Crossover Nissan Qashqai J10 The first generation, released in 2007-2013, remains a popular choice among car owners due to its reliability and practicality. However, over time, even in such a car, lighting elements need to be replaced - from headlights to interior lighting. In this article we will look at all types of lamps, used in Qashqai J10, their markings, selection nuances and step-by-step instructions for replacement.

The peculiarity of the model is the use of different types of lamps depending on the configuration and year of manufacture. For example, halogen lamps were installed in basic versions H7 for low beam, while in top versions there could be xenon options. In addition, many owners are faced with the problem of selecting lamps for fog lights (H11) or side lights (W5W), which often burn out due to vibrations or low-quality analogues. We will help you figure out which lamps are best to choose for durability and safety, as well as how to avoid common mistakes when replacing.

Types of lamps in Nissan Qashqai J10: complete list by zone

B Qashqai J10 More than 20 different lamps are used, responsible for external and internal lighting. Below is a table with the main types, their markings and areas of application. Please note that in some trim levels (for example, with xenon) the low/high beam lamps may differ.

Lighting area Lamp type Marking Quantity (pcs.)
Low beam (halogen) Halogen H7 2
High beam Halogen H1 2
Fog lights (PTF) Halogen H11 2
Side lights (front) LED/halogen W5W (or T10) 4
Tail lights (stop/side) Halogen P21/5W 4

It is important to consider that in Qashqai J10 with factory xenon (optional for top trim levels) are used gas discharge lamps D2S for low beam. Replacing them requires special equipment and adjustment of the ignition unit. Lamps are also used in the cabin C5W for illuminating the glove compartment and DE3175 for the lampshade.

When choosing lamps, pay attention to plinth And power. For example, lamps H7 have a standard power of 55 W, but some manufacturers offer options with increased brightness (up to 130%). However, such lamps may shorten the life of the headlight reflector due to increased heat generation.

📊 Which bulbs do you most often change in your Qashqai J10?
  • Low beam lamps
  • Fog lights
  • Side lights
  • Tail lights
  • Interior lighting

How to choose lamps for Qashqai J10: halogen vs LED vs xenon

The type of lamp you choose depends on your priorities: durability, brightness, or compliance with factory parameters. Let's look at the pros and cons of each option:

  • 🔦 Halogen lamps: Standard option for Qashqai J10. Cheap, but last 500-1000 hours. Suitable for driving in the city, where frequent switching on/off of lights shortens service life.
  • 💡 LED lamps: Energy efficient (80% less energy consumption) and durable (up to 30,000 hours). However, they require correct installation to avoid CAN bus errors. Not all models are certified for use in headlights.
  • ⚡ Xenon lamps: Bright light (2-3 times brighter than halogen), but expensive to replace. B Qashqai J10 Can only be installed with the factory ignition unit. Homemade xenon installation prohibited by law and faces deprivation of rights.

For Qashqai J10 Halogen lamps from premium brands remain the optimal balance of price and quality: Osram Night Breaker, Philips X-tremeVision or Bosch Pure Light. They provide 20-30% more light than standard lamps, without the risk of overheating. If you prefer LED, choose models with a certificate ECE R112 (For example, Philips LED X-tremeUltinon), but be prepared for possible wiring modifications.

⚠️ Attention: Installing LED lamps in halogen headlights without a beam corrector can blind oncoming drivers. In some countries this is a traffic violation.

For fog lights (H11) the best choice would be lamps with color temperatures 3000-4000K — they provide good visibility in fog and rain. Avoid "blue" lamps (6000K and above), as they are less able to penetrate fog and may cause an inspection claim.

Step-by-step instructions for replacing low beam lamps (H7)

Replacing low beam lamps in Nissan Qashqai J10 does not require special tools, but will require accuracy. Follow the instructions to avoid damage to the plastic elements of the headlight:

  1. Open the hood and turn off the power to the car by removing the battery terminal (negative).
  2. Remove the protective rubber cover from the back of the headlight by pulling it towards you.
  3. Disconnect the power connector from the lamp by pressing the latch.
  4. Remove the lamp from the grooves by turning it counterclockwise 90 degrees.
  5. Install a new lamp H7without touching the glass flask with your bare hands (use gloves or a cloth).
  6. Secure the lamp by turning it clockwise and connect the connector.
  7. Reinstall the rubber boot and check the operation of the headlight.

Disconnect the car from power (remove the battery terminal)

Prepare a new lamp (check H7 marking)

Wear gloves (to avoid leaving greasy marks on the flask)

Prepare a screwdriver (may be needed to remove fasteners)

Check the tightness of the rubber boot after installation-->

If the lamp does not work after replacement, check:

  • 🔌 The connector is connected correctly (sometimes the contacts oxidize).
  • 💡 Fuse integrity F37 (10A) in the mounting block.
  • 🔦 Condition of contacts in the cartridge (if necessary, clean them with alcohol).
⚠️ Attention: Poor quality lamps H7 may cause the cartridge to melt due to increased heat generation. When purchasing, give preference to brands with a warranty of at least 1 year.

For convenience, we recommend replacing lamps in pairs, even if only one has burned out. This will ensure uniform illumination and eliminate the need for repeated replacement in the near future.

Replacing lamps in rear lights: nuances and typical mistakes

Tail lights in Qashqai J10 combine several functions: dimensions, brake lights and turn indicators. To replace the lamps you will need access to the inside of the lamp through the trunk. The main difficulty lies in dismantling the casing, which is attached to plastic clips.

The lamps used in the rear lights are:

  • 🚦 P21/5W — combined brake light and clearance lamp.
  • 🔄 PY21W — turn signal lamp (orange).
  • 🚗 P21W — reverse lamp.

Replacement instructions:

  1. Open the trunk and remove the plastic trim from the canopy side (carefully pry up the clips with a screwdriver).
  2. Unscrew the two screws securing the flashlight (you may need a wrench T20).
  3. Pull the flashlight towards you and disconnect the power connector.
  4. Turn the lamp socket counterclockwise and remove it.
  5. Install the new lamp, observing the polarity (for P21/5W the correct position of the base is important).

Typical replacement mistakes:

  • 🔧 Using lamps with the wrong power (for example, P21W instead of P21/5W), which causes the fuse to blow F22 (10A).
  • 🔌 The contacts do not fit tightly, which is why the lamp may blink or not light.
  • 🔦 Installing LED lamps without resistors, which causes an error on the dashboard.
💡

Before replacing the bulbs in the rear lights, take a photo of the location of the sockets - this will help you avoid confusing them during reassembly.

Interior lamps and lighting: what you need to know

Inside Qashqai J10 Several types of lamps are used, which fade or burn out over time. Most often require replacement:

  • 💡 DE3175 — lamp for interior lighting (base BA9s).
  • 📦 C5W — Illumination lamp for the glove compartment and trunk.
  • 🚗 T10 (W5W) — dashboard lighting (in some trim levels).

To replace the courtesy lamp (DE3175):

  1. Carefully pry up the lampshade using a flathead screwdriver (start from the corner where the latch is located).
  2. Remove the lamp by pulling it towards you.
  3. Install the new lamp, making sure the contacts match.

When choosing lamps for the interior, you can use LED analogues, since they do not affect traffic safety. Popular options:

  • 🔦 Osram LEDriving W5W - for dimensions and lighting.
  • 💡 Philips LED BA9s — for the interior lamp (white or warm light).
⚠️ Attention: When replacing lamps in the dashboard (T10) disconnect the battery to avoid short circuit. Using LEDs that are too bright can cause the plastic parts to overheat.

If your instrument panel lights become dim, check not only the bulbs, but also brightness control (located on the steering column). Sometimes the problem lies in oxidized contacts or a faulty rheostat.

Frequent problems with lighting in Qashqai J10 and their solutions

Owners Qashqai J10 often encounter typical lighting-related problems. Let's look at the most common cases and ways to eliminate them:

Problem Possible reason Solution
Both low beam headlights do not light up Fuse blown F37 (10A) or relay K3 Check mounting block, replace fuse/relay
Side lights blinking Poor contact in the cartridge or oxidation of the connectors Clean the contacts, check the integrity of the wiring
"Check Bulb" error on the dashboard LED lamps are installed without resistors or the lamp has burned out Install resistors (for LED) or replace the lamp with a standard one
Dim headlights Reflectors fogged up or lamps lost brightness Dry the headlight, replace the lamps with new ones

If the headlights are foggy from the inside, this may be caused by depressurization of the housing. A temporary solution is to dry the headlight with a hairdryer (without overheating the plastic), but to completely eliminate the problem you will need to seal the seams with silicone.

Another common problem is fog lights not working. Check:

  • 🔌 Fuse F18 (15A) and relay K12.
  • 🔦 Lamp integrity H11 (sometimes one thread burns out).
  • 🚗 PTF power button on the dashboard (contacts may oxidize).
What should I do if, after replacing the lamp, it burns out again?

If a new lamp burns out quickly, the cause may be:

1. Increased voltage in the on-board network (check the generator).

2. Vibrations (especially important for lamps H11 in PTF - use lamps with a reinforced base).

3. Poor contact in the cartridge, leading to overheating.

It is recommended to install a voltage stabilizer or use lamps with increased vibration resistance (for example, Osram Ultra Life).

Review of the best lamps for Nissan Qashqai J10: rating 2026

Based on reviews from owners and tests by independent experts, we have compiled a rating of the best lamps for Qashqai J10 in different categories:

  • 🥇 The best halogen lamps H7:
    • Philips X-tremeVision +130% — maximum brightness, resource up to 450 hours.
    • Osram Night Breaker Laser — improved visibility by 150% compared to standard lamps.
  • 🥈 The best LED lamps H7 (certified):
    • Philips LED X-tremeUltinon - compliance ECE R112, color temperature 6000K.
    • Osram LEDriving HL — optimal light beam without glare.
  • 🥉 The best lamps for PTF H11:
    • Narva Range Power +110% — increased brightness for fog.
    • Bosch Pure Light — long service life (up to 1200 hours).

When choosing LED lamps, pay attention to the availability built-in driver And cooling radiator. Cheap models without cooling quickly degrade and can cause errors in the on-board system.

For the salon we recommend:

  • 💡 Philips LED BA9s — soft white light, close to daylight.
  • 🔦 Osram LEDriving W5W — compact, suitable for illuminating the glove compartment.
💡

When purchasing lamps, check for a certificate of conformity ECE (for external lighting) or SAE (for USA). Lamps without certification may not pass inspection.

FAQ: Frequently asked questions about lamps in Nissan Qashqai J10

Is it possible to install xenon in Qashqai J10 halogen headlights?

No, do-it-yourself installation of xenon in halogen headlights prohibited by law (Administrative Code of the Russian Federation, Article 12.5, Part 3). Legal xenon requires headlights with lenses and washers that were not installed on Qashqai J10 from the factory. An alternative is certified LED lamps with a light beam corrector.

Why after replacing the lamp H7 Has the light become dim?

Possible reasons:

  • Low voltage in the on-board network (check the generator).
  • Oxidation of contacts in the socket or connector.
  • A lamp has been installed with too much power, but low quality (for example, “Chinese” +150%).

Solution: clean the contacts, check the voltage with a multimeter (should be 13.8-14.4V with the engine running).

What kind of lamps W5W Better for size: halogen or LED?

LED lamps W5W preferable for several reasons:

  • Service life up to 50,000 hours (versus 1000 for halogen).
  • Lower power consumption (0.5W vs. 5W).
  • Fast switching on (instantaneously versus 0.2 s for halogen).

We recommend Philips LED W5W or Osram LEDriving W5W with a color temperature of 4000K.

How to remove the headlight on a Qashqai J10 to replace the lamp?

To completely remove the headlight:

  1. Remove the bumper (unscrew the 4 bolts from the bottom and 2 from the top, disconnect the clips).
  2. Remove the three headlight mounting bolts (two on top, one on bottom).
  3. Disconnect the power connectors and remove the headlight.
Attention: without experience, it is better not to remove the headlight completely - to replace the lamps, access from the reverse side is sufficient.

Is it possible to use lamps with higher wattage (for example, 100W instead of 55W)?

Not recommended. Lamps with power higher than standard (55W for H7) call:

  • Overheating of the headlight reflector (may melt).
  • Increased load on wiring and fuses.
  • Deterioration of the light beam (light becomes scattered).

An alternative is lamps with increased luminous efficiency (for example, Philips +130%), but with standard power.