Selection of rims for Nissan Qashqai 2018 - a task that requires attention to detail. An error in bolt pattern settings can lead not only to visual imbalance, but also to serious problems with handling, suspension wear and even safety. In this material we will analyze all critical parameters: from standard PCD 5×114.3 to permissible overhang values (ET) and the diameter of the central hole (DIA).

Model Qashqai J11 (second generation, restyling 2017–2021) has strict restrictions on disk compatibility, which depend on the configuration and engine. For example, versions with 1.3 DIG-T And 1.6 dCi may have different factory wheel sizes - this is often overlooked. We have collected current data from official manuals Nissan, as well as the experience of the owners, to help you avoid common mistakes.

What is a bolt pattern and why is it important for the 2018 Qashqai

Bolt pattern (or PCD — Pitch Circle Diameter) is the diameter of the circle on which the disk mounting holes are located. For Nissan Qashqai 2018 this parameter is fixed: 5×114.3. This means that the disk has 5 holes, located on a circle with diameter 114.3 mm.

Why is this critical? PCD non-compliance leads to:

  • 🔧 Uneven tightening of bolts — the disc will “lead” when moving, which will cause vibration on the steering wheel.
  • 🚗 Accelerated wear of wheel bearings — due to misalignment, the load is distributed incorrectly.
  • ⚠️ Spinning the wheels while driving - in extreme cases this can lead to an accident.

Owners Qashqai loosening bolts are often confused with ET (disc ejection) or DIA (diameter of the central hole). For example, a disc with PCD 5×112 (like some Volkswagen) can physically be screwed to Nissan, but this is strictly prohibited - the bolts will not be tightened with the required force.

💡

If you buy used wheels, check the PCD with a caliper: measure the distance between the centers of two adjacent holes and multiply by 1.051 (for 5 bolts). For Qashqai the result should be 71.3 mm (±0.1 mm).

Official bolt pattern parameters for Nissan Qashqai 2018 by trim level

Factory parameters of wheels and tires for Qashqai J11 (2018) vary depending on engine and options. Below is the data from the catalog Nissan for the European market:

Equipment / Engine Rims size (R) Disc width (J) Reach (ET, mm) DIA (mm) Tire size
Visia / 1.2 DIG-T, 1.5 dCi 16 6.5 45 66.1 215/65 R16
Acenta / 1.3 DIG-T, 1.6 dCi 17 7.0 40 66.1 215/60 R17
N-Connecta / 1.6 dCi, 1.3 DIG-T 160 hp 18 7.0 40 66.1 225/55 R18
Tekna / 1.6 dCi, 1.3 DIG-T 160 hp 19 7.5 38 66.1 225/50 R19

Important: Discs with an ET offset of less than 38 mm (e.g. ET35) may interfere with suspension components or brake calipers, especially on versions with 19-inch wheels. Before purchasing, check the clearance using sheet of paper — insert it between the disc and the caliper when turning the steering wheel.

📊 What size rims does your Qashqai 2018 have?
  • 16 inches
  • 17 inches
  • 18 inches
  • 19 inches
  • Other size

Tolerable deviations: what can be changed without risk

The manufacturer allows slight variations in parameters, but with reservations. Here's what you can change without compromising safety:

  • 🔄 Disc width: ±0.5 inches from factory (for example, instead of 7.0J can be supplied 7.5J, but not 8.0J).
  • 📏 Departure (ET): ±2 mm from recommended. For example, for ET40 let's say ET38–42.
  • ⚙️ Center Hole Diameter (DIA): must be equal or greater factory (66.1 mm). Use spacer rings for drives with large DIA.

What absolutely cannot be changed:

  • ❌ PCD - even a minimal deviation of 0.1 mm will lead to runout.
  • ❌ Disc diameter more than ±1 inch (for example, replacing R17 on R15 or R20).
  • ❌ Tire width more than ±10 mm from the recommended value (for example, instead of 215 mm put 235 mm).
What happens if you install disks with the wrong ET?

A mismatch in the offset leads to a displacement of the wheel relative to the hub. When ET less than factory (eg ET30 instead of ET40) the disc will protrude outwards, increasing the load on the bearings and suspension arms. When ET is larger than factory (for example, ET50) the wheel will “sink” inward, which can lead to friction with elements of the body or brake system. In both cases, handling deteriorates, especially at high speeds.

How to measure the Qashqai 2018 bolt pattern yourself

If you buy used wheels or are in doubt about the markings, measure the PCD yourself. You will need:

  • 📏 Caliper or ruler with a millimeter scale.
  • 🔧 A key for unscrewing the bolts (if the disk is on the car).

Instructions for 5-bolt mounting:

  1. Measure the distance between the centers of the two neighboring holes (for example 71 mm).
  2. Multiply the result by 1.051 (for 5 bolts). Get PCD: 71 × 1.051 ≈ 74.7 mm - this is radius circles.
  3. Multiply the radius by 2: 74.7 × 2 = 149.4 mm. Round to standard value − 114.3 mm (PCD 5×114.3).

Measure the PCD with a caliper|Check the offset (ET) for compliance with the configuration|Make sure that the DIA is not less than 66.1 mm|Check for cracks and deformations|Check the markings with the compatibility table

-->

To check departure (ET) use the formula:

ET = (A + B)/2 — C,

где:


A — расстояние от внутренней кромки диска до привалочной плоскости,


B — расстояние от внешней кромки до привалочной плоскости,


C — ширина диска (в мм).

Top 5 mistakes when selecting wheels for Qashqai 2018

Even experienced car owners make mistakes. Here are the most common:

  1. Ignoring DIA. Disc with DIA 73.1 mm (like BMW) will physically sit on the hub Qashqai, but without centering rings. This will lead to runout at speeds above 100 km/h.
  2. Buying discs with ET 35 for versions with R19. A low offset increases stress on the suspension and can cause friction against the caliper.
  3. Installing tires with the wrong load index. For example, for Qashqai with engine 1.6 dCi minimum index - 91T (615 kg per wheel).
  4. Using bolts of the wrong length. Standard bolt length for Qashqai 2018 — 27–30 mm. Shorter ones will not provide reliable fixation.
  5. Neglect of balancing after replacing disks. Even a new disk may have an imbalance that will show up at speed. 120+ km/h.
💡

The most dangerous mistake is using disks with PCD 5x112 (for example, from Audi or VW). They are visually similar to 5x114.3, but when installed, 4 of the 5 bolts will be tightened skewed, which will lead to the wheels self-unscrewing.

Recommendations for choosing tires for wheels of different sizes

The tire size must match the width of the rim and the axle load. For Nissan Qashqai 2018 The following rules apply:

Disk size Recommended tire width Tire profile Minimum load index
16×6.5 205–215 mm 60–65% 88T (560 kg)
17×7.0 215–225 mm 55–60% 91T (615 kg)
18×7.0 225–235 mm 50–55% 94V (670 kg)
19×7.5 225–245 mm 45–50% 98W (750 kg)

When choosing tires, consider:

  • 🌡️ Seasonality: for winter, a profile of at least 55% (For example, 215/60 R17).
  • 🚘 Speed index: for versions with 1.3 DIG-T 160 hp minimum index - V (240 km/h).
  • ⚖️ Production date: Tires older than 5 years (even new ones) lose their elasticity. Check the labeling DOT.

Example of correct selection: For disks 18×7.0 ET40 tires will fit 225/55 R18 98W (For example, Michelin Primacy 4 or Continental ContiPremiumContact 6).

💡

When switching to higher profile tires (for example, from 55% to 60%), the speedometer will lower the speed by 2-3%. To make adjustments, use online calculators or ECU firmware (only in certified centers!).

Where to buy wheels for Nissan Qashqai 2018: proven options

When purchasing discs, pay attention to:

  • 🏷️ Manufacturer: optimal price/quality ratio for brands BBS, OZ Racing, Ronal (for original parameters). Budget options - Kosei, Alutec.
  • 🛒 Place of purchase:
    • Official dealers Nissan - guaranteed compatibility, but high price.
    • Specialty stores (for example, Kolesa-Darom, BlackTyres) - wide range and testing at the stand.
    • Marketplace (eg. Avito, Drom) - only for personal verification of PCD and ET.

Average prices for new wheels for Qashqai 2018 (at the beginning of 2026):

  • Steel 16″: 8,000–12,000 RUR per set.
  • Light alloy 17″: 15,000–25,000 ₽ per piece (branded).
  • Light alloy 19″: 30,000–50,000 ₽ per piece (BBS, OZ).

⚠️ Attention: When purchasing used wheels, be sure to check them for radial and axial runout (tolerance - no more than 0.5 mm). Use dial indicator or contact a tire shop.

FAQ: Frequently asked questions about the Nissan Qashqai 2018 bolt pattern

Is it possible to install wheels from Nissan X-Trail on Qashqai 2018?

Yes, but with reservations. Nissan X-Trail T32 (2014–2021) has the same bolt pattern 5×114.3 And DIA 66.1 mm, but:

  • Discs R17 And R18 from X-Trail will fit without problems.
  • Discs R20 may not fit due to the larger diameter of the brake calipers on Qashqai.
  • Departure (ET) y X-Trail often ET35–40, which is acceptable for Qashqai, but may require checking clearances.
What is the maximum size of wheels that can be installed on the Qashqai 2018 without modifications?

Without suspension and arch modifications, maximum size:

  • 19×7.5 ET38 with tires 225/50 R19 - for versions Tekna.
  • 18×7.5 ET40 with tires 235/50 R18 - for other configurations.

To install R20 you will need:

  • Replacing wheel bearings with reinforced ones.
  • Trimming arches (illegal in Russia).
  • Use of spacers (impairs safety).
What should I do if there is vibration in the steering wheel after replacing the discs?

Causes and solutions:

  1. Unbalanced wheels — carry out balancing on a stand with laser alignment.
  2. DIA mismatch — install centering rings (cost ~500 ₽ per set).
  3. Warped disc - check for beating (tolerance - 0.3 mm).
  4. Incorrect bolt tightening - use a torque wrench (tightening torque - 110–120 Nm).
Can I use wheel spacers on a Qashqai?

Technically yes, but with serious caveats:

  • Spacers up to thickness 10 mm acceptable, but require extended bolts.
  • Spacers are thicker 15 mm increase the load on the wheel bearing by 1.5–2 times.
  • In Russia, the use of spacers not certified and may cause denial of insurance payment in case of an accident.

An alternative is disks with the correct ET.

What bolts are needed for Qashqai 2018 wheels?

Official parameters of mounting bolts:

  • Thread: M12 × 1.25.
  • Length: 27–30 mm (depending on the thickness of the disc).
  • Head type: conical (angle 60°).
  • Tightening torque: 110–120 Nm.

For wheels with spacers, use bolts on 10–15 mm longer standard