Removing the rear seat on a Nissan Almera Classic: instructions with photos and secrets of the masters

Rear seat in Nissan Almera Classic (also known as Nissan Sunny B10 in some markets) is not only an element of comfort for passengers, but also a barrier to hidden cavities of the body, where electrical wiring, a fuel tank or even a spare tire are often hidden. Dismantling this part may be necessary to clean the interior, repair the trim, access the fuel pump, or lay additional cables. However, many owners are faced with a problem: how to remove the seat without damaging the plastic latches or breaking the fasteners?

In this article we will analyze the process step by step - from preparing tools to final assembly. We will pay special attention typical beginner mistakes, which lead to breakage of clips or deformation of the casing. And you will also find out why on some versions Almera Classic 2005–2012 rear seat is mounted differently than on restyled 2013+ models. If you plan to work with electrics under the seat, don't skip the safety section!

Preparation: Tools and Precautions

Before you begin dismantling, make sure you have everything you need. Most operations are performed without specialized tools, but some nuances depend on the year of manufacture of the car. For example, on Almera Classic Before 2010, seat mounts may be tighter due to aging plastic.

Here is the minimum set you will need:

• 🔧 Flat head screwdriver (preferably with a thin tip for prying off the clips).
• 🔨 Plastic puller or a mediator (so as not to scratch the casing).
• 🔩 10 or 12 mm head (for fastening bolts on some modifications).
• 🧲 Magnetic holder (so as not to lose small parts in the cabin).
• 🧴 Silicone grease (if the clips come out tight).

⚠️ Attention: If your Nissan Almera Classic equipped with airbags in the rear seat (optional for some markets), disconnect the battery 10 minutes before starting work. Contacts under the seat may trigger the squib!

Also prepare your workspace:

• 🚗 Park the car on a flat surface and turn on the handbrake.
• 🧹 Remove trash and small items from the floor - they can get in the way or get lost under the seat.
• 📸 Take a photo of the location of the clips and bolts (useful for reassembly).

Rear seat design: what you need to know before disassembling

Rear seat in Nissan Almera Classic consists of two main parts:

1. Bottom (base) — attached to the body using metal hooks and plastic clips.
2. Backrest — fixed on hinges (on sedans) or removable mounts (on hatchbacks).

On most models, the seat base rests on 4–6 clips (2-3 on each side) and 2–4 metal hooks front. However, on vehicles with ISOFIX system (optional for European versions) there may be additional bolts under plastic plugs.

Modification	Base mounting type	Backrest mounting type	Features
Almera Classic 2005–2010 (sedan)	Clips + hooks	Bolted hinges	Clips often break when removed carelessly
Almera Classic 2011–2013 (restyling)	Clips + 2 bolts under the plugs	Latch hinges	Bolts can be hidden under the skin
Almera Classic 2013–2018 (for Asian markets)	Clips + ISOFIX	Removable hinges	Requires removal of plastic covers

If your car is a restyled version (after 2010), pay attention to the plastic plugs at the base of the seat - bolts may be hidden under them. On dorestyle (2005–2010) there are usually no bolts, but the clips are more fragile.

Step-by-step instructions: how to remove the lower part of the seat

We start by dismantling the base (lower part) of the seat. This process takes no more than 10–15 minutes if you act carefully.

1. Lean your back forward (if this is possible on your modification). On sedans, the backrest is usually fixed, so we skip this step.
2. Find the mounting clips. They are located on the sides of the seat, closer to the doors. On some models, the clips are hidden under the decorative fabric - carefully bend it back.
3. Pry up the clips with a screwdriver or plastic puller. Start at the back of the seat, then move to the front. Do not pull the seat up until all the clips are released!
4. Raise the seat at the rear and slide it forward to remove it from the metal hooks at the front.

If the seat “doesn’t give in,” don’t use excessive force—most likely, one of the clips is still attached. Check the fastenings with a flashlight.

⚠️ Attention: On vehicles with heated rear seats Wires run under the base. Do not pull the seat sharply - first disconnect the connector (usually located under the center part).

After removing the base you will have access to:

• 🔋 Fuel tank flap (on most modifications).
• 🔌 Fuse box (on some versions).
• 📡 GPS or GSM antenna (if installed).
• 🧹 Hidden cavities for garbage collection.

Removing the rear seat back: nuances for the sedan and hatchback

Rear seat backrest Nissan Almera Classic is removed less frequently than the base, but sometimes it is necessary - for example, to replace the sheathing or repair hinges. The process differs depending on the body type.

For sedan:

1. Open the trunk and look for the backrest mounts at the bottom (usually 2 bolts on the sides).
2. Unscrew the bolts with a 10 or 12 mm socket.
3. Gently pull the backrest towards you - it should come out of the grooves.

For hatchback:

1. Remove the plastic covers on the hinges (they are attached with clips).
2. Unscrew the hinge mounting bolts (usually 2 on each side).
3. Lift the backrest up to release it from the latches.

On hatchbacks, the backrest is often connected to folding mechanism, so before removing, check if cables or springs are in the way. If the backrest is “jammed”, do not try to pull it out - most likely, you forgot to disconnect the lock.

What to do if the backrest bolts cannot be unscrewed?

If the bolts are stuck, use a penetrating lubricant (such as WD-40) and let it sit for 10-15 minutes. Do not use impact tools - you may strip the threads in the body.

Typical problems and how to avoid them

Even with careful dismantling, the owners Nissan Almera Classic face typical difficulties. Here are the most common of them and ways to solve them:

1. Broken clips

Plastic clips become brittle over time, especially if the seat has not been removed for years. To avoid damage:

• 🔹 Before removing, warm up the clips with a hairdryer (temperature 40–50°C will make the plastic more elastic).
• 🔹 Use plastic puller only — a metal screwdriver often breaks the clips.
• 🔹 If the clip is broken, replace it with a new one (item number for Almera Classic: 77110-4M000).

2. Rusted backrest bolts

On cars older than 10 years, the backrest mounting bolts often rust. To unscrew them:

• 🔧 Use a head with an extension for better access.
• 🔥 Heat the bolt with a construction hairdryer (do not overheat - 1-2 minutes is enough).
• 🔩 If the bolt still doesn’t fit, try unscrewing it counterclockwise with light blows of the hammer on the key.

3. Damaged skin

The fabric or leatherette on the seat can be easily torn with sharp tools. To avoid this:

• 🧵 Place a soft cloth under the screwdriver when attaching the clips.
• 👕 If the casing is torn, use car seat repair kit (For example, 3M Scotch-Weld).

Cleaning and maintenance after removing the seat

When the seat is removed, you have a unique opportunity to spend deep interior cleaning and prevention of hidden elements. Here's what to do:

1. Cleaning the floor under the seat

• 🧽 Remove debris and dust with a vacuum cleaner with a narrow nozzle.
• 🧼 Wipe the plastic with a damp cloth and car shampoo (for example, Sonax Xtreme).
• 💦 To remove stains, use steam cleaner (if you have access to it).

2. Checking the electrical wiring

Under the rear seat there are wires to:

• 🔋 Fuel pump (on most modifications).
• 🔌 Airbag control unit (if equipped).
• 📡 Antenna or sound amplifier.

Check the integrity of the insulation and the reliability of the connectors. If you notice melted wires, this is a reason to check the fuses (F22 And F23 in the block under the hood are responsible for the fuel pump).

3. Lubrication of mechanisms

If the seat back squeaks or is hard to fold, lubricate:

• 🛢 Back loops (use silicone grease, so as not to stain the casing).
• 🔗 Cables for the folding mechanism (on hatchbacks).
• 🔩 Threaded mounting bolts (for easy dismantling in the future).

Reassembly: how to install the seat correctly

Installing the seat back seems simple, but there are some nuances. If the clips or bolts are not secured correctly, the seat will squeak or wobble when you move.

Procedure:

1. Check the condition of the clips. If they are deformed, replace them.
2. Install the seat base onto the metal hooks at the front, then press down on the back until the clips click into place.
3. Make sure the seat doesn't wobble. Move it from side to side - if there is play, the clips are not latched.
4. Secure the backrest (if filmed). On the sedan, tighten the bolts firmly 10–12 Nm, on a hatchback, check the operation of the folding mechanism.

After assembly, check:

• 🔌 Seat heating operation (if any).
• 🚗 No extraneous sounds when moving (creaks, knocks).
• 🔋 Tightness of the fuel tank hatch (if its cover was removed).

⚠️ Attention: If the seat sags or tilts to one side after installation, check to see if the metal hooks on the front are broken. They can be restored by welding or replaced with new ones (article: 80310-4M000).

Frequently asked questions (FAQ)

Is it possible to remove the rear seat? Nissan Almera Classic without tools?

Theoretically, yes, if the clips are not stuck. However, without a flathead screwdriver or puller, there is a high risk of breaking the plastic fasteners. For backrest bolts, a tool is required.

How many mounting clips are there on the back seat? Almera Classic 2008?

Most sedans from 2005–2010 are equipped with 4 clips (2 on each side) and 2 metal hooks front. On restyled models there may be 6 clips + 2 bolts under the plugs.

What should I do if the fuel pump stops working after removing the seat?

Most likely, you touched the pump connector or fuse. Check:

• 🔌 Connector connection under the seat (white or black block with 3-4 wires).
• 🔥 Fuse F22 (15A) in the block under the hood.
• 🛢 Wiring integrity (often rubs against the body).

If the pump does not hum when you turn on the ignition, there is an electrical problem.

How to remove the trim from the rear seat for reupholstery?

The casing is attached to:

• 🧵 Staples (you need a furniture staple remover).
• 🔹 Plastic pistons (pry off with a screwdriver).
• 🧶 Glue (on some versions with leather trim).

Start with the sides of the seat, then release the front and back edges. For careful removal, use plastic spatula.

Is it possible to drive without a back seat?

Technically yes, but:

• ⚠️ This is violates traffic rules (lack of standard equipment).
• 🚨 In case of an accident, loose objects in the cabin will become dangerous projectiles.
• 📄 Questions may arise during maintenance.

If the seat is removed temporarily, secure it with straps in the trunk.