Nissan Note (E11/E12) bolt pattern: table of wheel and tire parameters

Selection of rims for Nissan Note - a task that requires attention to detail. An error in the bolt pattern parameters can lead to vibrations, premature wear of the suspension, or even emergency situations. In this guide we will look at all the key characteristics: PCD (fastening pitch), departure ET, center hole diameter (DIA) and compatibility with different generations of the model.

Feature Nissan Note (especially in bodies E11 And E12) - unification of many parameters with other alliance models Renault-Nissan, but there are also nuances. For example, Japanese versions may differ from European ones. We have collected current data for all modifications, including rare configurations with rear drum brakes, which require discs with a special offset.

The article will be useful for both beginners and experienced car owners. Here you will find not only hard numbers, but also practical advice: how to measure the bolt pattern yourself, which wheels are suitable from other models Nissan, and why you shouldn’t blindly trust salespeople in stores. Let's start with the main thing - a table of standard parameters.

Standard Nissan Note bolt pattern: table by generation

Bolt pattern parameters Nissan Note depend on the generation and year of manufacture. Below is a summary table for all versions, including restyled models. Please note: the data is valid for standard equipment without tuning suspension modifications.

Generation	Years of manufacture	PCD (bolt pattern)	Reach ET (mm)	DIA (mm)	Mounting thread
E11 (dorestyle)	2004–2009	4×100	35–40	60.1	M12×1.25
E11 (restyle)	2009–2013	4×100	35–42	60.1	M12×1.25
E12 (European version)	2012–2020	4×100	38–45	60.1	M12×1.25
E12 (Japanese version)	2012–2021	4×100	35–42	60.1	M12×1.25
Note e-Power (hybrid)	2016–present vr.	4×100	38–45	60.1	M12×1.25

Important: parameters for Nissan Note e-Power (hybrid version) are the same as E12, but due to the increased weight of the car, it is recommended to use wheels with a minimum offset ET 38. Installing disks with ET < 35 may cause contact with suspension components when fully loaded.

For models with rear drum brakes (more often found in basic trim levels) E11) departure is allowed until ET 45, but only when using standard tire sizes. When installing low-profile tires, the risk of disc contact with the brake mechanism increases.

What are PCD, ET and DIA: decoding parameters

Before we talk about selecting disks, let's understand the terminology. These three abbreviations are the basis for choosing the right wheels.

• 🔧 PCD (Pitch Circle Diameter) - the diameter of the circle on which the mounting holes are located. For Nissan Note it's always 4×100, that is, 4 holes on a circle with a diameter of 100 mm. An error here is unacceptable: the disk either will not fit, or the fastening will be unreliable.
• 📏 ET (Einpress Tief) — disc offset (in mm). This is the distance from the mating plane of the disk to its central axis. The shorter the reach, the wider the track. For Note it is critical to maintain the range ET 35–45, otherwise the operation of the suspension will be disrupted.
• 🎯 DIA — diameter of the central hole (stepped belt). For all generations Note this is 60.1 mm. Drives with a large DIA can be adapted using adapter rings, but this is a temporary solution.

Interesting fact: parameter PCD 4×100 unified with many models Renault (For example, Clio or Modus), but offset and DIA may vary. Therefore, "change your shoes" Note to drives from Renault It is impossible without verification.

Another nuance is the mounting thread. All generations Nissan Note use threaded bolts M12×1.25. This is standard for most Japanese cars, but when buying used wheels, check the condition of the threads: worn or deformed bolts can lead to the wheel “breaking” while driving.

How to measure bolt pattern yourself

If you are not sure about the parameters of your Nissan Note (for example, after tuning or an accident), the bolt pattern can be measured manually. You will need a caliper and a ruler.

1. PCD Measurement:
   • 📐 Measure the distance between the centers of two adjacent mounting holes (for example, 1 and 2). For 4×100 it should be straight 100 mm.
   • 🔍 Alternative method: measure the distance between the outer holes (1 and 3) and multiply by a factor of 0.707. For Note the result should be ~141.4 mm (100 × √2).
2. Departure Check (ET):
   • 📏 Place the disc face down on a flat surface.
   • 📐 Measure the height from the surface to the mating plane (A).
   • 📐 Turn the disc over and measure the height from the surface to the rim (B).
   • 🧮 Departure ET = (B – A)/2. For Note deviation of ±2 mm from standard values is permissible.

To measure DIA, simply measure the diameter of the center hole with a caliper. If the value exceeds 60.1 mm, centering rings (hubs) will be required. However, remember: rings only compensate for diameter play, but do not correct misalignment if the PCD is incorrect.

⚠️ Attention: Some "craftsmen" advise boring holes for another PCD. This is extremely dangerous! Even a minimal increase in the diameter of the holes weakens the metal of the disk and can lead to its destruction at high speed.

What happens if you install disks with the wrong PCD?

If the PCD does not match:

- The bolts will not be tightened with the correct torque (risk of self-loosening).

- The wheel will be installed misaligned, which will lead to uneven wear of the tires and wheel bearing.

- At speeds above 80 km/h, vibrations are possible that resemble an imbalance, but cannot be eliminated by balancing.

- In a critical situation (sharp maneuver or braking), the disc may move, which will lead to loss of control.

Wheel compatibility: which models are suitable for Nissan Note

Thanks to the unified PCD 4×100, rims from other cars are often suitable for Nissan Note. However, offset, DIA, and rim width need to be taken into account. Below is a list of compatible models with details:

• 🚗 Nissan Micra (K12/K13) - full compatibility with PCD and DIA, but crash on Micra often ET 30–38. For Note you will need disks with ET ≥ 35.
• 🚗 Renault Clio (II/III) - PCD matches, but DIA may be 60.5 mm. Use centering rings with a thickness of 0.2–0.3 mm.
• 🚗 Renault Modus - identical parameters, but the width of the rims is often larger (6.5J versus 5.5J for Note). Check the clearances with the suspension!
• 🚗 Dacia Sandero (I generation) - suitable, but the mounting bolts may be shorter. Use bolts ≥ 28 mm long.
• 🚗 Suzuki Swift (ZC71S) - PCD matches, but the offset is frequent ET 45–50. For Note Only disks with ET ≤ 45.

Critical point: discs from Nissan Juke (despite the same PCD) are not suitable for Note due to the larger offset (ET 30–35) and width (7J). Their installation will lead to interference with the arches and suspension arms.

When choosing drives from other models, always check:

1. Coincidence PCD 4×100.
2. Reach in range ET 35–45.
3. DIA ≤ 60.1 mm (or the ability to install hubs).
4. Disc width: for Note optimal 5.5J–6.5J.

Match PCD (4×100)✅

ET offset in the range of 35–45 mm✅

DIA ≤ 60.1 mm (or presence of hubs)✅

Disc width 5.5J–6.5J✅

No dents/cracks on the rim✅

The threads of the mounting holes are not broken✅

-->

Tire selection: what sizes does Nissan recommend?

Chatting is only half the battle. It is equally important to choose tires that are compatible with the rims and characteristics Nissan Note. The manufacturer recommends the following sizes:

Generation	Standard size	Alternative sizes	Pressure (bar)
E11 (1.4/1.6)	175/65 R15	185/60 R15, 165/70 R14	2.2 / 2.0*
E12 (1.2/1.5)	185/65 R15	195/55 R16, 175/65 R15	2.3 / 2.1*
Note e-Power	185/60 R16	195/55 R16, 175/65 R15	2.4 / 2.2*

* The first value is the front axle, the second is the rear axle.

When choosing alternative sizes, consider:

• 📉 Reducing the tire profile (for example, from 65 to 55) improves handling, but increases the risk of wheel damage on bad roads.
• 📈 Increasing the tire width (from 175 to 195) increases grip, but can lead to contact with the wheel arch liners when fully loaded.
• ⚖️ Changing the wheel diameter by more than 3% from the standard one will lead to malfunctions of the ABS and speedometer.

For Nissan Note e-Power (hybrid) it is recommended to adhere to standard sizes 185/60 R16 or 195/55 R16. Installation of low profile tires (e.g. 205/45 R17) will increase the load on the suspension and reduce the life of the shock absorbers.

⚠️ Attention: When switching to non-standard tire sizes, be sure to adjust the ABS sensors! Otherwise, the system may operate falsely when braking, especially on wet roads.

Common mistakes when choosing disks and how to avoid them

Even experienced car owners sometimes make mistakes when selecting wheels for Nissan Note. Here are the most common ones and how to prevent them:

• 🔄 Ignoring departure (ET): Installing disks with ET < 35 or ET > 45 shifts the center of gravity of the wheel, accelerating wheel bearing wear. Check the offset with a caliper or in the technical documentation.
• 🔩 Bolt thread mismatch: Bolts from Renault (For example, M12×1.5) are not suitable for Note. Always use threaded bolts M12×1.25 and length ≥ 28 mm.
• 🛞 Neglect of balancing: New disks require mandatory balancing, even if they came from the factory. An imbalance of 10–15 grams at a speed of 120 km/h will cause vibration in the steering wheel.
• ❄️ Ignoring seasonality: Tires 185/65 R15 summer and winter ones have different outer diameters! Winter tires are usually 1-2% higher, which can lead to skidding.

Another common mistake is buying discs with a “universal” PCD (for example, 4×100/114.3). Such discs have elongated holes, which allows them to be installed on different cars, but the fastening will be unreliable. For Nissan Note Only discs with clear PCD 4×100.

When purchasing used drives, pay attention to:

1. Paint/Coating Condition: Chips and corrosion may hide cracks.
2. Date of manufacture: discs older than 10 years lose strength due to metal fatigue.
3. Availability of a certificate: discs without markings or with a suspiciously low price may be counterfeit.

Tuning and non-standard solutions: what is possible and what is not

Many owners Nissan Note want to make their car stand out by installing non-standard wheels. However, not all modifications are safe. Let's look at acceptable and prohibited options.

Allowed modifications:

• 🎨 Discs with a different design, but standard parameters: You can install any disks with PCD 4×100, ET 35–45 And DIA 60.1, if they are certified.
• 🔼 Increasing rim width to 7J: Allowed provided that low profile tires are used (e.g. 205/45 R17) and checking clearances with the suspension.
• 🔽 Installing cast wheels instead of stamped ones: Reduces unsprung weight, improving handling. But alloy wheels are more fragile - avoid potholes!

Prohibited or dangerous modifications:

• ❌ Discs with PCD 4×114.3: Even with adapters, this is unsafe - the bolts will not be tightened evenly.
• ❌ Departure ET < 30 or > 50: Will cause excessive stress on wheel bearings and suspension arms.
• ❌ Discs with DIA > 66.1 mm without hubs: The wheel will be mounted off-center, which will cause wobble.
• ❌ Tires with outer diameter differing by more than 3%: The speedometer will lie and the ABS will not work correctly.

For lovers of low-profile tires: on Nissan Note wheels can be installed 195/50 R16 or 205/45 R17, but only under the following conditions:

1. Disc offset ET ≥ 40.
2. Disc width no more than 7J.
3. Checking clearances when the car is fully loaded (4 passengers + luggage).
4. Adjustment of ABS sensors in the service.

Remember: any changes to the wheels affect the behavior of the car. For example, increasing the wheel width by 1 inch (from 6J to 7J) increases the risk of hydroplaning on wet roads if the tires are not properly selected.

What happens if you put 4x114.3 wheels on a Nissan Note?

Technically, you can install PCD 4x114.3 drives on the Note using eccentric bolts or adapters, but this will lead to:

- Uneven tightening of bolts (risk of self-loosening).

- Displacement of the wheel center, which will cause vibrations at speeds > 80 km/h.

- Accelerated wear of wheel bearings (2–3 times faster).

- Problems with passing technical inspection (inconsistency of design).

In Europe and Japan, such modifications are prohibited by law.

FAQ: answers to frequently asked questions

Is it possible to install Nissan Micra wheels on the Note?

Yes, but with reservations. Discs from Nissan Micra (K12/K13) have the same PCD 4×100 And DIA 60.1, but departure on Micra often ET 30–38. For Note Only disks with ET ≥ 35. Also check the width: on Micra 6J wheels are often installed, whereas for Note optimal 5.5J–6.5J.

What bolts are needed for Nissan Note?

For all generations Nissan Note threaded bolts are used M12×1.25 and a length of at least 28 mm. For alloy wheels, it is recommended to use bolts with a tapered fit (cone angle 60°). When installing wheels with increased thickness (for example, 7J), bolts 30–32 mm long may be required.

What happens if you install wheels with an offset of ET 30?

Installing disks with ET 30 will shift the wheel outward by 10–15 mm relative to the standard position. This will lead to:

• Increased load on wheel bearings (lifetime will be reduced by 2–3 times).
• Risk of the tire hitting the fender liner when fully loaded or on uneven surfaces.
• Changes in handling: the car will become more “nervous” when cornering.
• Problems with passing technical inspection (in most countries, flight outside the approval is a reason for refusal).

What is the maximum size of disks that can be installed on Note?

Without suspension modification maximum dimensions:

• For E11: 16" with tires 195/50 R16 and departure ET 38–42.
• For E12 And e-Power: 17" with tires 205/45 R17 and departure ET 40–45.

To install disks 18" you will need:

• Replacing shock absorbers with shortened ones (for example, from Nissan Juke).
• Trimming fender liners.
• Using tires with a minimum profile (215/35 R18), which will negatively affect comfort.

Do new disks need to be balanced?

Yes, definitely! Even new discs have a minimal imbalance (1-5 grams), which at speeds of 100+ km/h turns into noticeable vibration. Balancing should be done:

• When installing new disks.
• After disk repair (editing, welding).
• Every 10–15 thousand km (or when changing tires seasonally).

For Nissan Note Dynamic balancing (on a rotating stand) is recommended rather than static balancing.