ Attention: Discs with ET < 30 mm may touch the brake calipers, and with ET > 50 mm — go beyond the wheel arches, which is prohibited by traffic regulations.

FAQ: Answers to popular questions

Is it possible to install 5x114.3 disks instead of 4x114.3?

No, this is not possible without reworking the hub. Number of holes (4 or 5) is a fundamental parameter that cannot be adapted using adapters.

What wheels are suitable from Renault?

From Renault Kangoo, Clio (III generation) and Megane (II generation) suitable wheels with PCD 4×114.3 And DIA 66.1. But check the departure - y Renault it may differ.

What happens if you install wheels with a 20 mm offset?

Discs with ET 20 will greatly shift the wheel outward, which will lead to:

• Increased load on the wheel bearing.
• Possible contact of the tire with the fender liner.
• Failure to pass technical inspection (exceeding the dimensions of the vehicle).

Is it possible to drive with different wheels on the same axle?

Absolutely not! Different discs (by weight, offset or diameter) interfere with balance and controllability, which is dangerous at high speeds.

What is the maximum diameter of disks that can be installed on the NV200?

Without suspension modifications - R16. Discs R17 will require changes in ground clearance or the use of low-profile tires, which will negatively affect comfort.