Owners Nissan Sunny - one of the most popular sedans in the history of the Japanese automobile industry - sooner or later you have to deal with replacing wheels. And if everything is more or less clear with the choice of tires, then the parameters of the disks often raise questions. The main one: what kind of bolt pattern does Nissan Sunny have?? An error in this parameter can lead to vibrations, uneven tire wear and even accidents.

In this article we will look at all key parameters: from standard PCD 4×100 to permissible overhang values (ET) and the diameter of the central hole (DIA). You will also find a compatibility table with other models Nissan And Almera, tips on selecting non-original discs and answers to frequently asked questions. We will pay special attention to generations B13, B14 And B15 — their parameters may differ!

What is a bolt pattern and why is it important for Nissan Sunny

Bolt pattern (or PCD — Pitch Circle Diameter) is the diameter of the circle on which the mounting holes of the wheel rim are located. For Nissan Sunny For most generations, this parameter is fixed: 4×100. This means that the disk is mounted on 4 bolts, and the distance between the centers of opposite holes is equal to 100 mm.

But why is this parameter so critical? The fact is that even a minimal PCD mismatch (for example, an attempt to install a disk with a bolt pattern 4×114.3) will lead to:

  • 🔧 Incorrect wheel alignment — the disk will “lead” to the side, which will cause the steering wheel to wobble.
  • 🚗 Uneven tire wear — the protector will wear off in spots.
  • ⚠️ Risk of wheel separation at high speed - Bolts or nuts may become loose due to improper load distribution.

In addition to PCD, when selecting disks for Sunny important to consider:

  • 📏 Departure (ET) — the distance from the mating plane of the disk to its center. For Sunny usually ET35–ET45.
  • ⭕ Center Hole Diameter (DIA) - must coincide with the hub. Standard for Sunny: 59.1 mm.
  • 🔩 Mounting type - bolts M12×1.25 or nuts (depending on the year of manufacture).
⚠️ Attention! There are often "universal" PCD drives on the market. 4×100/114.3, where the holes have elongated grooves. Such disks not recommended for Nissan Sunny — they do not provide rigid fixation and can deform under load.

Nissan Sunny bolt pattern by generation: B13, B14, B15

Wheel rim parameters for Nissan Sunny vary depending on generation and market (Japan, Europe, Asia). Below is a table with exact data for the most common versions:

Generation Years of manufacture PCD (bolt pattern) ET (reach), mm DIA (hub), mm Recommended drive size
Nissan Sunny B13 1990–1994 4×100 35–45 59.1 13×5.0–6.0, 14×5.5–6.5
Nissan Sunny B14 1994–1998 4×100 38–45 59.1 14×5.5–6.5, 15×6.0–7.0
Nissan Sunny B15 (Japan) 1998–2004 4×100 35–40 59.1 14×5.5–6.5, 15×6.0–7.0
Nissan Sunny B15 (Europe, Almera N16) 1998–2006 4×114.3 35–45 66.1 15×6.0–7.0, 16×6.5–7.5

Please note: European versions Sunny B15 (sold as Almera N16) have another loose bolt — 4×114.3. This is due to the unification of the platform Nissan for the European market. If you are the owner of such a car, the wheels are from Japanese Sunny to you won't fit!

It is also worth considering that some sports versions (for example, Sunny GTi-R) could be equipped with wheels with a non-standard offset (ET30) and width 7J. Before purchasing, always check the details on your vehicle's placard (usually located on the driver's door pillar or in the glove compartment).

📊 What generation of Nissan Sunny do you have?
  • B13 (1990–1994)
  • B14 (1994–1998)
  • B15 (1998–2004)
  • Almera N16 (European Sunny)
  • I don't know

Wheel compatibility: which Nissan models are suitable for Sunny

If you are looking for alternative drives for your Sunny, you can consider options from other models Nissan with a similar bolt pattern. However, there are nuances here: even if the PCD and DIA are the same, they may differ departure (ET) or rim width, which will affect handling and suspension wear.

The table below shows models whose disks theoretically suitable for Sunny (but require checking for specific parameters):

Model Nissan PCD DIA, mm Notes
Micra K11/K12 4×100 59.1 Suitable for Sunny B13/B14, but the width of the disks is usually narrower (5.0–6.0J).
Almera N15 4×100 59.1 Fully compatible with Sunny B14.
Pulsar N14/N15 4×100 59.1 Similar parameters, but check the offset (options are possible ET30–45).
Primera P10/P11 4×114.3 66.1 Only for European Sunny B15 (Almera N16).

You can also consider wheels from other Japanese brands with bolt patterns 4×100:

  • 🚗 Toyota Starlet (EP82, EP91) - but with caution: there may be a crash ET35–50.
  • 🚗 Mazda 121 (JA) - matches PCD and DIA, but the width of the discs is often narrower.
  • 🚗 Honda Civic (EG, EK) - only if DIA is bored to 59.1 mm.
⚠️ Attention! Installation of discs with non-standard offset (ET) changes the load on the wheel bearings and suspension arms. For example, if you install a disk with ET20 instead of ET40, the wheel will protrude outward, which will lead to:

  • Accelerated wear of bearings (2–3 times faster).
  • Deterioration of controllability at high speeds.
  • Possible contact of the wheel with the arch when the steering wheel is turned completely.

How to correctly measure the bolt pattern of a Nissan Sunny yourself

If you are not sure about the parameters of your Sunny (for example, a car after restyling or with a non-standard suspension), you can measure the bolt pattern yourself. You will need:

  • 📏 Caliper or ruler.
  • 🔧 Key for removing the wheel (if you measure on a removed disk).

Method 1: Measuring between hole centers

  1. Remove the wheel and place the disc on a flat surface.
  2. Measure the distance between the centers of the two neighboring holes (for example L = 70 mm).
  3. For 4×100 multiply L by 1.414 (root 2). We get PCD: 70 × 1.414 ≈ 99 mm (±1 mm error is acceptable).

Method 2: Measuring between the edges of the holes

  1. Measure the hole diameter (D).
  2. Measure the distance between the edges of adjacent holes (L).
  3. PCD = L + D (for 4 holes).

To check the diameter of the center hole (DIA) use a caliper - measure the inner diameter of the hub window on the disc.

Measure PCD (should be 100mm for most versions)

Check DIA (59.1 mm for B13/B14, 66.1 mm for European B15)

Ensure that the overhang (ET) does not exceed 35–45 mm

Check the width of the rim (no more than 7J for standard suspension)

Assess the condition of the hub bolts (M12×1.25 thread)

-->

What wheels and tires are recommended for Nissan Sunny

Selecting wheels and tires for Sunny depends on driving style, climatic conditions and vehicle modification. Below are recommendations for different scenarios:

Standard sizes (factory equipped):

  • 🔄 Sunny B13/B14: disks 14×5.5J, tires 175/70 R14 or 185/65 R14.
  • 🔄 Sunny B15 (Japan): wheels 15×6J, tires 185/60 R15.
  • 🔄 Almera N16 (Europe): wheels 15×6.5J, tires 195/55 R15.

Alternative options (taking into account permissible deviations):

  • 🚘 To improve handling: wheels 15×7J ET38 with tires 195/50 R15 (but check the ground clearance!).
  • ❄️ For winter: narrow wheels 14×5.5J with tires 175/70 R14 (snow passes better).
  • 🏁 For tuning: wheels 16×7J ET35 with tires 205/45 R16 (requires rolling out arches).

When choosing tires, pay attention to load index (for Sunny usually 82T or 86H) and speed index (not lower T for city driving). Recommended for winter tires Q or T.

⚠️ Attention! Installing discs wider than 7J on standard suspension Sunny may lead to:

  • The wheel hitting the fender liner when the steering wheel is turned completely.
  • Accelerated wear of wheel bearings (due to increased force leverage).
  • Failure to pass technical inspection (if the disk width exceeds the permissible limit by more than 1 inch).

1. Condition of the threads of the mounting holes (there should be no “licked” edges).

2. No cracks on the spokes (especially on alloy wheels).

3. Disc geometry - ride it on a balancing machine: runout of more than 0.5 mm is unacceptable.-->

Common mistakes when selecting wheels for Nissan Sunny

Even experienced car owners sometimes make mistakes when choosing wheels. Here are the most common mistakes and their consequences:

  1. Ignoring the DIA parameter

    If the center hole of the disc is larger than that of the hub, the wheel will be mounted on centering rings. This is a temporary solution - during intense driving, the rings may become wrinkled, which will lead to vibrations. For Sunny B13/B14 DIA should be exactly 59.1 mm without adapters!

  2. 1-2mm PCD misalignment

    For example, trying to install a disk with PCD 4×98 (from some Volkswagen) instead 4×100. As a result, the bolts will not be tightened evenly, which will lead to the “eight” of the disk after 500–1000 km.

  3. Installing discs with the wrong offset

    Discs with ET20 (for example, from Honda Civic Type-R) visually look aggressive, but will shift the wheel axle outward. This will increase the load on the wheel bearing by 1.5–2 times and reduce its service life to 20–30 thousand km.

  4. Using bolts of the wrong length

    Bolts are too long (M12×1.5 instead of M12×1.25) may rest against the brake disc, and short ones will not provide sufficient fixation.

To avoid mistakes, always check the parameters with the data:

  • 📄 On the car sign (on the door pillar or in the glove compartment).
  • 🔧 In the catalog of original spare parts Nissan (by VIN code).
  • 🛠️ On the websites of trusted disc manufacturers (for example, BBS, Enkei, Kosei).
What to do if you bought wheels with the wrong bolt pattern?

If the drive has a 4x114.3 PCD instead of 4x100, it can be re-drilled (bored holes). However, this will weaken the structure and make the disc unsuitable for intensive driving. An alternative is to use eccentric bolts (such as from Hubcentric), but they must be certified and installed by a specialist. In any case, this approach is considered a temporary solution!

Where to buy wheels for Nissan Sunny: original vs analogues

The market offers many disc options for Sunny - from original to budget replicas. Let's look at the pros and cons of each option:

1. Original Nissan wheels

  • ✅ Perfect match of all parameters (PCD 4×100, DIA 59.1, ET40).
  • ✅ Manufacturer's warranty (usually 2-3 years).
  • ❌ High price (from 8,000 rubles for a stamped disc).
  • ❌ Limited selection of designs.

2. Discs from trusted brands (BBS, Enkei, Kosei)

  • ✅ Alloy wheels weigh 20-30% less than the original ones, improving dynamics.
  • ✅ Wide selection of designs (from classics to tuning options).
  • ✅ The price is lower than the original (from 4,000 rubles per disc).
  • ⚠️ Risk of running into a fake (check the certificates!).

3. Budget analogues (Replica, Tech-Line)

  • ✅ Price from 2,500 rub. per disc.
  • ❌ There are often deviations in geometry (beating, inaccurate ET).
  • ❌ Low quality paint (corrosion after 1-2 winters).

4. Used wheels

  • ✅ The price is 2-3 times lower than new ones.
  • ⚠️ Risk of hidden defects (cracks, curvature).
  • ⚠️ Worn mounting holes (bolts may spin).

Where to look:

  • 🛒 Official dealers Nissan - for original discs.
  • 🌍 Online stores: KolesaDarom, ShinaGuide, AutoDisk.
  • 🏗️ Local tire shops - often there are used options in good condition.
  • 📱 Avito, Drom - to search for rare or tuning wheels.
💡

When purchasing wheels for Sunny, be sure to request a certificate of conformity (especially for alloy wheels). Discs without a certificate may not pass inspection and pose a danger in an accident.

FAQ: Frequently asked questions about the Nissan Sunny bolt pattern

Is it possible to install wheels from Nissan Almera on Sunny B14?

Yes, but only if it Almera N15 (1995–2000) with bolt pattern 4×100. Discs from Almera N16 (2000–2006) have PCD 4×114.3 and will not fit without adapters.

What bolts are needed for Sunny B13 wheels?

Standard parameters: M12×1.25, length 25–28 mm (depending on the thickness of the disc). Alloy wheels may require tapered bolts (60°).

What happens if you install wheels with ET20 instead of ET40?

The wheel will move outward by 20 mm, which:

  • It will increase the load on the wheel bearing (the service life will be reduced by 2–3 times).
  • It can cause the wheel to touch the arch when the steering wheel is turned completely.
  • It will worsen handling at high speeds (the car will become “shafty”).

Such an overhang is only permissible when modifying the suspension (installing spacers, reinforced arms).

Will wheels from Toyota Corolla E120 fit Sunny B15?

No. U Corolla E120 bolt pattern 5×100, and Sunny B15 — 4×100 (or 4×114.3 for European versions). Even adapters will not solve the problem due to the different number of holes.

What is the maximum size of disks that can be installed on the Sunny without modifications?

For most versions:

  • B13/B14: 15×7J ET38 with tires 195/50 R15 (may rub when fully loaded).
  • B15: 16×7J ET35 with tires 205/45 R16 (requires rolling out arches).

To install disks 17" and above you will need:

  • Replacing shock absorbers with shortened ones.
  • Rolling or cutting arches.
  • Replacing wheel bearings with reinforced ones.