Selection of disks for Nissan Note the first generation, released in 2008, requires careful attention to technical parameters. Many owners mistakenly believe that just knowing the diameter and width is enough, but a mismatched bolt pattern can lead to serious safety problems. Bolt pattern - this is a critical parameter that determines the compatibility of the disk with the vehicle hub.
Owners Nissan Note E11s often face the need to replace cast or stamped wheels due to corrosion or mechanical damage. The wrong choice can cause the steering wheel to wobble, accelerated wear of the bearings and even the loss of the wheel while driving. To avoid these risks, you must thoroughly review your vehicle's factory specifications.
Basic parameters of the Nissan Note 2008 bolt pattern
The key parameter when choosing wheels for Nissan Note 2008 release is the number of mounting holes and the diameter of the circle on which they are located. For this model the standard diagram is 4x100. This means there are four 12mm diameter holes located on a 100mm diameter circle.
In addition to the number of bolts, the diameter of the center hole (CO) is critical. U Nissan Note of the first generation this parameter is 60.1 mm. If you buy universal wheels, then be sure to use adapter rings (spacers) to compensate for the difference in diameter and avoid vibration.
- π₯ Mounting diagram: 4x100 (4 holes, diameter 100 mm)
- π₯ Center hole diameter: 60.1 mm
- π₯ Bolt/nut thread: M12x1.25
Ignoring these numbers when ordering wheels through an online store may result in you simply not being able to put the wheel on the hub. Even a slight deviation of millimeters makes installation impossible without the use of adapters, which reduce the overall rigidity of the structure.
β οΈ Attention: The use of wheels with a bolt pattern of 4x114.3 or 5x114.3 without special spacers is strictly prohibited! This will lead to instant destruction of the hub and loss of the wheel.
Disc offset and its effect on the suspension
Disc overhang parameter, denoted as ET, determines the distance from the mating plane of the disk to the central axis of the wheel. For Nissan Note 2008 factory offset varies from 35 to 45 mm. Deviation from this value changes the running-in arm and the load on the wheel bearings.
If you install wheels with a shorter offset (for example, ET25), the wheel will protrude far beyond the arch. This not only looks aggressive, but also puts additional stress on the suspension arms. In turn, too much offset (ET50) can lead to friction between the disc and the shock absorber or brake caliper elements.
- β Recommended range: ET35 β ET45
- β Tolerance: Β±2 mm from factory value
- β Minimum departure: ET30 (only with spacers)
When choosing winter rims, you are often tempted to take a wider rim. However, remember that the width of the rim also affects the choice of offset. A wide disc with the wrong offset can touch the body when the steering wheel is turned completely or on bumps.
- Alloy wheels
- Stamped discs
- Forged wheels
- Alloy wheels
Allowable width and diameter of disks
Factory equipment Nissan Note 2008 provides for the installation of wheels with a diameter of 14, 15 or 16 inches. The rim width is usually 5.5 or 6.0 inches. These sizes are perfectly balanced for standard tires and provide a comfortable ride on city roads.
Owners are often interested in the possibility of installing wheels with a diameter of 17 inches. Technically this is possible, but it requires the selection of low-profile tires, which will worsen comfort and cross-country ability. In addition, on 17-inch wheels, the risk of damage to the disc increases when falling into a deep hole.
Below is a table of wheel and tire size compatibility for this model:
| Disc diameter | Rim Width (J) | Departure (ET) | Tire size |
|---|---|---|---|
| 14 inches | 5.5J | 35-45 | 165/65 R14 |
| 15 inches | 6.0J | 35-45 | 185/60 R15 |
| 16 inches | 6.0J | 35-45 | 195/50 R16 |
The choice of a larger diameter must be justified. If you drive your car mainly in the city, 15-inch wheels with a 60 profile are the best choice in terms of price/quality/comfort ratio.
βοΈ Check before purchasing discs
Nuts and bolts: fastening nuances
Fasteners for Nissan Note have a specific seat shape. The most commonly used nuts are spherical (radius) seat or conical seat. The wrong type of nut (eg using a flat nut instead of a ball nut) will cause the disc to sit unevenly on the hub.
The length of the bolts or nuts also matters. If you are installing long offset wheels or using spacers, the standard bolts may not be the right length. In this case, it is necessary to select extended fasteners to ensure sufficient engagement in the hub.
- π©Seat type: Sphere R12 (most often)
- π© Carving: M12x1.25
- π© Standard bolt length: 28-30 mm (for stamping)
When replacing discs, it is strongly recommended to change the set of nuts, especially if the old elements have signs of corrosion or damage to the threads. This will ensure reliable fastening and prevent the wheels from unscrewing themselves.