Owners Nissan Note are often faced with the need to replace or upgrade the interior mirror - be it installing an illuminated mirror, a rear view camera or rain sensors. The main problem with this: Are the standard wires suitable? for new equipment, and how to connect them correctly so as not to burn the car’s electronics. In this article we will look at the nuances of wiring in Nissan Note (including restyled versions E11 And E12), compatibility of mirrors from other models Nissan (For example, Micra or Juke), and also give step-by-step instructions, taking into account typical mistakes.

We will pay special attention pinout of connectors - where to get food +12V, how to find ground, and why you can’t connect to the rear lighting wires. We will also consider modification options: from simple mirror replacement to integration with the system Around View Monitor (if it is included in the package). For clarity, we present diagrams, compatibility tables and real cases of owners.

Which mirrors are suitable for Nissan Note on fastening and wiring

Standard interior mirror in Nissan Note attached to the ceiling three-point bracket with threaded holes. Diameter of mounting bolts - M6, the distance between them depends on the year of manufacture:

  • 🔧 Note E11 (2004–2012): 120 mm between the outer bolts, the central one is shifted 10 mm to the left.
  • 🔧 Note E12 (2012–2020): 130 mm, symmetrical arrangement.
  • 🔧 Note Acenta/tekna (with sensors): additionally there is a connector for connection Rain Sensor.

By wiring mirrors from the following models are compatible Nissan (with reservations):

  • 🚗 Micra K13 (2010–2017) - identical power connector, but the wires may not be long enough.
  • 🚗 Juke F15 (2014–2019) - suitable for mounting, but requires an adapter for backlighting.
  • 🚗 Pulsar C13 — full compatibility in terms of connectors, but the mirror is 2 cm wider.

Important: mirrors from Qashqai or X-Trail won't fit - they have a different power connector (6-pin instead of 4-pin in Note) and other arrangement of fastenings. Also avoid mirrors with Auto-Dimming (automatic dimming) from Teana or Maxima - they require connection to CAN buswhat's in Note not provided.

📊 What kind of mirror are you planning to install?
  • Backlit
  • With rear view camera
  • With rain sensor
  • Ordinary, but with a better view
  • Other

Pinout of the standard mirror connector in Nissan Note

In the ceiling Nissan Note provided 4-pin connector (white) for connecting a mirror. Its location is under the ceiling trim, next to the place where the mirror is mounted. To get to it, carefully pry up the plastic trim with a screwdriver (remove the sun visors first).

Contact Wire color Purpose Voltage
1 Red +12V (permanent) 12.6V (with engine running)
2 Black Weight (GND) 0V
3 Yellow +12V (with ignition on) 12.6V (only with ACC/ON)
4 Green Signal from the rain sensor (if available) 0–5V (analog)

⚠️ Attention: If your configuration does not include a rain sensor, the green wire may not be connected to the control unit. Connect power to it it's impossible - this will lead to an error B2601 (precipitation sensor malfunction).

For illuminated mirrors, use red (+12V constant) And black (mass). If the backlight should work only when the ignition is on, take the power from yellow wire. The rear view camera will require an additional wire to the radio (usually orange with a black stripe - reverse gear signal).

Step-by-step instructions for connecting a new mirror

Before starting work, turn off negative battery terminal (key to 10 mm) and wait for the capacitors to discharge (5–10 minutes). This will prevent short circuits when working with wires.

Remove sun visors (unscrew 2 Torx T20 screws)

Disconnect the power connector from the standard mirror (press the latch)

Check the voltage on the contacts with a multimeter (20V DC mode)

Prepare new wires (cross-section not less than 0.75 mm²)

Insulate all twists with heat shrink or electrical tape-->

Next, follow the algorithm:

  1. Remove the old mirror: unscrew the 3 mounting bolts (you may need an extension for the key). If the mirror is glued, carefully cut it with a knife after heating it with a hairdryer.
  2. Connect power:
    • 🔌 For illuminated mirror: red → +12V, black → mass.
    • 🔌 For the camera: additionally extend the wire to the radio (use corrugation for protection).
  • Check polarity: connect the mirror to the battery outside the car. If the backlight does not light, change it + And – in some places.
  • Install a new mirror: secure it with bolts (tightening torque - 1.5 Nm) and connect the connector. Check the operation of all functions.

    • ⚠️ Attention: If, after connecting the mirror with the camera, the image on the radio screen upside down, check the polarity of the video signal. In some cases it is necessary to change places video+ And video– in the connector RCA.

    💡

    Use silicone grease for the rubber seals of the new mirror - this will prevent squeaks when driving over uneven surfaces.

    Compatibility of mirrors with the system Around View Monitor

    In top trim levels Nissan Note Tekna (since 2015) all-round viewing system is provided Around View Monitor. If you install a mirror with a camera, it must support digital signal (not analog RCA), otherwise the image will not appear on the display.

    For integration you will need:

    • 📱 Mirror with connector FAKRA (For example, Nissan OEM 28510-4M00A).
    • 📱 Adapter FAKRA → RCA (if you connect to a non-standard radio).
    • 📱 Software activation of the camera in the radio menu (path: Settings → Camera → Rear View → Enable).

    Critical nuance: if your car does not have a standard camera, connect the mirror with Around View will require laying a new cable from the radio to the trunk (for the rear camera) and installing additional sensors in the bumpers. Without this, the system will not work correctly.

    Mirror model Compatible with Around View Required adapter
    Nissan 28510-4M00A Yes (full) No
    Aftermarket with RCA Partial (rear view only) FAKRA → RCA
    Micra K13 OEM Yes (with wiring modifications) Soldering wires

    Common mistakes and how to avoid them

    Mistake #1: Connecting to the lampshade wires. Many owners try to take power from the interior lamp, but this leads to the fact that the mirror illumination only works when the doors are open. Correct: use red wire from the standard connector.

    Mistake #2: Ignoring polarity. If you confuse + And –, the LEDs in the mirror will burn out immediately. Always check with a multimeter before connecting.

    Mistake #3: Using twists without soldering. Inside Nissan Note wires are subject to vibration. Twists oxidize over time - use soldering iron or crimp terminals.

    What should I do if the mirror does not work after installation?

    1. Check the fuse F37 (10A) in the interior block - it is responsible for the mirror circuit.

    2. Measure the voltage at the connector: if not +12V, the problem is in the wiring to the fuse box.

    3. If the mirror with the camera is not displayed, check the radio settings: in some firmware you need to manually select the camera type (NTSC/PAL).

    4. For mirrors with Auto-Dimming connection required CAN bus (pins 6 and 14 in the diagnostic connector).

    Selecting wires and installation tools

    To connect the mirror, use stranded copper wires cross section:

    • 🔌 0.75 mm² - for illumination and power supply of the camera.
    • 🔌 1.0 mm² — if you connect additional sensors.

    Recommended Tool:

    • 🛠 Multimeter (for example, Mastech MS8229).
    • 🛠 Soldering iron (power 40–60 W) with solder POS-61.
    • 🛠 Crimp terminals "mom-dad" (pitch 2.54 mm).
    • 🛠 Corrugation for wiring (diameter 6–8 mm).

    To lay wires from the mirror to the radio, use regular channels:

    1. Remove the windshield pillar trim (it is held on by clips).
    2. Route the wire along the left post, securing it with zip ties.
    3. Route the wire under the instrument panel and connect it to the radio connector (usually connector A24, pin 12 - video input).
    💡

    Never lay wires under the driver's floor mat - they will rub against foot movement and may cause a short circuit.

    FAQ: Frequently asked questions about mirrors in Nissan Note

    Is it possible to install a mirror from Nissan Juke without modifications?

    No, you will need an adapter for the backlight, since the power connector is in Juke has a different key. Also a mirror from Juke 3 cm wider, which may make it difficult for the driver to see.

    How to connect a mirror with a rain sensor if it was not included in the package?

    You need to stretch the green wire from the mirror connector to the climate control unit (connector C107, pin 23). You will also need to activate the function via a diagnostic scanner (for example, Launch X431).

    Why is there no image on the radio screen after installing the mirror with the camera?

    Possible reasons:

    1. Incorrect polarity of video signal (try changing + And – on the connector RCA).
    2. The camera function is inactive in the radio settings (you need to enable Rear Camera).
    3. Incompatible signal format (for example, the camera outputs PAL, and the radio is waiting NTSC).

    Which mirror is better to choose for Nissan Note E11 with minimal modifications?

    Optimal options:

    • 🔹 Nissan OEM 28510-4M00A - full compatibility, but expensive.
    • 🔹 Aftermarket "Car Purpose" (article CP-NOTE-01) - budget analogue with backlight.
    • 🔹 Mirror from Micra K13 — requires lengthening the wires by 15 cm.