Introduction to the world of search with Safari
Finding metal objects underground requires not only patience, but also a deep understanding of how your equipment works. Metal detector Safari is a popular model often found among novice and intermediate researchers due to its simplicity and reliability. To get the most out of it, it's not enough to just turn on the device and start walking; it is necessary to understand the intricacies of its calibration and response to different types of targets.
This article will help you master Safari from scratch, revealing customization secrets that are often overlooked in standard brochures. You'll learn how to distinguish valuable metal from junk, how to avoid false positives, and how to properly care for your search head. Correct operation of the device directly affects the detection depth and comfort of work in the field.
Initial device setup and calibration
Before each search, it is necessary to carry out an initialization procedure so that the device adapts to the current environmental conditions. First turn on the power while holding the button Power, and wait a few seconds until the Ready light turns on. It's important to make sure that earth balance installed correctly, otherwise the device will react to soil mineralization, producing false signals instead of target ones.
For quick setup, the automatic calibration mode is often used, which is activated by pressing the corresponding button. At this moment you need to keep search coil at a height of 15-20 centimeters above the ground, without touching grass or stones. If the soil is highly mineralized, manual sensitivity adjustments may be necessary to balance out background noise.
Do not forget to check the battery charge, as low voltage can lead to unstable operation of the electronics and a decrease in search depth. Pay close attention to the charge indicator on the display; when it blinks, it is better to replace the battery with a fresh one so as not to interrupt the search process at a critical moment.
⚠️ Warning: Never turn on the device with the coil lying on the ground or in tall grass, as this will cause an immediate false alarm and reset the calibration.
After switching on and setting up, it is recommended to conduct a test run with a known object, for example, a coin, to ensure that the system is working. If the signal is reproduced clearly and without delays, you can proceed to real search actions. This is a simple step that will save you hours of wasted digging in the future.
Discrimination modes and target identification
One of the key functions Safari metal detector is the ability to filter out unwanted metals. The device usually offers several discrimination modes that allow you to ignore iron or, conversely, highlight non-ferrous metals. Understanding how it works discrimination, will help you avoid unnecessary holes from rusty nails and bottle caps.
In mode All Metal (All metals) the device responds to any conductive medium, which is useful for searching for large objects or in highly mineralized conditions where discrimination fails. However, for point search it is better to use the discrimination mode, turning off the reaction to low indices characteristic of steel. Adjusting the discrimination thresholds allows you to configure the device so that it is silent when passing over debris.
Gold rings may have the same index as iron nails if they are heavily oxidized or have a specific shape. Therefore, relying only on the sound signal and not looking at the display when making a decision to dig is a serious mistake for a beginner.
- 🔍 Use the discrimination mode to save time on cleaning the area from small debris.
- 🔍 In “Iron” mode, the device will emit an intermittent signal, helping to immediately weed out unnecessary targets.
- 🔍 To search for coins and jewelry, switch to the "Con" (Capacitor) mode or similar non-ferrous metal profile.
Interpreting sound takes practice: a low and dull tone usually indicates ferrous metal, while a high and clear tone usually indicates non-ferrous alloys. Different manufacturers have their own audio encoding algorithms, so take the time to study the audio profile of your specific one. Safari at the training ground.
⚠️ Warning: Do not ignore targets with a low discrimination index if you are looking for antique coins or artifacts, as they may have low conductivity due to corrosion.
- All metals
- Non-ferrous metals
- Hardware disabled
- I configure it manually for each section
Scanning technique and depth search
The effectiveness of the search depends not only on the device settings, but also on your scanning technique. The movements of the reel should be smooth and rhythmic, with a slight overlap of the previous trajectory. If you swing the reel too fast, detection depth will drop sharply, and you risk missing a small target under your feet.
Height above the ground is a critical parameter: try to keep the coil at a distance of 2-5 cm from the surface, without touching the grass. When driving on uneven terrain, it is necessary to smoothly raise and lower instrument handle, maintaining a constant gap. Violation of this rule will result in signal loss at the target peak or false positives.
The speed of passage also plays a role: for small targets (coins, rings), the speed must be minimal so that the electronic processor has time to process the signal. To search for large objects (pipes, treasures), you can increase the pace, but the risk of missing small things increases many times over.
- 🏃♂️ Move the coil from side to side with an amplitude of about half a meter.
- 🏃♂️ Keep the coil parallel to the ground, tilting it only when scanning a shaft or ditch.
- 🏃♂️ Check each target from different angles to confirm its shape and composition.
If you find a signal, don't rush to dig right away. Move the coil towards the center of the target from different directions to accurately determine the passing point. Often the signal sounds loudest not directly above the object, but slightly to the side due to the shape of the coil's magnetic field.
☑️ Scanning technique
Dealing with interference and difficult conditions
Electronic interference is the main enemy of any metal detector. Power lines, cell towers, and even other operating devices can create strong interference, making a search impossible. If you hear a constant hum or the device starts to go crazy for no apparent reason, check if you are within range electromagnetic interference.
In such situations, try changing the coil orientation or changing the operating frequency if your model Safari supports this feature. Sometimes it is enough to simply move a few tens of meters away from the source of interference. If the noise persists, try reducing the sensitivity of the device, although this will reduce the search depth.
Mineralized soil (salt water, black forest soil) also creates difficulties. Under such conditions, automatic ground balance may not work correctly, requiring constant manual adjustment. Use the mode Manual Ground Balanceto manually adjust the device for a specific area, excluding reaction to the ground.
| Interference type | Cause | Solution |
|---|---|---|
| Constant hum | Power line or radio tower | Change of location or decrease in sensitivity |
| False positives | Soil mineralization | Manual ground balance calibration |
| Intermittent signal | Proximity of another device | Changing frequency or distance |
| Signal loss | Heavy coil moisture | Drying and checking contacts |
Humidity also affects the performance of the device: water getting into the connectors or on the board can cause short circuits or instability. After working in the rain, be sure to dry it search coil and electronic components.
⚠️ Warning: If the device begins to behave unpredictably in the field, stop searching immediately and check for external sources of interference before digging.
Sometimes the problem lies in poor contact between the reel and the rod. Inspect the connectors for oxidation and, if necessary, clean them with alcohol or a special lubricant. A reliable connection guarantees stable signal transmission from the coil to the control unit.
How to distinguish a pickup from a target? If the signal sounds constantly and does not depend on the movement of the coil, this is a pickup. If the signal appears only when the coil is pointed at a point, this is the target.-->
Device care and storage
Durability Safari metal detector directly depends on the quality of care. After each use in a dirty or wet area, wipe the reel and rod with a dry cloth. Dirt and moisture can corrode the protective coating and cause corrosion of metal parts.
Pay special attention to connectors
they must be dry and clean. If you work in the rain, use sealed covers or electrical tape to protect the contacts. Store the device in a dry place, preferably in a case, to avoid dust and direct sunlight, which can deform the plastic.
Batteries require special care: if you do not plan to use the device for a long time, be sure to remove the batteries. This will prevent electrolyte leakage, which could permanently damage the battery compartment and the device board itself.
- 🧼 Clean the reel regularly from dirt and vegetation.
- 🔋 Store the device with the batteries removed during long periods of inactivity.
- 🛡️ Use a protective case for the rod when transporting.
Periodically check that screws and connections are secure. Vibration while walking can cause small parts to loosen over time, leading to looseness and even breakage. Simple prevention will save you money on repairs.
Regular cleaning of contacts and proper battery storage are the key to a long life of your metal detector without breakdowns.
Frequently asked questions and answers
Many users face similar questions when using it for the first time Safari. Below are the answers to the most common ones, which will help you avoid common mistakes and master the device faster.
Why does a metal detector constantly beep without a target?
This may be caused by soil mineralization or electromagnetic interference. Try manually calibrating the ground balance or move away from noise sources (power lines, towers). Also check that the coil is not touching the grass or ground when turning it on.
How to increase search depth?
To increase depth, use a larger search coil (if your model supports replacement), lower the sensitivity to a level where false positives disappear, and scan more slowly. It is also important to correctly adjust the balance of the land for a specific site.
Can Safari be used in the rain?
Most models Safari The coils and rods are waterproof, but the electronics are often not protected from direct water. Use a rain cover or cover for the control box to avoid short circuits. After use, be sure to dry the device.
What to do if the device stops responding to the target?
Check the battery charge, make sure that the coil connector is inserted all the way and is not oxidized. Try resetting or recalibrating. If the problem persists, the electronics may need to be repaired or the coil needs to be replaced.
How to distinguish gold from non-ferrous metal?
Gold often has an average discrimination index similar to brass or copper. On mineralized soils it may sound like iron. The only reliable way is to dig up the target and inspect it. Gold is not magnetic and has a characteristic color and weight.
Development Safari metal detector is a process that requires practice and attention to detail. By following these instructions, you will be able to effectively use all the capabilities of the device and find interesting targets, avoiding typical beginner mistakes. Good luck in your search!