You turned on the phone charger or connected the compressor to the outlet Nissan, but the device does not work? Most likely the problem lies in the ** fuse Power Socket** - a small but critical element of the electrical circuit. This component protects the on-board network from overloads, but often fails due to careless use or connection of powerful devices (for example, refrigerators or inverters).

In this article we will analyze in detail what the inscription means «Power Socket» on the fuse block Nissanwhere to look for this fuse in popular models (from Qashqai to X-Trail), how to check and replace it without contacting service. You will also learn which fuses are suitable for replacement, why they blow and how to avoid repeated breakdowns. The information is relevant for petrol and diesel versions, including hybrids.

What is Power Socket in Nissan and why its fuse is needed

Term «Power Socket» (literally - “power outlet”) in context Nissan indicates a standard 12-volt outlet (cigarette lighter) or additional sockets for connecting electrical equipment. In modern models there may be several of them:

  • 🔌 Main socket in the central tunnel (next to the gearshift lever).
  • 🔌 Additional socket in the trunk (for example, in Nissan X-Trail T32).
  • 🔌 220V socket (in hybrids and top trim levels, for example, Nissan Ariya).

Each socket is protected by a separate **fuse**, which:

  • 🔥 Prevents wiring from burning during a short circuit.
  • ⚡ Limits current to a safe level (usually 15–20 A for 12V sockets).
  • 🛠️ It is the “weak link” of the chain - it burns out first, saving expensive electronics.

If the fuse Power Socket burned out, the socket stops working, but the rest of the car systems (lights, multimedia) function normally. This is a key sign for diagnosis.

📊 How often do you use the socket in your car?
  • Daily
  • Several times a week
  • Rarely
  • Only on long trips

Where is the fuse located Power Socket at Nissan

The location of the fuse depends on the model and year of manufacture Nissan. Below is a table with typical installation locations for popular vehicles:

Model Nissan Year of manufacture Fuse location Denomination (A)
Qashqai J10/J11 2007–2021 Fuse box in the passenger compartment (under the steering wheel, on the left) 15–20
X-Trail T31/T32 2007–2022 Unit under the hood (main) or in the cabin (additional) 20
Juke F15 2010–2019 Cabin unit (behind the cover next to the gas pedal) 15
Navara D40 2005–2015 Unit under the hood (next to the battery) 25
Ariya 2021–present Cabin unit (under the center console) 20 (12V) / 10 (220V)

To find the fuse Power Socket, follow these steps:

  1. Open the fuse box cover (usually marked with the symbol ⚡ or inscription FUSE).
  2. Look for the inscription «Power Socket», «Cigarette Lighter» or «Acc Socket» on the back of the cover or diagram.
  3. If there is no diagram, use tweezers to check the fuses one by one with a multimeter (see next section).
💡

Some models Nissan (For example, Patrol Y62) fuse Power Socket can be duplicated - one is responsible for the front socket, the other for the rear. Check both!

How to check a fuse Power Socket without tools

If the outlet stops working, first check the fuse. To do this, it is not necessary to have a multimeter - a visual inspection is enough:

Remove the fuse with tweezers (not your fingers!)|Inspect the metal jumper - if it's blown, the fuse is bad|Compare with an adjacent fuse of the same rating|Install a new fuse (only with the same rating!)-->

Signs of a blown fuse:

  • 🔥 The jumper inside is torn or melted.
  • 🔍 The body is blackened or deformed.
  • 💡 When the device is connected to the outlet, nothing happens (there is not even a click of the relay).

If everything is visually in order, but the socket does not work, check the fuse with a multimeter:

  1. Place the meter in circuit test mode (diode or resistance icon).
  2. Touch the probes to the fuse contacts. If resistance 0 ohm - he is correct. If OL (break) - replacement required.
⚠️ Attention: Never replace a fuse Power Socket on a “bug” (wire or foil). This may cause a fire in the interior! As a last resort, use a fuse with same denomination, but not higher.

Why the socket fuse blows in Nissan: top 5 reasons

Most often the fuse Power Socket fails for the following reasons:

  1. Connecting powerful devices. Compressors, inverters (12V→220V) or refrigerators may consume current 10–15 A, which is close to the fuse limit. For example, an inverter 300 W at an efficiency of 85% it will require ~30 A from a 12V network - this is guaranteed to burn a 15-amp fuse.
  2. Short circuit in the plug. Cheap chargers or adapters with exposed contacts can short-circuit “+” and “–” in the socket.
  3. Poor contact in the connector. Oxidation or looseness of the socket leads to sparking and overheating.
  4. The socket itself is faulty. Moisture, corrosion or mechanical damage can cause a short circuit inside the housing.
  5. Incorrect fuse rating installed. For example, instead of 15 A set 5 A, and it burned out at the slightest load.

Critical error: many owners Nissan after replacing the fuse, reconnect the same device that caused the breakdown. This leads to repeated burnout and potential damage to the wiring.

How to check that it is not the fuse that has burned out, but the socket itself?

If the outlet still does not work after replacing the fuse, check the voltage at its contacts with a multimeter. When the ignition is on, there should be a light on the central contact 12–14 V, and on the side ones - 0 V (weight). If there is no voltage, the problem is in the wiring or relay.

Step-by-step instructions for replacing the fuse Power Socket

To replace you will need:

  • 🔧 Tweezers (usually included with the car).
  • 🔋 New fuse of the same rating (see table above).
  • 📸 Flashlight (to illuminate the fuse box).

Algorithm of actions:

  1. Turn off the ignition and remove the key.
  2. Locate the fuse box (see "Where is it located" section).
  3. Remove the unit cover (usually it is secured with latches).
  4. Use tweezers to remove the burnt fuse. Power Socket.
  5. Install a new fuse same denomination (for example, if there was 15 A, just put 15 A).
  6. Close the unit cover and check the operation of the outlet.

If after replacement the fuse blows again, do not repeat the procedure - this indicates a serious malfunction (short circuit in the wiring or socket). In this case, diagnostics at a car service center is required.

💡

Replacing the fuse Power Socket You can do it yourself in 2-3 minutes, but only if you use an original fuse with the correct rating.

Which fuses are suitable for replacement in Nissan

For sockets Power Socket in Nissan standard blade fuses are used (blade fuse) of the following types:

Denomination (A) Case color Size Application in Nissan
5 Orange Mini (ATM) Socket in trunk (rare)
10 Red Mini (ATM) Additional sockets (for example, in Ariya)
15 Blue Mini (ATM) Main outlet on most models
20 Yellow Mini (ATM) X-Trail, Navara, Patrol
25 White Mini (ATM) Sockets for high-power devices (e.g. NP300)

Recommendations for selection:

  • 🔹 Buy fuses from famous brands: Bussmann, Littlefuse, Hella or original Nissan (article 28510-4M000 for 15 A).
  • 🔹 Avoid cheap Chinese analogues - they may have low metal quality and burn out at the slightest load.
  • 🔹 For hybrids and electric vehicles (e.g. Leaf or Ariya) use fuses marked EV — they are designed for specific loads.
⚠️ Attention: Some models Nissan (For example, GT-R or 370Z) socket Power Socket can be protected not only by a fuse, but also relay. If replacing the fuse does not help, check the relay in the same block (usually it is marked as Power Socket Relay).

Common mistakes when working with a fuse Power Socket

Even experienced car owners make mistakes that lead to repeated breakdowns or electrical damage. Here are the most common:

  1. Using a larger fuse rating. For example, instead of 15 A put 25 A, hoping that it will “last longer.” This threatens to melt the wiring or cause a fire.
  2. Ignoring the cause of burnout. If the fuse is blown due to a faulty compressor, replacing it without repairing the device will lead to repeated failure.
  3. Checking the fuse by eye without removing it. Sometimes the jumper cracks inside, but this is not noticeable from the outside. Always remove the fuse for inspection!
  4. Connecting devices with the wrong plug. For example, using a cigarette lighter plug Sony in the socket Nissan may cause poor contact and sparking.
  5. Replacing the fuse with the ignition on. This may cause a power surge and damage the electronics.

If you doubt your actions, refer to the official manual Nissan for your model or use service documentation (for example, Nissan Consult).

FAQ: Frequently asked questions about the fuse Power Socket at Nissan

Is it possible to use a socket Power Socket to connect a refrigerator or inverter?

Theoretically it is possible, but with reservations:

  • 🔌 The maximum power of the device should not exceed 180 W (for fuse 15 A).
  • ⚡ For inverters (12V→220V) use a separate socket with a fuse 20–25 A and thick wires.
  • 🔋 Connect powerful devices only when the engine is running so as not to drain the battery.

For long trips, it is better to install an additional socket with a separate fuse and relay.

Why does the socket work after replacing the fuse, but after a while it stops working again?

This indicates intermittent short circuit. Possible reasons:

  • 🔌 Poor contact in the outlet itself (oxidation or looseness).
  • 🔋 Malfunction of the connected device (for example, a charger with a microcrack on the board).
  • 🔍 Damage to the wiring from the outlet to the fuse box.

Solution: check the socket with a multimeter in resistance mode (there should be ∞ - there is no break). If it shows 0 ohm - look for a short circuit.

Where to buy an original fuse for Nissan?

Original fuses Nissan can be purchased:

  • 🏬 In official dealerships (check the article by VIN).
  • 🛒 In auto parts stores (Autodoc, Exist, Emex).
  • 🌍 On AliExpress or Amazon (look for brands Bussmann or Littlefuse).

The cost of one fuse is from 50 ₽ (analog) up to 300 ₽ (original).

Is it possible to install an additional socket in the Nissan?

Yes, but subject to the rules:

  1. Use a socket with a fuse and relay (such as a kit Hella 8FL 009 359-031).
  2. Connect to a wire that is powered only when the ignition is on (for example, from a radio).
  3. Install the fuse 15–20 A in the block next to the new device.
  4. Wires with a cross-section of at least 1.5 mm² (for currents up to 15 A).

If you are not confident in your skills, have the installation done by an electrician.

What to do if the fuse Power Socket Does it burn out immediately after replacement?

This is a sign short circuit in the chain. Actions:

  1. Unplug all devices.
  2. Remove the fuse and check the socket for short circuit with a multimeter (the resistance between “+” and “–” should be ∞).
  3. If there is a short circuit, disassemble the socket and check it for oxidation or damage.
  4. If the outlet is OK, look for a short in the wiring from the outlet to the fuse box.

In difficult cases, contact the service department - repairing the wiring yourself without experience can lead to a fire.