Fog lights (PTF) for Nissan Serena C24: how to choose, install and avoid mistakes

Minivan Nissan Serena C24 (2005–2012) - a popular model among family drivers, but standard fog lights (FTL) were not installed on all trim levels. Even if they were in the basic assembly, over time the optical elements fade, crack or fail. In this article we will look at how to choose a PTF for Serena C24, which analogues are compatible with the original mounts, and how to correctly install them without the mistakes that 80% of owners make.

The peculiarity of the model is the non-standard shape of the bumper and limited space for installation. Universal PTFs are not suitable here: you need either original parts from Nissan (articles are given below), or certified analogues with adapters. We analyzed owner reviews, technical forums and service manuals to collect up-to-date information - without fluff and general phrases.

Original PTF for Nissan Serena C24: part numbers and features

Factory fog lights for Serena C24 were produced in two versions: for the Japanese/Asian markets (26510-4M000) and Europe (26510-4M001). The difference is in certification (European ones comply with the standard ECE R19) and lamp base: Asian version uses H11, in European - H8.

Important: original PTFs are included with wiring, power button and relay, but without frames of decorative overlays (their article number is 26530-4M000). If you buy used parts, check the integrity sealing rubber bands - their wear leads to fogging of the headlights and corrosion of the reflector.

• 🔹 Article number of the left PTF: 26510-4M010 (Japan) / 26510-4M011 (Europe)
• 🔹 Article number of right PTF: 26510-4M000 (Japan) / 26510-4M001 (Europe)
• 🔹 Lamp: H11 (12V/55W) or H8 (12V/35W)
• 🔹 New price: from 8,000 to 12,000 ₽ per couple (depending on the region)

Where can I find the original? Official dealers Nissan in Russia they often do not keep these parts in stock, but they can be ordered through Amayama, BuyEEparts or JDMBuySell. Delivery time is 2–4 weeks. Alternative - showdown in Japan (sites CarFromJapan, Upgarage), where the price is 30–40% lower, but the risk of running into broken or leaking headlights is higher.

PTF analogues for Serena C24: what to choose instead of the original

If the budget is limited or original headlights are not available, you can consider certified analogues. The main requirement is matching of fastenings And optical pattern (so as not to blind oncoming traffic). Below are proven options:

Brand	Article	Lamp type	Compatibility	Price, ₽
Depo	315-110101-101	H11	Full (1:1 fastening)	4 200
TYC	19-6505-00-1	H8	Requires wiring improvements	3 800
Hella	8GA 008 141-121	H11	Universal, adapters required	5 500
Bosch	1 987 302 004	H8	Only suitable with adapter H8→H11	6 100

⚠️ Attention: Cheap Chinese analogues (for example, NoName from AliExpress) often have incorrect light beam, because of which the traffic police may issue a fine under Art. 12.5 Code of Administrative Offenses (500 ₽). Please check for certification mark before purchasing E19 or E22 on the headlight glass.

If you choose LED-PTF, please note: for Serena C24 Only models with built-in stabilization driver (For example, Morimoto XB LED or Diode Dynamics SS3}). Conventional LED lamps in a halogen housing lead to overheating and melting of the plastic reflector.

PTF connection diagram for Serena C24: step-by-step instructions

B Nissan Serena C24 standard wiring for PTF is provided only in configurations Highway Star And Luxury. In all other cases, you will have to lay the wires yourself. Below is a universal connection diagram via a relay:

[Аккумулятор +12V] → [Предохранитель 15A] → [Контакт 87 реле]
[Контакт 86 реле] → [Масса]
[Контакт 85 реле] → [Кнопка ПТФ] → [Предохранитель 10A] → [Замок зажигания (контакт ACC)]
[Контакт 30 реле] → [ПТФ левая] и [ПТФ правая] (параллельно)

For installation you will need:

• 🔧 4-pin relay (12V/30A)
• 🔧 Fuses: 15A (power) and 10A (manager)
• 🔧 Wire cross-section 1.5 mm² (for food) and 0.75 mm² (management)
• 🔧 Female/male terminals and heat shrink tubes

Remove the negative terminal from the battery

Route the wiring through the technological holes in the bumper

Install the relay in the mounting block (for example, next to the fuse box)

Connect the power button in the cabin (optimally - in the panel next to the light switch) -->

⚠️ Attention: Do not connect the PTF directly to the dimensions or low beam! This will lead to circuit overload and the fuse trips F10 (10A) in the block under the hood. The correct option is a separate backlit button (article no. 25560-4M000 for the original).

If you already have a standard button, but the PTFs do not work, check:

1. Fuse integrity F22 (15A) in the cabin block.
2. Presence of voltage at the contact 85 relay when the ignition is turned on.
3. The condition of the mass on the body (often oxidizes under the bumper).

Installing PTF on Serena C24: nuances and errors

Installation of headlights begins with removing the bumper. To do this you need:

1. Unscrew the 4 bolts under the hood (10 mm).
2. Unscrew 2 screws in the wheel arches (Torx T20).
3. Disconnect the clips at the bottom of the bumper (carefully, they are fragile!).

⚠️ Attention: Do not pull the bumper by force - it is attached to the fender liners with plastic clips. If you break them, you'll have to buy new ones (90467-04M00, ~200 ₽ per piece).

After removing the bumper:

1. Try on the PTF to the standard holes. If they are missing, you will have to cut the grooves according to the template (you can download here).
2. Secure the headlights with bolts M6×20 with washers (tightening torque - 1.5 Nm).
3. Connect the connectors, pre-treating the contacts lithium grease (For example, Liqui Moly Electronic-Spray).

Typical installation errors:

• 🚫 Wrong angle: PTF should shine below the low beam line. Adjustment is done with screws on the back of the headlight.
• 🚫 Poor sealing: If the O-rings are not installed, moisture will enter the headlight and damage the reflector.
• 🚫 Ignoring polarity: When connecting back +/– lamps H11/H8 will burn out in 5–10 minutes.

Adjusting PTF: how to avoid a fine for glare

According to GOST R 51709-2001, fog lights must:

• 📏 Light up the road from a distance no more than 30 m (for Serena C24 optimal - 20–25 m).
• 📏 Have clear cut-off line (no blurred spot).
• 📏 Be included only with dimensions or low beam.

To adjust:

1. Place the car on a flat area 5 meters from the wall.
2. Draw a horizontal line on the wall with chalk at the height of the PTF centers (usually 40–45 cm from the ground).
3. Turn on the PTF and adjust the screws so that the upper limit of the light spot is 5–10 cm below the line.

⚠️ Attention: If, after adjusting the PTF, oncoming drivers are still blinded, the problem may be:

• 🔦 Wrong lamps (For example, H11 instead of H8 - they have different light temperatures).
• 🔦 Cloudy headlight glass (the solution is polishing or replacement).
• 🔦 Faulty relay (check the voltage at the contact 30 - must be 12.6V).

PTF maintenance and repair: what breaks most often

Average service life of PTF for Serena C24 - 5–7 years. Main faults:

Problem	Reason	Solution	Cost, ₽
Both headlights do not light up	Fuse blown F22 or relay	Replacing the fuse (15A), relay check	50–300
The inner surface sweats	Cracked glass or worn seal	Silicone sealing or headlight replacement	500–8 000
The light is dim	Contact oxidation or lamp wear out	Cleaning the contacts, replacing the lamp with H11 Osram Night Breaker	800–1 500
Flashes or turns off spontaneously	Poor ground or corrosion in connector	Contact cleaning, processing WD-40	200–500

To extend the life of the PTF:

• 🧹 Once every 3 months, clean the headlight glasses from dirt (use Sonax Glasreiniger).
• 💡 Change lamps in pairs - even if one burns out, the second will soon fail.
• 🔧 Check the fastenings after washing under pressure - a stream of water can knock down the adjustment.

How to restore a foggy headlight?

1. Remove the headlight and warm it up with a hairdryer (60°C) for 10 minutes.

2. Drill a 2 mm hole in the bottom and pour in 10 ml of isopropyl alcohol.

3. Rinse the inner surface with distilled water and dry for 24 hours.

4. Seal the hole with epoxy resin.

This method removes condensation in 90% of cases, but will not help with glass cracks.

PTF tuning: LED, xenon and other modifications

Many owners Serena C24 they want to improve the PTF light, but not all modifications are legal. Let's figure out what you can do and what you can't.

Allowed options:

• 🟢 LED lamps with certificate ECE R19 (For example, Philips X-tremeUltinon).
• 🟢 Halogen lamps increased power (H11 100W, but require reinforced wiring).
• 🟢 Yellow filters (improves visibility in fog, but reduces brightness by 20%).

Prohibited options (fine 500 ₽):

• 🔴 Xenon in a halogen headlight (dazzles, violates GOST).
• 🔴 LED lamps without certification (for example, Chinese COB).
• 🔴 Colored lamps (blue, green - only white or yellow).

If you decide to put LED-PTF, please note:

• 🔹 Will be required anti-glare screen (For example, Morimoto Anti-Flicker).
• 🔹 You need to replace the relay with power 40A (standard at 30A will not withstand).
• 🔹 Optics must be with projection module (For example, Depo LED Pro).

FAQ: Frequently asked questions about PTF on Nissan Serena C24

Is it possible to install the PTF from a Nissan Serena C25 on a C24?

No, the mountings and shape of the headlights are different. On C25 PTF with article number are used 26510-4M100that do not fit the bumper C24 without modifications.

Which lamps are better for PTF: H8 or H11?

Depends on goals:

• H11 (55W) - brighter, but puts more strain on the wiring.
• H8 (35W) - less blinding in fog, suitable for city driving.

For Serena C24 optimal H11 with temperature 3000K (yellow light).

Where is the PTF relay located in Serena C24?

The relay is located in interior fuse box (under the dashboard on the driver's side). It is marked as FOG LAMP RELAY and has a number 25230-4M000.

How to check if the PTFs are working without removing the bumper?

Connect the tester to the headlight connector (contact + - central, – - lateral). When you turn on the ignition and press the PTF button, there should be 12V. If there is no voltage, the problem is in the wiring or relay.

Is it possible to drive without one PTF if it is burned out?

Technically yes, but:

• Asymmetrical light reduces visibility by 40%.
• The traffic police inspector may issue a fine under Art. 12.5 (malfunction of external lighting devices).