Rear wiper <em>Nissan Note E11</em>: complete replacement and repair guide

Rear wiper on Nissan Note E11 - a small but critical element, especially in rainy weather or winter. Its malfunction can turn a trip into real torture: stains on the glass, creaking, or even complete failure of the mechanism. Owners Note E11 (2006–2013) are often faced with brush wear, motor failure or traction breakage - and even if even a beginner can cope with replacing the brush, repairing the drive will require knowledge and tools.

In this article we will look at all aspects of the rear wiper operation on Nissan Note E11: from choosing original and analog brushes to electrical and mechanical diagnostics. You will learn how bypass the typical problem with the wiper sticking in the up position (typical for cars after 2010), what errors lead to premature wear of parts, and why sometimes it is enough to simply clean the relay contacts. The material is supported by diagrams, compatibility tables and answers to frequently asked questions - all so that you can solve the problem without a service station.

Rear wiper device Nissan Note E11: diagram and principle of operation

Rear wiper on Note E11 is a simple but coherent system of three key components:

• 🔧 Electric motor (motor) - located under the plastic panel in the trunk, responsible for rotating the shaft.
• 🔗 Traction and leverage - transmit movement from the motor to the wiper. Often break due to corrosion or mechanical stress.
• 🧹 Wiper blade - a rubber element that directly cleans the glass. Wears out every 6–12 months.

When the wiper is activated through a lever under the steering wheel or a button on the panel, a signal is sent to body control module (BCM), which turns on the motor relay. Next, the mechanism converts the rotational movement of the shaft into the rocking movement of the lever. Important: on Note E11 there is no separate fuse for the rear wiper - it is protected by a common fuse F37 (10A) in the mounting block.

Where is the rear wiper relay located?

Rear wiper relay Nissan Note E11 located in the additional relay box under the glove compartment (to the right of the passenger's feet). It is marked as R17 and is responsible for supplying power to the motor. When diagnosing, check the relay contacts - oxidation or weak contact can simulate an engine malfunction.

Feature Note E11 — lack of a wiper position sensor (unlike the front wipers). This means that the motor always returns the lever to its original position according to the timer, and not according to the actual position. That is why, when the mechanism jams, the wiper can stop in an arbitrary place, and not go into the “parking” position.

Typical faults: why the rear wiper does not work

If the rear wiper is on your Nissan Note E11 stopped working, creaks or moves jerkily, the reasons can be divided into three categories:

1. Mechanical breakdowns:
   • 🔩 Worn or broken traction (the plastic hinge often breaks).
   • 🛠️ Motor shaft jamming due to corrosion or dirt.
   • 🧊 Freezing of the mechanism in winter (if the wiper is not put in a warm place).
2. Electrical problems:
   • 🔌 Broken wiring or oxidation of contacts (especially at the point of transition of the harness from the trunk to the body).
   • 🔋 Motor malfunction (winding burnt out or brushes worn out).
   • 📱 Relay failure R17 or control unit BCM.
3. Problems with the brush:
   • 🧽 Rubber wear (stains appear, does not clean well).
   • 🔗 Breakage of the brush attachment to the lever.

The most common malfunction is broken plastic rod (part with catalog number 28550-JM00A). It is made of brittle plastic that will crack over time, especially if the wiper frequently operates in winter conditions. The second most common problem is oxidation of motor contacts. This is easy to check with a multimeter: when the wiper is on, there should be a 12V.

⚠️ Attention: If the wiper is stuck in the up position and does not return down, don't try to move it with your hand - this can break the motor gear teeth. First turn off the power (by removing the fuse F37), and then carefully check the mechanism.

How to replace the rear wiper blade yourself

Replacing the brush is the simplest procedure that any owner can handle. Nissan Note E11. You will need:

• 🔧 New brush (original 28520-JM00A or analogues: Bosch 3397004646, Denso 550-0109).
• 🔨 Flat screwdriver (for prying off the retainer).
• 🧴 Silicone grease (optional, to extend service life).

Step by step instructions:

1. Raise the wiper arm perpendicular to the glass (to the “replace” position).
2. Press the latch at the base of the brush (located on the side) and remove the old brush.
3. Install the new brush until it clicks. Make sure it locks - pull it towards you.
4. Lower the lever onto the glass and check the operation of the wiper.

If the new brush squeaks, apply it to the rubber part. silicone grease (not to be confused with WD-40!). This will reduce friction and extend service life. Also check that the wiper arm is not bent - this can lead to uneven pressure of the wiper blade on the glass.

Mechanical repair: replacement of linkage and wiper arm

If, when you turn on the rear wiper, you hear the sound of the motor running, but the lever does not move, most likely the rod is torn. On Note E11 This is a common problem due to brittle plastic. To replace you will need:

• 🔧 New traction (28550-JM00A or equivalent Febi 28550).
• 🔨 Set of screwdrivers (phillips, flat).
• 🔗 Pliers (for removing retaining rings).
• 🧴 Lithol or other grease.

Repair algorithm:

1. Remove the plastic lining in the trunk (it is secured with 4 clips and 2 screws).
2. Disconnect the motor connector and remove it by unscrewing the 3 mounting bolts.
3. Remove the retaining ring from the motor shaft and carefully remove the old rod.
4. Install the new link, aligning the splines with the shaft. Secure with a locking ring.
5. Lubricate all moving joints and reassemble the mechanism in reverse order.

If the linkage is intact, but the wiper moves with difficulty, check lever condition. It may be bent or rusted where it attaches to the shaft. In this case, the lever can be straightened or replaced (cat. no. 28530-JM00A).

Electrical diagnostics: motor, relay, wiring

If the wiper does not respond to being turned on, first check fuse F37 (10A) in the mounting block (located to the left of the steering wheel under the cover). If it is intact, proceed to diagnosing the electrical circuit:

element	How to check	Normal indicators
Relay R17	Test with a multimeter in diode mode. When submitting 12V contacts 85 and 86 should be triggered by short circuits 30 and 87.	Winding resistance: 70–90 ohms
wiper motor	Connect directly to 12V (minus on the body, plus on the connector contact).	It should rotate smoothly, without squeaks.
Wiring	Ring the circuit from the relay to the motor. Pay attention to the connector in the trunk (often oxidizes).	Circuit resistance: close to 0 ohm
Power button	Ring the button contacts in the "On" position. (on the lever under the steering wheel or on the panel).	Closed resistance: 0 ohm

A common problem is oxidation of contacts in the motor connector. To clean them:

1. Disconnect the connector from the motor.
2. Process contacts alcohol solution or a special cleaner (Contact Cleaner).
3. Apply to contacts conductive lubricant (For example, Liqui Moly Electronic-Spray).

⚠️ Attention: If the wiper motor is burned out, do not buy cheap analogues without a brand. They often have a weak gearbox that breaks after 1–2 months. Optimal options: original 28500-JM00A or Valeo 698559.

Prevention and care: how to extend the life of your rear wiper

To avoid breakdowns, follow simple rules:

• 🌧️ in winter Before parking, put the wiper in a warm place (for example, lift the lever vertically). This will prevent the mechanism from freezing.
• 🧼 Wash your glass and brush regularly special car shampoo (not household chemicals!). This will remove abrasive particles that wear down the rubber.
• 🔧 Lubricate every six months motor roller And traction connections silicone grease.
• 🚗 Do not turn on the wiper if there is ice or snow on the glass - this creates an excessive load on the mechanism.

Also note brush quality. Cheap models made of hard rubber quickly erase the glass, leaving micro-scratches. The best choice is brushes with graphite coating (For example, Bosch Aerotwin), which retain elasticity longer.

How to properly wash the rear window?

Use a soft sponge and wax-free car shampoo. After washing, wipe the glass with microfiber - this will remove any residual detergent that can corrode the rubber of the brush. Do not use ice scrapers on dry glass!

Repair cost: original spare parts vs analogues

Prices for spare parts for rear wiper Nissan Note E11 vary depending on the manufacturer. Below is a table with current proposals (for 2026):

Detail	Original (Nissan)	High-quality analogue	Budget analogue
Wiper blade	28520-JM00A 1 200–1 500 ₽	Bosch 3397004646 800–1 000 ₽	Finwhale BW320 300–400 ₽
Wiper rod	28550-JM00A 2 500–3 000 ₽	Febi 28550 1 800–2 200 ₽	Patron PT28550 1 200–1 500 ₽
wiper motor	28500-JM00A 4 500–5 500 ₽	Valeo 698559 3 500–4 000 ₽	Krauf KR28500 2 500–3 000 ₽
Wiper lever	28530-JM00A 1 800–2 200 ₽	Meyle 2853000000 1 500–1 800 ₽	Sat ST28530 900–1 200 ₽

Cost of replacement work in the service:

• Brush replacement: 200–500 ₽.
• Replacement of rod/lever: 1,500–2,500 RUR.
• Motor replacement: 2,000–3,500 ₽.

If you decide to repair it yourself, savings will be 50–70%. For example, replacing a rod will cost 1,800 ₽ (analog) + 0 ₽ (labor), instead of 4,000–5,000 ₽ in service.

FAQ: Frequently asked questions about the rear wiper Nissan Note E11

The wiper works, but leaves streaks. What to do?

Smudges appear due to wear on the rubber of the brush or contamination of the glass. Try:

1. Wash the glass degreaser (For example, Sonax Glass Cleaner).
2. Wipe the brush alcohol solution to remove fat deposits.
3. If it doesn’t help, replace the brush with a new one with graphite coating.

The wiper is stuck in the up position and will not go down. How to fix it?

This is a typical problem when the traction breaks or the motor jams. Follow the steps:

1. Turn off the fuse F37to avoid short circuit.
2. Remove the trunk lining and check the integrity of the linkage.
3. If the rod is torn, replace it (instructions above).
4. If the rod is intact, check the motor: it may be jammed due to corrosion.

Do not try to force the lever down - this may break the gearbox!

Is it possible to use a frameless brush instead of a standard one?

Theoretically yes, but there are nuances:

• 🔹 Frameless brushes (for example, Bosch Aerotwin) fit the glass lighter and better, but their fastening must fit the lever Note E11 (size U-hook 9x3).
• 🔹 They are less resistant to icing, so they may work worse in winter.
• 🔹 Before purchasing, check the length - it should be 300–320 mm.

How to check if the wiper motor is working without removing it?

Do this with a multimeter:

1. Remove the connector from the motor (it is located in the trunk).
2. Switch the multimeter to voltage measurement mode (20V DC).
3. Turn on the wiper and measure the voltage at the connector: it should be 12V.
4. If there is voltage, but the motor does not work, it has burned out.
5. If there is no voltage, the problem is in the wiring, relay or button.

Where to buy spare parts for a rear wiper Nissan Note E11?

Original and high-quality analogues can be found:

• 🛒 Official Nissan dealers - guarantee of authenticity, but high price.
• 🌍 Online stores: Exist.ru, Autodoc, Emex - wide range and reviews.
• 🏬 Local auto parts stores — check by VIN or catalog number.
• 🔄 Showdown - cheaper, but without a guarantee (risk of buying a worn-out part).

Always check when purchasing catalog number and compatibility with your year of manufacture Note E11 (2006–2013).