Owners Nissan Juke Often faced with the need to replace wipers or carry out maintenance of their mechanism. However, the standard position of the brushes is not always convenient for such work - they can interfere with access to the fasteners or block the opening of the hood. The solution is simple: set the wipers to service position, where they rise vertically and lock into place. But how to do this correctly without damaging the electric drive or control system?
In this article we will look at all the ways to activate the service mode for Juke (including models F15 And J10), we will tell you about the nuances for cars with different types of electronics, and also provide unique data on resetting wiper errors after service. You will learn what tools you will need, how to avoid common mistakes and what to do if the brushes “curl” after returning to their working position.
What is the service position of wipers and why is it needed?
Service position is the mode in which the wipers Nissan Juke rise vertically and are fixed, freeing access to the windshield and drive mechanism. This mode is used for:
- 🔧 Replacing brushes without the risk of damaging the glass or the wipers themselves.
- 🔩 Repair or lubrication hinges and rods of the drive mechanism.
- 🚗 Car washes (to avoid accidental activation of the wipers).
- 🔍 Diagnostics malfunctions, for example, if the wipers “freeze” in one position.
On Juke The service mode is activated through a combination of actions with the ignition and the wiper control lever. It is important to understand that this mode not intended for continuous use — leaving the wipers in a vertical position for a long time can lead to overload of the spring mechanism or malfunction of the position sensor.
⚠️ Attention: On models Nissan Juke with the system Auto Wipers (automatic wipers) the service position can be reset after turning off the ignition. In this case, you will need to re-activate or disable the auto mode function in the on-board computer menu.
Preparing the car: what needs to be done before changing the wipers
Before moving the wipers to the service position, complete several mandatory steps:
Turn off the ignition and remove the key from the lock
Make sure the wiper control lever is in the OFF
Check that the hood is closed (on some models the hood sensor blocks the service mode)
Disable the feature Auto Wipers in the on-board computer settings (if available)
Prepare the tools: a flat-blade screwdriver (in case of jamming), silicone grease for the hinges-->
Pay special attention to the condition wiper fuse (usually this is a fuse F30 at 20A in the block under the steering wheel). If it is burned out, the service mode may not be activated. Also check if there is ice or snow on the windshield - this can block the movement of the wipers and cause the motor protection to trip.
On models Juke with NissanConnect (multimedia system) sometimes conflicts arise between electronic modules. If, after turning on the ignition, the wipers begin to move randomly, try resetting the system through the menu Settings → Reset → Electronics.
Once a year
Every 6 months
Only when they start to creak
Never changed-->
Step-by-step instructions: how to put the wipers in the service position
The algorithm for switching wipers to service mode depends on the year of manufacture and configuration Nissan Juke. Below is a universal instruction suitable for most models (including restyled versions 2014–2019 gg.):
Insert the key into the ignition and turn it to position
ON(without starting the engine). On models with a buttonSTART/STOPpress it once without pressing the brake pedal.Move the wiper control lever to the position
OFF(lower position).Turn off the ignition (turn the key to position
LOCKor click the buttonSTART/STOPagain).Turn the ignition back on (position
ON).During 5 seconds move the wiper lever to position
MIST(one short-term switching on) and immediately return it toOFF.Wait until the wipers rise to the vertical position and stop. This will take about 3-5 seconds.
If the wipers do not respond, repeat steps 3–6 again. On vehicles with Intelligent Key (keyless entry) may require holding a button START/STOP in position ON longer than 2 seconds.
What to do if the wipers don't go up?
If after 3-4 attempts the wipers do not move to the service position, check:
1. **Fuse status** (usually F30 in the fuse box under the steering wheel).
2. **Connecting the connectors** of the wiper motor (they may oxidize or become disconnected).
3. **Operability of the wiper relay** (relay K30 in the same block).
4. **Presence of errors in the system** (use a diagnostic scanner or reset errors through the menu NissanConnect).
If the problem persists, the wiper gear motor or body electronics control unit may be faulty (BCM).
Features for different generations of Nissan Juke
The design of the wipers and their control algorithm differ depending on the generation Juke. The table below summarizes the key differences:
| Generation | Years of manufacture | Method for activating service mode | Features |
|---|---|---|---|
| Juke F15 (first generation) | 2010–2014 | Classic circuit (ignition → MIST → OFF) | On models with Bose The audio system may experience delays in operation due to the load on the on-board network. |
| Juke F15 (restyling) | 2014–2019 | The lever must be held in position MIST 2–3 seconds |
Possible conflicts with the system Around View Monitor (360° camera). |
| Juke J10 (second generation) | 2019–present | Activation via menu Settings → Maintenance → Wipers |
Confirmation required on the media screen. The service position is reset automatically after 10 minutes. |
On Juke J10 (2019+) the process is simplified thanks to the digital interface, but there is a caveat: if there is a malfunction in the system (for example, a rain sensor error), the service mode menu may be blocked. In this case, resetting the settings will help. BCM via diagnostic connector OBD-II.
⚠️ Attention: On hybrid versions Juke (For example, Juke Hybrid 2020+) the wiper service position may conflict with the regenerative braking system. Before activating the mode, make sure that the car is on a level surface and the parking brake is on.
Common mistakes and how to avoid them
Even experienced owners Nissan Juke Sometimes they make mistakes when moving the wipers to the service position. Here are the most common ones:
- ⏳ Lever shifting too quickly - if you do not maintain a pause between turning on the ignition and pressing
MIST, the system may not respond. - 🔋 Low battery — if the on-board network voltage is low, the wiper motor may not receive enough power to enter service mode.
- 🌧️ Automatic wiper mode enabled - on models with
Auto WipersYou must first disable this feature. - 🔧 Trying to forcefully raise the wipers manually - this can damage the gear drive of the gear motor.
If, after successfully moving to the service position, the wipers “curl” (do not return to their original state), perform the following steps:
- Turn off the ignition and wait 30 seconds.
- Turn the ignition back on and move the lever to the
OFF. - If the wipers do not move, briefly (for 1 second) switch them to
LOW(first speed).
If the wipers operate jerkily after returning from the service position, lubricate the plastic bushings on the mounting axis with silicone grease. This will eliminate squeaking and extend the life of the mechanism.
How to return wipers to working position
After completing the work, the wipers must be returned to their standard position. To do this:
- Turn on the ignition (position
ON). - Briefly (for 1–2 seconds) turn the wipers to
MIST. - Wait until they return to the down position and stop.
- Turn off the ignition.
On Juke J10 (2019+) return to the working position occurs automatically after:
- Start the engine.
- Exceeding the speed of 10 km/h (if the car starts moving).
- Manual reset via menu
Settings → Maintenance.
⚠️ Attention: If, after returning, the wipers continue to “twitch” or stop in an arbitrary position, this may indicate a malfunction wiper position sensor (Hall sensor) or a break in the motor power supply circuit. In this case, diagnostics using a scanner is required Consult-III+ or similar.
Diagnosis of faults after maintenance
If after replacing the blades or repairing the wipers do not work correctly, perform diagnostics using the following algorithm:
| Symptom | Possible reason | Solution |
|---|---|---|
| The wipers don't move at all | Fuse blown F30 or the relay is faulty K30 |
Check and replace fuse/relay. If the problem persists, diagnose the gear motor. |
| The wipers move jerkily | Gear wear or insufficient lubrication of joints | Disassemble the mechanism, clean and lubricate the rubbing parts. If the teeth are worn, replace the motor. |
| Wipers do not stop in down position | The position sensor is faulty or the calibration is lost | Perform calibration via Consult-III+ or reset settings BCM. |
Automatic mode (Auto Wipers) doesn't work |
Rain sensor dirty or open circuit | Clean the sensor (located by the rear view mirror). Check the connector and wiring. |
To reset errors in the wiper system to Nissan Juke You can use the following method (without diagnostic equipment):
- Turn off the ignition.
- Disconnect the battery terminal for 10 minutes.
- Reconnect the terminal and perform the procedure for activating the service mode again.
If after all the manipulations the wipers continue to work incorrectly, the cause may be a software failure in the unit BCM. In this case, the module must be reflashed at a service center.
FAQ: Frequently asked questions about Nissan Juke wipers
Is it possible to leave the wipers in the service position overnight?
No, standing in a vertical position for a long time may cause deformation of the spring mechanism or malfunction of the position sensor. The maximum recommended time is 1–2 hours.
Why did the wipers start squeaking after replacing the blades?
The creaking is usually caused by improper installation of the brushes (loose fit to the glass) or lack of lubrication on the mounting axis. Check brush compatibility with your model Juke and apply silicone grease to the plastic bushings.
How to reset the wiper error on the dashboard?
On most versions Juke The error can be reset by following the following sequence:
- Turn on the ignition.
- Move the wiper lever three times to the
MISTwith an interval of 1 second. - Turn off the ignition and wait 30 seconds.
If the error remains, diagnostics via OBD-II.
Will wipers from Nissan Qashqai fit on Juke?
No, despite the external similarity, the fastenings and length of the brushes are different. For Juke (depending on the year) length brushes are used 26"/16" (660/406 mm) or 24"/16" (610/406 mm). Check the size in the instruction manual.
What to do if the wipers are frozen to the glass?
Do not try to force them on - this may damage the motor. Instead:
- Pour warm water (not boiling water!) onto the windshield or use a defroster.
- Carefully separate the brushes from the glass using a plastic scraper.
- After defrosting, move the wipers to the service position and lubricate the axles.