Nissan Terrano: how much oil is in the engine (table by year and engine)

Question how much oil is in the engine Nissan Terrano occurs among owners of this crossover every time they change the lubricant. Errors in volume or choice of oil can lead to engine oil starvation or, conversely, to excess pressure, which is fraught with leaks through the seals. The problem is especially acute for models with motors K9K (1.5 dCi) and MR20DE (2.0 l), where overfilling or underfilling is critical for the life of the turbine and timing chain.

In this article you will find exact data on oil volume for all versions Terrano (including restyled ones), recommendations on viscosity and brands, as well as step by step instructions to check the level. We will analyze the nuances for gasoline and diesel engines, point out common mistakes when replacing them, and give tips on saving money without damaging the engine. If you're planning a DIY replacement, here's everything you need to do it right the first time.

Official data: how much oil is in a Nissan Terrano engine by engine

Oil volume in Nissan Terrano depends on the engine type, year of manufacture and even configuration. For example, for diesel K9K 1.5 dCi (90 or 110 hp) required 4.3–4.5 liters, while gasoline MR20DE 2.0 "will take" up to 4.8 liters with a complete replacement with filter. Important: these figures are relevant for dry engine (for example, after a major renovation). During a standard change, some of the oil remains in the system, so you need to fill in 200–300 ml less.

Below is a table with data from Nissan service manuals for models Terrano R51 (2014–2020) and Terrano R20 (for Asian markets). Please note that for vehicles with automatic transmission (variator Jatco) an additional check of the oil level in the automatic transmission may be required - this is a separate procedure.

Engine model	Volume, l	Power, hp	Years of manufacture	Oil volume (with filter), l	Recommended viscosity
K9K 792/796 (1.5 dCi)	1.5	90–110	2014–2020	4.3–4.5	5W-30, 5W-40 (ACEA C4)
MR20DE (2.0)	2.0	137–144	2014–2020	4.6–4.8	5W-30, 5W-40 (API SN)
H4M (1.6)	1.6	114	2017–2020 (select markets)	4.2–4.4	5W-30 (ILSAC GF-5)
K9K 800 (1.5 dCi, 150 hp)	1.5	150	2018–2020 (restyling)	4.7–4.9	0W-30, 5W-30 (Low SAPS)

⚠️ Attention: For engines K9K with particulate filter (DPF) it is mandatory to use class oils Low SAPS (low content of sulfated ash, phosphorus and sulfur). Ignoring this requirement leads to filter clogging and expensive repairs.

If your Terrano equipped Start/Stop system, the manufacturer recommends oils with improved low-temperature properties (for example, Total Quartz INEO ECS 5W-30). For regions with frosts below –30°C, the use of viscosity is allowed 0W-30 or 0W-40.

How to check the oil level in a Nissan Terrano: step-by-step instructions

Checking the oil level in Nissan Terrano - a procedure that many owners perform incorrectly. Errors lead to false readings: for example, if the engine is not warmed up or the car is parked on a slope, the dipstick will show the wrong level. Here correct algorithm:

1. Warm up the engine to operating temperature (the temperature indicator arrow should be in the middle zone).
2. Turn off the engine and wait 5–7 minutes — the oil should drain into the pan.
3. Place the car on flat surface (a slope of more than 2° will distort the result).
4. Remove the dipstick, wipe it with a clean cloth and insert it back until it stops.
5. Remove the dipstick again and check the level: it should be between the marks MIN And MAX.

⚠️ Attention: On diesel Terrano (especially with a motor K9K 1.5 dCi) oil level may falsely rise due to fuel getting into the crankcase (faulty injectors or fuel injection pump). If the oil smells like diesel fuel or its level rises without topping up, immediately diagnose the fuel system!

For accuracy check use original Nissan dipstick (catalog number 15811-ED00A). Non-original dipsticks may have incorrect markings, which will lead to overfilling or underfilling.

Warm up the engine to operating temperature|

Wait 5-7 minutes after stopping|

Make sure the car is level |

Use a clean, lint-free cloth for the dipstick|

Repeat the check 2 times for accuracy-->

What kind of oil to pour into Nissan Terrano: manufacturer's recommendations and alternatives

Manufacturer Nissan recommends for Terrano oils that meet standards API SN (for gasoline engines) and ACEA C4 (for diesel engines). However, in practice the choice depends on climatic conditions, mileage and driving style. For example:

• 🌡️ For cold climate (below –25°C): Mobil 1 ESP 0W-30 or Liqui Moly Top Tec 4200 5W-30.
• 🏙️ For city driving (frequent traffic jams): Castrol Edge 5W-40 (resistant to high temperatures).
• 🛣️ For long trips: Motul Specific 913C 5W-30 (extends the replacement interval).
• 🔧 For used engines more than 150,000 km: Valvoline MaxLife 5W-40 (with additives for worn out engines).

For diesel Terrano with particulate filter (DPF) oils with a high ash content (for example, API CJ-4). They will quickly clog the filter, which will lead to emergency mode and expensive repairs. Optimal choice - Total Quartz INEO ECS 5W-30 or Shell Helix Ultra ECT C3.

If you prefer original Nissan oils, please note:

• Nissan Strong Save X 5W-30 (for gasoline engines).
• Nissan Eco Save 5W-30 (for diesel engines with DPF).

Original Nissan|

Mobil 1 / Castrol|

Liqui Moly / Motul|

Other (I'll write in the comments)|

Common mistakes when changing oil and how to avoid them

Even experienced car owners make mistakes when changing oil. Nissan Terrano. Here are the most common ones and how to prevent them:

1. Incomplete drainage of old oil. If you do not remove the pan or flush the system, up to 10–15% of the waste remains in the engine, which reduces the life of the new oil. Solution: Use a vacuum pump to pump out or remove the pan (new gasket required, part no. 11136-ED00A).
2. Oil overflow. In engines MR20DE And K9K overflowing by 300–500 ml leads to foaming and damage to the seals. Solution: Pour oil in 100 ml portions, checking the level with a dipstick.
3. Using a non-original filter. Cheap filters (for example, from Framm or Mann-Filter fakes) may not withstand pressure, which leads to oil starvation. Solution: Buy filters with catalog numbers 15208-ED00A (original) or Mann W712/94 (high-quality analogue).
4. Ignoring flushing. When switching from one type of oil to another (for example, from mineral to synthetic), flushing is required. Solution: Use Liqui Moly Oil-Schlamm-Spulung or Wynn’s Oil System Cleaner.

⚠️ Attention: On diesel Terrano after changing the oil it may light up error P0299 (low boost pressure). This is due to oil entering the intercooler through the turbine. If an error appears, check the condition of the turbine and oil lines.

What happens if you mix different oils?

Mixing oils of different brands or viscosities may result in precipitationclogging the oil channels. It is especially dangerous to mix mineral And synthetic oils - this causes coagulation of additives and loss of lubricating properties. In emergency cases, it is allowed to add oil of the same standard (for example, ACEA C4), but not more than 10% of the total volume. After this it is required complete replacement with flushing.

Oil change intervals: when to change and why you shouldn’t delay

Official regulations Nissan recommends changing the oil Terrano every 15,000 km or once a year. However, these figures are relevant for ideal conditions: European roads, high-quality fuel, moderate climate. In the realities of the CIS, the interval should be shortened:

• 🏙️ City riding (traffic jams, short trips): 10,000 km.
• 🛣️ Long trips (constant engine load): 12,000 km.
• ❄️ Extreme frosts (below –30°C): 8,000–9,000 km.
• 🏗️ Dusty roads (primers, construction zones): 7,000–8,000 km.

On diesel Terrano with particulate filter (DPF) oil ages faster due to soot ingress. If you often drive short distances (less than 10 km), the replacement interval should be reduced to 7,000–8,000 km, even if the mileage is short.

⚠️ Attention: If you are using LongLife oils (For example, Castrol Edge LongLife 5W-30), do not extend the drain interval without analyzing the oil. In Russian conditions, additives in such oils lose their properties after 10,000–12,000 km.

Changing the oil yourself: step-by-step instructions with photos

Changing the oil in Nissan Terrano - a procedure that can be performed independently if you have the tools. You will need:

• 🔧 Key on 14 mm (for drain plug).
• 🔧 Oil filter puller (for example, Kingo KN-6001).
• 🛢️ Container for processing (volume no less than 5 liters).
• 🧻 Rags and gloves.
• 🔧 New oil filter (see article number above).
• 🛢️ Oil (see table for volume).

Step by step instructions:

1. Raise the car on a lift or drive it into a viewing hole. Important: Use wheel chocks!
2. Remove the crankcase protection (if equipped) - it is secured with 4-6 bolts.
3. Place a container under the drain plug (it is located on the pan, closer to the rear of the engine).
4. Unscrew the plug with the key to 14 mm and wait until the oil is completely drained (10–15 minutes).
5. Replace plug o-ring (article 11026-01M02).
6. Remove the oil filter using a puller. If it gets stuck, pierce it with a screwdriver and unscrew it like a lever.
7. Lubricate the rubber ring of the new filter with oil and tighten it by hand (do not use the tool!).
8. Tighten the drain plug to a torque 30–35 Nm.
9. Fill in 80% of required volume oil through the filler neck, then add along the dipstick.
10. Start the engine, run for 1-2 minutes, then check the level and top up if necessary.

⚠️ Attention: After changing the oil in Terrano with diesel engine K9K may catch fire error P0087 (low pressure in the fuel system). This is due to air getting into the injection pump. To eliminate the error, turn on the ignition several times without starting the engine (10 seconds each).

What to do if you have overfilled or underfilled the oil

Errors with oil volume in Nissan Terrano - not uncommon. Let's look at both scenarios and how to resolve them.

If you overfilled the oil:

• 🔧 Drain off excess through drain plug (carefully unscrew it a few turns).
• 🔧 Pump out the oil through filler neck syringe with tube (diameter 6–8 mm).
• ⚠️ Don't drive with overflow! This leads to foaming, loss of pressure and damage VVT (variable valve timing systems).

If you haven't added enough oil:

• 🛢️Add oil same brand and viscosity in small portions (50–100 ml), checking the level with a dipstick.
• ⚠️ If the oil goes away faster than usual (more than 1 liter per 1,000 km), check:
• 🔍 Condition crankshaft and camshaft seals.
• 🔍 Leaks through valve cover gasket (article 11044-ED00A).
• 🔍 Oil consumption per frenzy (typical for engines with mileage >200,000 km).

⚠️ Attention: On petrol Terrano with motor MR20DE oil consumption up to 0.5 l per 1,000 km is considered normal (according to the service bulletin Nissan NTB14-079). However, if the flow rate exceeds this figure, diagnostics are required oil scraper rings And PCV valve.

FAQ: Frequently asked questions about oil in Nissan Terrano

Can I use 10W-40 oil instead of 5W-30?

For most engines Nissan Terrano oil 10W-40 not recommended as it has a higher viscosity at low temperatures. This may lead to increased wear during a cold start. An exception is regions with hot climates (above +35°C), where the use of 10W-40 or 15W-40 for diesel engines.

How often should you check the oil level?

Check the oil level every 1,000 km or before long trips. On diesel Terrano with a mileage of more than 100,000 km, control is needed every 500 km — these engines are prone to oil waste. Use electronic probe (if installed) or classic mechanical.

What oil to pour into a Nissan Terrano with a mileage of 200,000 km?

For engines with high mileage, oils with increased viscosity and anti-wear additives:

• Liqui Moly Hochleistungs Getriebeoil 75W-90 (for manual transmissions).
• Valvoline MaxLife 10W-40 (for gasoline engines).
• Mobil Delvac MX 15W-40 (for diesel engines).

Also pay attention to oils with molybdenum (for example, Motul 8100 X-cess 5W-40), which restore microcracks in the metal.

Do I need to flush the engine when changing the oil?

Flushing is required in the following cases:

• 🔄 When switching from one type of oil to another (for example, from semi-synthetic to synthetic).
• 🛑 If the oil is heavily contaminated (darkened, contains metal shavings).
• 🚗 After purchasing a used car (service history unknown).

For rinsing use soft compounds (For example, Wynn’s Oil System Cleaner), avoid “five-minute” flushes - they are aggressive for oil seals.

Why does the pressure light come on after changing the oil?

If after changing the oil the light on the dashboard lights up pressure lamp (red oil can), the reasons may be as follows:

• 🔧 Oil pump faulty (typical for motors K9K with mileage >150,000 km).
• 🔧 Oil filter clogged (especially if a non-original filter was used).
• 🔧 Insufficient oil level (check with a dipstick).
• 🔧 Pressure sensor faulty (article 25080-ED00A).

If the lamp flashes at idle, but goes out when the speed increases, the problem is worn oil pump or clogged oil pickup screen.