Nissan Juke bolt pattern: how to choose wheels and not make a mistake

Selection of rims for Nissan Juke - a task that requires attention to detail. An error in the bolt pattern parameters can lead to vibrations, premature wear of the wheel bearings, or even an emergency. This article will help you understand the key characteristics: PCD (fastening pitch), ET (departure), DIA (center hole) and hub diameter - for all generations of the crossover, including restyled versions.

We have collected current data for Juke F15 (2010–2019) and Juke F16 (2019–present), and also considered the nuances of selecting non-original discs. Particular attention was paid to compatibility with models Renault and other alliance cars, which often raises questions among owners. If you are planning tuning or seasonal tire changes, here you will find answers to all technical questions.

What is a bolt pattern and why is it important for Nissan Juke

Term bolt pattern (or PCD - Pitch Circle Diameter) indicates the diameter of the circle on which the disc mounting holes are located. For Nissan Juke This parameter has been standardized, but ignoring it is fraught with serious consequences. For example, a disc with the wrong PCD may:

• 🔧 Not a tight fit to the hub, causing the steering wheel to wobble at speed.
• 🚗 Deform the bolts when tightened, which leads to their breakage.
• 💥 Cause the wheel to come off in extreme conditions (sharp maneuvers, pits).

For Juke all generations the manufacturer sets PCD 5×114.3 - this means that the disk is secured with five bolts located on a circle with a diameter of 114.3 mm. However, it is important to consider other parameters: departure (ET), center hole diameter (DIA) And rim width. Their combination guarantees the safety and correct operation of the suspension.

⚠️ Attention: Discs with PCD 5×112 (for example, from Volkswagen or Audi) are visually similar, but incompatible with Nissan Juke. A difference of 2.3 mm leads to uneven tightening of the bolts and the risk of their failure.

Official bolt patterns for all Juke generations

The manufacturer clearly regulates the wheel parameters for each modification. Juke. The data below is for the basic versions and variants with an extended wheelbase (for example, Juke Nismo).

Parameter	Nissan Juke F15 (2010–2019)	Nissan Juke F16 (2019–present)	Nismo / RS
PCD (bolt pattern)	5×114.3	5×114.3	5×114.3
ET (reach), mm	35–45	35–45	30–40
DIA (central hole), mm	66.1	66.1	66.1
Bolt thread	M12×1.25	M12×1.25	M12×1.25
Recommended disc diameter, inches	16–18	17–19	18–20

For Juke F16 (second generation) it is possible to install wheels with a diameter of up to 19 inches, but this requires the selection of low-profile tires to avoid friction on the arches. An offset (ET) of less than 30 mm may result in disc contact with suspension components when the vehicle is fully loaded.

Compatible with rims of other cars

Thanks to the unification of the platform Nissan Juke Compatible with disks of a number of Alliance models Renault-Nissan-Mitsubishi. This opens up more options for tuning or budget replacement. However, it is important to check not only the PCD, but also DIA, since the center hole may vary.

• 🚘 Renault Captur (2013–present) - Fully PCD and DIA compatible.
• 🚘 Renault Kadjar — discs with ET 35–50 are suitable (check for runout required).
• 🚘 Mitsubishi ASX (until 2021) - the same as PCD, but DIA can be 67.1 mm (adapter rings are needed).
• 🚘 Nissan Qashqai J10/J11 - identical parameters, but the rim width may differ.

When using discs from Infiniti Q30 (based on the same platform) please note departure: factory wheels Q30 often have an ET of 40–45, which can narrow the track Juke and worsen handling at high speeds.

⚠️ Attention: Discs from Nissan Micra K13 (2010–2017) have PCD 4x100 - their installation on Juke technically impossible without adapters, which is strictly not recommended due to the risk of wheel imbalance.

How to measure bolt pattern yourself

If you are not sure about the disk parameters (for example, when purchasing second-hand), they can be measured without a specialized tool. You will need a caliper or ruler. Follow the algorithm:

1. Remove the wheel and clean the hub from dirt.
2. Measure the distance between the centers of two adjacent holes (for example, A).
3. Multiply the resulting value by a factor of 1.701 (for 5 holes). The result is the desired PCD.

Formula for calculation:

PCD = A × 1.701

To check DIA measure the diameter of the central hole of the disk. Deviation up to ±0.5 mm is allowed, but in this case you will need centering rings (hubs).

Measure PCD using formula|Check DIA|Check for cracks on rim|Check offset (ET) with recommended values|Check tire width compatibility-->

Tire selection: what you need to know

The bolt pattern directly affects the choice of tires. For Nissan Juke the manufacturer recommends the following combinations:

Disc diameter, inches	Wheel width, inches	Recommended tire size	Load/Speed Index
16	6.0–7.0	205/60 R16	92H
17	6.5–7.5	215/55 R17	94V
18	7.0–8.0	225/45 R18	95W
19	7.5–8.5	225/40 R19	93Y

When choosing non-standard sizes (for example, 235/40 R19), consider:

• 📏 Tire width should not exceed the width of the rim by more than 20–25%.
• 🔄 Profile height affects the operation of the odometer and ABS (deviation up to 3% is acceptable).
• ⚖️ Load Index must be no lower than the factory one (for example, 92H for 16-inch wheels).

⚠️ Attention: Installing tires with a profile height of less than 45% on 18-19 inch wheels increases the risk of wheel damage on pothole roads. For Juke with a rigid suspension this is especially true.

What is the speed index?

The speed index indicates the maximum speed at which the tire maintains its performance. For example:

- H — up to 210 km/h

- V — up to 240 km/h

- W — up to 270 km/h

For Juke minimum recommended index - H, but for versions with a 1.6 DIG-T engine (190 hp) it is better to choose V or W.

Tuning and non-standard wheels: risks and solutions

Many owners Juke They strive to make the car stand out with large wheels or an aggressive offset. However, such modifications require a balanced approach:

• 🔧 Wheels 20 inches or more possible, but will require:
• Tires with a profile of 30–35 mm (for example, 225/30 R20).
• Checks for absence of contact with calipers and arches.
• Adjustments to suspension settings (for example, shortened springs).
• 📉 Negative offset (ET < 30) expands the track, but:
• Increases the load on wheel bearings.
• May require rolling out arches.
• Affects handling (the car becomes less responsive).

For safe tuning it is recommended:

1. Use 3D modeling (for example, in the program WheelFitment) to check compatibility.
2. Consult with experts who specialize in Nissan.
3. Test the car at a testing ground after installing new wheels.

Common mistakes when choosing disks and how to avoid them

Owner experience Juke shows that most problems are associated with incorrect interpretation of parameters or trust in unscrupulous sellers. Let's look at typical mistakes:

1. Ignoring DIA: Disc with PCD 5×114.3, but DIA 56.1 mm (for example, from Toyota) will not fit tightly on the hub Juke. The solution is to use centering rings (cost ~500–1500 rub.).
2. Bolt thread mismatch: Bolts M12×1.5 (from BMW) are not suitable for Juke with M12×1.25 thread. The consequences are thread failure when moving.
3. Failure to account for departure: Wheels with ET 50+ narrow the track, which reduces cornering stability. Optimal range - ET 30–45.

To avoid errors:

• 🔍 Check the markings on the back of the disc (for example, 5J×17 ET40 DIA66.1).
• 📄 Request a certificate of conformity from the seller (especially for replicas).
• 🔧 Install wheels in a trusted service with a torque wrench.

FAQ: Answers to popular questions

Is it possible to install wheels from Renault Megane 4 on Nissan Juke?

Yes, but with reservations. Megane 4 has PCD 5×114.3 and DIA 66.1, which is the same as Juke. However, factory wheels Megane often have an ET offset of 45–50, which will narrow the track Juke by 10–15 mm on each side. This can lead to poor handling at high speeds. It is recommended to choose wheels with ET 35–40.

What happens if you use the wrong length bolts?

Bolts that are too short will not provide reliable fastening, and bolts that are too long can rest against the brake disc or caliper, causing vibrations. For Juke the optimal bolt length is 27–30 mm (taking into account the thickness of the disk). When using spacers, the length of the bolts must be increased proportionally.

What is the maximum reach you can put on the Juke Nismo?

For Juke Nismo Departure ET 30–40 is allowed. Smaller values (for example, ET 20) will require rolling out the arches and may affect the life of the suspension. It is also important to consider the width of the rim: for 8J wheels the maximum tire width is 235 mm.

Do I need to balance disks during seasonal replacement?

Yes, even if the rims were not removed from the tire. During storage, microdeformations of the rubber are possible, as well as displacement of the weights. Balancing should be carried out on a stand with motion simulation (dynamic balancing), and not static.

Is it possible to drive on cracked rims?

Absolutely not. Cracks in the disk (even micron ones) lead to its destruction under load. This is especially dangerous at high speeds or when falling into a hole. Even if the crack is not visible from the outside, check the disc on a bench or using an ultrasonic flaw detector.