Commercial Pickup Truck Owners Nissan Atlas Often faced with the need to replace rims or tires - be it wear, tuning or seasonal tire changes. But an error in choosing bolt pattern parameters can lead to vibrations, uneven tire wear, or even accidents. This article will help you understand the key characteristics: PCD (bolt pattern), ET (departure), DIA (center hole) and hub diameter for all generations Atlas, including rare modifications.
We analyzed factory manuals, disc manufacturers' data and owner reviews to collect up-to-date information. Here you will find not only dry numbers, but also practical advice: how to measure the parameters yourself, which disks are suitable from other models Nissan, and what to do if original spare parts are not available. We will pay special attention to typical mistakes during selection - even experienced car owners avoid them.
What is a bolt pattern and why is it important for the Nissan Atlas
Bolt pattern (or PCD - Pitch Circle Diameter) is the diameter of the circle on which the centers of the wheel rim mounting holes are located. For Nissan Atlas this parameter is critical, since incorrect selection will lead to:
- 🔧 Uneven tightening of bolts — the disc will “walk” when moving, causing the steering wheel to wobble.
- 🚗 Accelerated wear of wheel bearings due to a shifted center of gravity.
- 💥 Unscrewing the wheel while driving - an extreme case, but possible with strong vibration.
On Atlas used standard for commercial pickups Nissan bolt pattern 6×139.7 (6 holes, circle diameter 139.7 mm). However, there are nuances: some modifications for the Japanese market (for example, Atlas F24 with a diesel engine) may have other parameters. Always check the compatibility chart or the original disc labeling.
⚠️ Attention: Wheels with bolt pattern 6×135 (for example, from Toyota Hilux) are visually similar, but incompatible with Atlas. A difference of 4.7 mm will lead to misalignment and the impossibility of fully tightening the bolts.
Nissan Atlas bolt pattern parameters by generation
Model Nissan Atlas was produced from 1981 to 2020 in several generations, and their technical characteristics vary. Below is a summary table with parameters for the most common versions:
| Generation/Modification | Years of manufacture | Bolt Pattern (PCD) | Reach (ET), mm | Centering hole (DIA), mm | Fastener thread |
|---|---|---|---|---|---|
| Atlas H40/H41 (gasoline/diesel) | 1981–1997 | 6×139.7 |
+15...+30 | 106.1 | M12×1.25 |
| Atlas F24 (all-wheel drive) | 1997–2004 | 6×139.7 |
+20...+35 | 106.1 | M12×1.25 |
| Atlas Onebox (van) | 2004–2020 | 5×114.3 |
+35...+45 | 66.1 | M12×1.5 |
| Atlas D22 (export versions) | 1997–2004 | 6×139.7 |
+10...+25 | 106.1 | M12×1.25 |
Please note: Atlas Onebox (van) uses bolt pattern 5×114.3, like passenger models Nissan (Teana, X-Trail). This is important to consider when purchasing used drives. Also for all-wheel drive versions (4WD) departure (ET) are usually more positive than rear-wheel drive vehicles due to the wide track.
- Steel stamped
- Cast light alloy
- Forged
- I don't know what to choose
How to measure bolt pattern yourself
If you do not have access to documentation or the markings on the disk have been erased, the parameters can be determined manually. You will need:
- 📏 Caliper or ruler with high accuracy.
- 🔨 A set of wrenches (for checking threads).
- 📐 Protractor (optional, to check the offset).
Step 1: PCD Definition
For discs with even number of holes (for example, 6 per Atlas) measure the distance between the centers of two opposite bolts - this will be the PCD value. For odd quantity (5 holes per Onebox) use the formula:
PCD = расстояние между соседними отверстиями × 1.051 (для 5 болтов)
PCD = расстояние × 1.155 (для 4 болтов)
Step 2: Departure Check (ET)
The offset is measured from the mating plane of the disk to its central axis. Positive ET means the plane is outward, negative ET is inward. For Atlas a deviation of ±5 mm from factory values is acceptable, but larger changes will require camber adjustment.
Measure the PCD and compare with the table|Check the diameter of the center hole (DIA)|Ensure that the fastener threads match|Check the offset (ET) with a tolerance of ±5 mm|Estimate the width of the rim (must match the width of the tire)-->
Compatible wheels from other Nissan models
If the original discs are for Atlas difficult to find, you can consider analogues from other models Nissan or concern Renault-Nissan. The main rule: all parameters (PCD, ET, DIA) must match. Here are the tested options:
- 🚙 Nissan Navara D22/D40 - full bolt pattern compatibility
6×139.7and departure+20...+30. - 🚙 Nissan Pathfinder R50 (until 2004) - drives with PCD are suitable
6×139.7, but DIA check is required (sometimes 110mm). - 🚙 Renault Master (van) - compatible with Atlas Onebox (PCD
5×114.3). - 🚙 Mitsubishi L200 (until 2015) - the bolt pattern is the same, but the offset may differ by 5–10 mm.
Critical nuance: discs from Nissan Patrol (even with PCD 6×139.7) often have a larger centering hole (DIA 110 mm instead of 106.1 mm). They can be adapted using adapter rings, but this will reduce the reliability of the fastening.
⚠️ Attention: Discs from Toyota Hilux (PCD 6×139.7) are visually suitable, but have a different shape for the mounting holes (60° cone instead of 45° Nissan). This will result in incomplete seating and play.
Selection of tires for Nissan Atlas: sizes and indices
The bolt pattern is only half the task. It is equally important to choose tires that match the wheel parameters and load of the pickup truck. For Atlas The following sizes are valid:
| Modification | Factory tire size | Acceptable analogues | Load index (min.) | Speed index (min.) |
|---|---|---|---|---|
| Atlas H40 (gasoline) | 205/75 R15 |
215/70 R15, 195/80 R15 |
96 (710 kg) | T (190 km/h) |
| Atlas F24 4WD | 235/75 R15 |
245/70 R16, 225/75 R16 |
104 (900 kg) | S (180 km/h) |
| Atlas Onebox | 185/70 R14 |
195/65 R15, 175/70 R14 |
92 (630 kg) | T (190 km/h) |
When choosing tires, consider:
- 🔄 Seasonality: All-season tires with markings are preferred for commercial vehicles
M+S(dirt and snow). - 🏋️ Load Index: Must be 10-20% higher than the maximum load capacity of the pickup truck (see placard on driver's door).
- 🛣️ Profile: low profile tires (e.g.
245/50 R17) are not suitable for Atlas due to the risk of damage to the discs on uneven surfaces.
When purchasing used tires for Nissan Atlas check the production date (last 4 digits of the DOT code). Tires older than 5 years lose elasticity, even if the tread is normal.
Tuning and non-standard wheels: what you need to know
Many owners Atlas seek to improve the appearance of a pickup truck with large wheels or low-profile tires. However, such changes require caution:
- ⚠️ Diameter increase: Discs
R17and more will require trimming arches or a suspension lift. Without this, the tires will touch the body when fully loaded. - ⚠️ Negative departure: Discs with ET
-10...0visually widen the track, but increase the load on the wheel bearings. - ⚠️ Wide tires: Size wider
245 mmmay require the installation of arch extensions (fenders).
Popular combinations for tuning:
- 🔥
16×7J ET+20with tires265/70 R16— optimal balance of appearance and cross-country ability. - 🔥
17×8J ET+15with tires265/65 R17- requires a 2–3 cm lift.
⚠️ Attention: After installing non-standard disks, be sure to check the wheel alignment geometry. Even a slight ET deviation of 10mm can shift the angles by 0.5°, resulting in uneven tire wear.
What happens if you ignore the camber after changing discs?
Incorrect camber angles lead to sawtooth tread wear, poor handling at high speeds and an increase in fuel consumption by 5–10%. In critical cases, the tread may come off or the tire cord may break.
Where to buy wheels and tires for Nissan Atlas
Original wheels for Atlas can be found:
- 🛒 Official dealers Nissan - guarantee of compatibility, but high price (from 15,000 ₽ for a stamped disk).
- 🛒 Specialty stores (For example, Kolesa-Darom, BlackTyres) - a wide range of analogues.
- 🛒 Used markets (Avito, Drom) - cheaper, but requires careful testing for runout and corrosion.
- 🛒 Foreign sites (eBay, Alibaba) - suitable for rare modifications, but consider shipping and possible duties.
When purchasing used drives, be sure to check:
- No cracks (especially on the spokes).
- Condition of the threads of the mounting holes (check that the bolt is screwed in).
- Runout (maximum permissible - 0.5 mm).
- Match DIA (measure with caliper).
When purchasing tires for Nissan Atlas give preference to models with a reinforced frame (marking Reinforced or XL). They can withstand the increased loads of commercial vehicles.
Frequently asked questions about the Nissan Atlas bolt pattern
Can I install wheels with a 6x135 bolt pattern on the Atlas?
No, this is unacceptable. A difference of 4.7 mm will lead to the fact that only 2-3 bolts out of 6 will be tightened correctly, and the rest will be skewed. This can cause the wheel to unscrew while driving.
What is the maximum reach you can put on the Atlas F24?
For Atlas F24 safe departure range - from +10 to +35 mm. Exceeding these values will require camber adjustment or installation of spacers (but this reduces reliability).
Will wheels from Nissan Terrano fit?
Depends on the generation. Terrano II (R20) has a bolt pattern 6×139.7, but offset and DIA may vary. Always check the parameter table.
Can I use wheel spacers?
Spacers allow you to compensate for offset discrepancies, but their thickness should not exceed 15 mm. For Atlas Spacers with a centering ring are recommended to avoid runout.
What tire pressure should be on the Atlas?
Factory recommendations:
2.2–2.4 bar— for the front wheels (without load).2.6–2.8 bar— for the rear wheels (when fully loaded).3.0 bar— for off-road driving (sand, mud).
Check the pressure on cold tires.