Nissan Almera G15 is one of the most popular sedans in the budget segment, but even in basic trim levels the manufacturer often skimps on such important elements as fog lights. Their absence not only impairs visibility in difficult weather conditions, but also reduces overall safety on the road. In this article we will look at how to choose the right PTF for Almera G15, which models are compatible with car electrics, how to install them yourself and avoid common mistakes when connecting.

The peculiarity of this model is the non-standard shape of the bumper and limited space for installing additional equipment. Therefore, before purchasing, it is important to consider not only the design and brightness of the headlights, but also their overall dimensions, mounting type and compatibility with the on-board computer. We analyzed owner reviews, technical specifications and market offers to create the most complete guide possible.

Original fog lights for Nissan Almera G15: articles and features

Factory fog lights for Almera G15 (2013–2018) are supplied complete with Comfort+ And Tekna, but they can be purchased separately. Original parts are produced by the company Stanley Electric (Japan) and have the following articles:

  • 🔦 Left headlight: 26550-4M000 or 26550-4M00A (depending on year of manufacture)
  • 🔦 Right headlight: 26560-4M000 or 26560-4M00A
  • 💡 Lamp: H11 (power 55 W, base PGJ19-2)
  • 🔌 Wiring and relay: kit 26510-4M000 (includes control button)

The original headlights have aspherical optics with a clear cut-off line, which meets European standards ECE R19. Their key advantage is a perfect fit into the standard bumper holes without modifications. However, the price of the original can reach 8–12 thousand rubles per pair, which forces many owners to consider analogues.

⚠️ Attention: When purchasing used original headlights, check the integrity reflector — even small scratches reduce the luminous flux by 30–40%. Also check the version of the article: headlights for restyled Almera G15 (2016+) have a different connection connector.

Analogues of the original PTF: what to choose for Almera G15?

If your budget is limited, you can consider high-quality analogues from trusted brands. The main thing is that they correspond original dimensions (180×120×90 mm) and had a certificate ECE R19. The table below compares popular models:

Brand Article Lamp type Luminous flux (lm) Price (per pair), ₽ Features
Depo 335-1122L/R H11 1200 3 500–4 200 Complete analogue of the original, but with a plastic (not glass) diffuser
TYC 20-6506-00-1 H11 1300 4 800–5 500 Improved sealing, suitable for use in high humidity environments
Hella 8GA 008 141-121 H11 1400 6 200–7 000 Premium quality, aluminum body, service life up to 10 years
Bosch 1 987 302 035 H11 1350 5 800–6 500 Universal model, requires modification of fastenings

When choosing analogues, pay attention to diffuser material: glass is more durable than plastic, but heavier and more expensive. Also check the package contents - some manufacturers do not include sealing rubber gasketsthat protect against moisture.

📊 Which fog lights do you prefer for Almera G15?
  • Original Nissan
  • Analogs Depo/TYC
  • Premium brands (Hella, Bosch)
  • Universal (with modification)
  • I haven't decided yet

Connection diagram for fog lights: step-by-step instructions

Connecting PTF to Almera G15 requires intervention in the standard electrical system, so it is important to follow the diagram and observe polarity. Below is a standard diagram for models without factory preparation (i.e. when there are no connectors and wiring in the bumper):

The following materials will be required:

  • 🔌 4-pin relay (for example, Bosch 0 332 019 150)
  • 🔌 15 A fuse
  • 🔌 Wire with a cross section of 1.5–2 mm² (length ~3 m)
  • 🔌 Female/male terminals and heat shrink tubes
  • 🔧 Control button (you can use the standard one) Nissan Note, article 25560-4M000)

Connection sequence:

  1. Remove the negative terminal from the battery.
  2. Lay the wire from fuse box (use a free slot or a branch from the dimensions) to the relay installation location (for example, behind the glove compartment).
  3. Install the relay and fuse in the positive wire.
  4. Connect the relay control wire to the button (pin 85) and to +12V from the ignition switch (pin 86).
  5. Connect the ground (minus) to the car body.
  6. Connect the headlights to the relay output (pin 87).

Connection polarity (plus to plus, minus to minus)|

Insulation of all connections with heat shrink |

Reliability of fastening headlights to the bumper|

No kinks in wires|

Power button functionality-->

For models with factory training (there are connectors in the bumper, but no headlights) the circuit is simplified: just connect the headlights to the existing connectors and install a button in the cabin. In this case, the relay and fuse are already integrated into the control unit.

⚠️ Attention: Do not connect the PTF directly to the battery without a relay! This will lead to circuit overload and may cause a fire. Also avoid twisting - use only solder or crimp terminals.

Installing fog lights: step-by-step process with photos

Installation of PTF on Almera G15 Requires removal of the front bumper. For this you will need:

  • 🔧 10 mm socket wrench
  • 🔧 Phillips and flat head screwdriver
  • 🔧 Plastic clips (item no. 90467-04M00, ~10 pcs.)
  • 🔧 Silicone sealant (for example, ABRO)

Algorithm of actions:

  1. Remove the front wheel and fender liner from the desired side (to access the bumper bolts).
  2. Unscrew the 2 bolts securing the bumper to the fender and the 3 bolts from the bottom.
  3. Disconnect the clips holding the bumper along the perimeter (be careful, they are fragile!).
  4. Remove the bumper by disconnecting the parking sensor connectors (if equipped).
  5. Cut technological holes for the headlights (according to the template included in the kit).
  6. Install the headlights, securing them with M6 bolts with nuts and rubber gaskets.
  7. Apply sealant along the contour of the junction of the headlight and bumper.
  8. Reassemble everything in reverse order.

When installing universal headlights (not the original shape), it may be necessary to modify the bumper - for example, widening the holes or strengthening the fasteners with metal plates. Also note that universal models often require tilt angle adjustment after installation.

How to remove the bumper without damage?

1. Preheat the clips with a hairdryer (temperature 50–60°C) - this will make the plastic more elastic.

2. Use a special clip remover (for example, Lisle 58100) so as not to break them.

3. Start detaching the bumper from the corners where the fastenings are less rigid.

4. If the clip is broken, do not try to insert it back - replace it with a new one (cost ~50 ₽/piece).

Adjusting fog lights: why is it important and how to do it right

Unregulated PTFs not only blind oncoming drivers, but also do not perform their main function — illumination of the road in front of the car. According to GOST R 51709-2001, the light beam of the fog lights should:

  • 📏 Have a clear upper limit (no higher than 20 cm from the headlight level at a distance of 10 m).
  • 📏 Spread at least 40° wide.
  • 📏 Light up the roadside at a distance of up to 25 m.

To adjust you will need:

  • 📏 Tape measure or ruler
  • 📏 Screwdriver (for turning the adjusting screws)
  • 📏 Vertical wall or straight fence
  • 📏 Level (to check the level of the car)

Procedure:

  1. Place the car on a level area at a distance of 5 meters from the wall.
  2. Mark the wall with chalk or tape:
    • Vertical lines down the center of each headlight.
    • The horizontal line is 10 cm below the PTF installation height.
  • Turn on the fog lights and adjust the screws on the headlight so that the upper edge of the light spot coincides with the horizontal line.
  • Check the symmetry of the light beams.
    • 💡

    If after adjustment the light still blinds oncoming drivers, set blackout film (For example, LightTape) onto the top of the diffuser. This will reduce the light intensity by 30–40% without losing the illumination of the road.

    Typical mistakes when installing PTF on Almera G15 and how to avoid them

    Even experienced car owners make mistakes that lead to short circuit, blown fuses or incorrect operation of headlights. Here are the most common of them:

    1. Use of high power lamps (over 55 W).

      This leads to melting of the connectors and overheating of the wiring. Maximum permissible power for Almera G15 — 60 W, but only if an additional relay and a 20 A fuse are installed.

    2. Incorrect polarity when connecting.

      If you confuse plus and minus, the headlights may work unstable or not turn on at all. Always check polarity with a multimeter before final assembly.

    3. Lack of sealing of holes.

      Moisture entering through loose joints leads to corrosion of the contacts and failure of the headlights. Use silicone sealant and check the seals.

    4. Connection without relay.

      Direct connection to a button or dimensions will place a load on the circuit and may cause a fire. Relay is a must!

    5. Ignoring adjustments.

      Unadjusted headlights blind oncoming traffic and do not illuminate the road. This is fraught with a fine under Art. 12.5 Code of Administrative Offenses (500 ₽).

    💡

    The most dangerous mistake is connecting the PTF to the size circuit without a relay. This overloads the fuse box and can damage the on-board computer.

    Maintenance and care of fog lights

    To make PTFs last longer, just follow a few simple rules:

    • 💧 Wash your headlights soft sponge with car shampoo (for example, Karcher). Do not use abrasives as they will scratch the lens.
    • 🔧 Check once a year headlight mounts - Vibration can loosen bolts.
    • 💡 Change lamps in pairs, even if one burned out. Different light intensities impair visibility.
    • 🛠️ Treat before winter contacts special lubricant (for example, Liqui Moly Kontakt-Spray) to protect against oxidation.

    If the headlights started fade or a yellowish tint appears, this is a sign of aging of the diffuser. In this case, polishing (for example, with paste) will help 3M 39045) or glass replacement. To restore the transparency of plastic diffusers, use UV protective coating (For example, Meguiar’s PlastX).

    The average service life of high-quality PTFs is 5–7 years. If the headlights started fog up from the inside, this means depressurization. In this case, only replacing the seal or the entire headlight will help.

    FAQ: Frequently asked questions about fog lights on Nissan Almera G15

    Is it possible to install LED lamps in standard PTFs?

    Technically yes, but there are some nuances:

    • 🔦 LEDs must have built-in driver to stabilize the current.
    • 🔦 Power should not exceed 30 W (equivalent to 55 W halogen).
    • 🔦 Required light beam corrector, since LEDs have a different focus.

    Best options for Almera G15:

    • Philips X-tremeUltinon LED H11
    • Osram LEDriving FOG H11

    However, please note that according to traffic regulations, the use of LEDs in headlights that are not intended for them may result in a fine.

    How can I check if my Almera G15 has factory wiring for PTF?

    Open the hood and inspect the area behind the bumper:

    • 🔌 If there is power connectors (usually black or gray) - wiring provided.
    • 🔌 Check the fuse box: if there is a free slot with the inscription FOG - there is preparation.

    You can also look under the steering column: if there is an unused connector for the button, this is a sign of factory readiness.

    What should I do if the PTFs do not light up after installation?

    Causes and solutions:

    1. Fuse is faulty — check and replace (slot F16, 15 A).
    2. Poor ground contact — clean the place where the wire is attached to the body.
    3. Polarity reversed — Swap the plus and minus on the headlight connector.
    4. Relay does not work - check it with a multimeter or replace it with a known good one.
    5. Broken wire - test the circuit with a tester.

    If the problem persists, check voltage at headlight contacts with the ignition on, it should be 12–14 V.

    Is it possible to drive with the PTF on during the day?

    According to clause 19.4 of the Russian Traffic Regulations, fog lights can be used:

    • 🌫️ In conditions insufficient visibility (fog, rain, snowfall).
    • 🚗 Instead low beam in the daytime (but only in conjunction with the dimensions).

    However, constant use of PTF during the day not recommended, as this shortens the life of the lamps and may dazzle oncoming drivers.

    Which PTFs are better - round or rectangular?

    For Almera G15 optimal rectangular headlights, because:

    • 🔹 They fit better into the bumper shape.
    • 🔹 They provide a wider beam of light, illuminating the side of the road.
    • 🔹 Easier to install (does not require modification of fasteners).

    Round headlights (eg from Nissan Juke) can be installed, but they:

    • 🔸 Requires cutting out non-standard holes in the bumper.
    • 🔸 Often have the worst cut-off line.