Tail light of <em>Nissan Tiida</em>: disassembly, lamp replacement and repair

Nissan Tiida is a popular compact car that is valued for its reliability and practicality. However, even such cars eventually develop problems with lighting, especially with the rear lights. Dim brake lights, burnt-out headlight bulbs or cracks in the ceiling light - all this not only spoils the appearance, but also creates the risk of a fine or an accident.

In this article we will figure out how to replace the tail light yourself with Tiida (including models C11 And C13), we will select the right lamps according to the article numbers, and also tell you about the nuances of repairing lampshades and contacts. You'll learn what tools you'll need, how to avoid mistakes during disassembly, and when it's best to call an electrician.

Rear light device Nissan Tiida: circuits and components

Tail light Tiida consists of several key elements:

• 🔦 Housing — plastic base with fastenings to the body.
• 💡 Lamps — are responsible for brake lights, dimensions, turn signals and reverse gear.
• 🔌 Lampshade (diffuser) - a transparent or tinted cover that protects the lamps.
• 🔗 Electrical connector — connects the headlight to the on-board network.

On models Tiida C11 (2004–2012) and C13 (2012–2019) the design of the lamps is similar, but there are differences in the mounting of the lampshade and the type of lamps. For example, in C13 LED brake lights are often used, and in C11 - classic halogen. Below is a table with the main components:

Component	Tiida C11 (2004–2012)	Tiida C13 (2012–2019)
Brake lamp type	P21/5W (halogen)	P21/5W or LED module
Reversing lamp	P21W	P21W or W16W
Mounting the lampshade	4 plastic latches	2 latches + 2 screws
Power connector	2-pin (standard)	3-pin (with separate positive for LED)

⚠️ Attention: On Tiida with factory LED lights (C13 after 2015) you cannot install halogen lamps - this will lead to an error on the dashboard and overheating of the lamp.

What kind of lamps are in the rear light? Nissan Tiida: articles and analogues

The choice of lamps depends on the year of manufacture and vehicle equipment. The table below shows the original articles and popular analogues:

Function	Lamp type	Original article	Analogues (brands)
Brake light / Clearance	P21/5W	26500-JD00A (Nissan)	Osram 2825, Philips 12972PR, Bosch 1987302075
Reverse	P21W	26530-JD00A	Narva 48338, Hella 8GP 003 631-001
Turn signal	PY21W (yellow)	26520-JD00A	GE Lighting 50740, MTF Light 12V21W
Fog light	P21W	26540-JD00A	Koito P21W, IPF 12V21W

For Tiida C13 with LED stops, original modules are supplied under the article number 26500-4M01A (right side) and 26500-4M00A (left). Their average price is 8,000–12,000 rubles per pair. Budget analogues: Depo or TYC, but their build quality is worse.

💡 Advice: When purchasing lamps, pay attention to plinth And power. For example, a lamp P21/5W has two contacts (for stop and clearance), and PY21W — orange glass for the turn signal.

Step-by-step instructions: how to remove the tail light on Nissan Tiida

To replace the lamps or shade, you will need to remove the lamp. The process takes 15–20 minutes and does not require special skills. You will need:

• 🔧 Phillips screwdriver (PH2).
• 🔨 Plastic spatula or flat screwdriver (for latches).
• 🧤 Gloves (so as not to leave prints on the lampshade).

Sequence of actions:

1. Open the trunk and remove the trim from the canopy side (it is secured with clips).
2. Disconnect the electrical connector by pressing the latch.
3. On Tiida C11 press out the 4 plastic latches around the perimeter of the lamp. On C13 additionally unscrew 2 screws with a Phillips screwdriver.
4. Carefully pull the flashlight out, do not pull on the wires!

⚠️ Attention: On models with rear view camera (optional for C13) the flashlight connector is connected to the camera wire. Do not pull on it - you may damage the cable!

Disconnect the negative terminal of the battery|Remove the trunk trim|Prepare tools|Take a photo of the location of the connectors-->

Replacing lamps in the rear light: nuances and errors

After removing the flashlight, replacing the bulbs takes 2–3 minutes. The main thing is not to touch the glass of halogen lamps (grease marks lead to overheating). Algorithm:

1. Turn the lamp socket counterclockwise and pull it out.
2. Remove the burnt out lamp and install a new one (without any force!).
3. Return the cartridge to its place and secure it.

Critical error: using high power lamps (for example, 35W instead of 21W). This leads to melting of the lampshade and a short circuit.

If the lamp does not light after replacement, check:

• 🔋 fuse - on Tiida The fuse is responsible for the brake lights F35 (10A) in the block under the steering wheel.
• 🔌 Contacts — oxidation or breakage in the connector.
• 🔧 Mass — poor contact with the body (clean the light attachment point).

What to do if the lamp constantly burns out?

The cause is most often power surges or a bad ground. Install a voltage stabilizer (for example, Nippon or Shuft) or check the generator - the normal voltage in the on-board network should be 13.8–14.4V.

Repair of the rear light bulb: polishing, painting, sealing cracks

The lampshade (diffuser) becomes cloudy over time from the sun or cracks from impacts. You can restore it in several ways:

1. Polishing - Removes minor scratches. Use:

• 🧴 Pasta 3M 09374 or Meguiar’s PlastX.
• 🔴 Polishing machine (at low speed) or hand sponge.

2. Painting - if the lampshade has turned yellow. Suitable paint for plastic Dupli-Color (article DPH1600). Degrease the surface before painting White spirit.

3. Sealing cracks - temporary solution. Use:

• 🔥 Epoxy glue (For example, Loctite Epoxy).
• 🔳 Clear tape (only for small chips).

⚠️ Attention: If the crack goes through the entire lampshade, it is better to replace it - the sealing will not restore the tightness, and moisture will get inside, which will lead to corrosion of the contacts.

Problem	Solution	Cost (RUB)
Cloudy lampshade	Polishing	300–800 (materials)
Cracks	Sealing with glue	200–500
Yellowing	Painting	600–1 200
Severe damage	Replacing the lampshade	1 500–4 000

Frequent malfunctions of rear lights Nissan Tiida and their reasons

Owners Tiida often encounter the following problems:

1. Brake lights don't light up

• 🔋 Fuse blown F35.
• 💡 The lamp has failed (especially if one side does not work).
• 🔌 Broken wire or oxidation of contacts in the connector.

2. Dimensions flash

• 🔄 Bad weight on the body (clean the light attachment point).
• 🔋 Unstable voltage in the on-board network (check the generator).

3. Water inside the lantern

• 🌧️ Crack in the lampshade or seal.
• 🚗 The drain hole in the trunk is clogged (on Tiida C13 it is located under the lantern).

💡 Advice: If the lights fog up after washing, remove them and dry them with a hairdryer. Then apply silicone grease to the seal.

Where to buy spare parts for the tail light Nissan Tiida: original vs analogues

Spare parts for flashlights Tiida can be purchased at the following places:

• 🏢 Official Nissan dealers - guarantee of original parts, but prices are 30–50% higher.
• 🛒 Online stores (Exist.ru, Autodoc, Kolesa-darom) - a wide selection of analogues.
• 🔧 Showdown - a budget option, but without a guarantee (the price of a used flashlight is 2,000–5,000 rubles).

Comparison of original and non-original parts:

Detail	Original (Nissan)	Analog (Depo, TYC)
Lampshade (diffuser)	RUB 3,500–5,000	1,200–2,500 rub.
Lantern body	6,000–8,000 rub.	2,000–4,000 rub.
LED brake light module	8,000–12,000 rub.	3,000–6,000 rub.

⚠️ Attention: When buying analogues, check articles and compatibility with your modification Tiida. For example, flashlights for C11 And C13 not interchangeable!

FAQ: Frequently asked questions about taillights Nissan Tiida

Is it possible to install LED lamps instead of halogen ones?

Yes, but only if you have Tiida C13 Factory prepared for LED (3-pin connector). On C11 It will be necessary to modify the wiring or install resistors, otherwise there will be an error on the panel.

How to check if the reverse lamp is working?

Turn the ignition on, put the car in neutral and have a helper look at the lights while you put the car in reverse. If the lamp does not light, check the fuse F20 (10A) and contacts.

What to do if the light is cracked after an accident?

If the crack is small, you can seal it with epoxy glue. In case of severe damage, it is better to replace the lampshade or the entire lamp. The cost of a new lampshade is from 1,500 rubles, a used one – from 800 rubles.

Why are my brake lights dim?

Reasons: oxidation of contacts, low voltage in the network (check the generator) or installation of low-quality lamps. Try cleaning the contacts and replacing the lamps with original ones.

Do I need to remove the bumper to replace the headlight?

No, on Tiida The lights can be removed without removing the bumper. It is enough to unscrew the fastenings from inside the trunk.