Lamps in Nissan Juke: a complete guide to selection and replacement (J10/J11)

Owners Nissan Juke The first (J10, 2010–2019) and second (J11, from 2019) generations sooner or later have to deal with replacing lamps - be it a burnt-out headlight, dim low beam or a broken brake light. It would seem, what could be simpler? But in practice, the choice of lamps for Juke conceals a lot of nuances: from differences in bases for restyled versions to strict requirements for luminous flux to pass technical inspection.

This article is not just a list of items. Here you will find analysis of all types of lamps (from dimensions to fog lights), step-by-step replacement instructions taking into account design features Juke, and also recommendations for selection between halogen, LED and xenon. We analyzed owner reviews, technical manuals and light test results to create the most practical guide possible. Particular attention was paid to typical errors due to which new lamps burn only half-heartedly or quickly burn out.

Types of lamps in Nissan Juke: sockets and purpose

Optics design Nissan Juke depends on the year of manufacture and configuration. For example, in pre-restyling versions (2010–2014) for low and high beams they used separate lamps (H7 and H1, respectively), while after 2014 the manufacturer switched to bi-xenon blocks (base D1S) in top trim levels. Below is the complete compatibility table.

Lamp type	Base	Power, W	Application	Features
Low beam	H7 (halogen) D1S (xenon)	55 35	J10 (all versions) J11 (basic configurations)	Xenon versions require an ignition unit
High beam	H1 (halogen)	55	J10/J11	In bi-xenon headlights, the high beam is implemented as a curtain
Fog lights (PTF)	H11	55	J10/J11 (optional)	In J11 from 2020 - LED optics
Side lights	W5W (T10)	5	Front/rear	Often burn out due to vibrations
Brake/tail lights	P21/5W	21/5	J10/J11	Double-filament lamp (stop + clearance)

⚠️ Attention: B Nissan Juke J11 (from 2019) installed from the factory LED headlights in top trim levels (N-Connecta, Tekna). Replacing LED modules with halogen or xenon ones will cause an error on the instrument panel and may void the warranty. For such versions, we recommend contacting official dealers.

It is also worth considering that in the European and Japanese versions Juke There may be differences in the rear light bases. For example, in some examples a lamp is used for the turn signal PY21W (yellow), not standard WY5W.

How to choose lamps for Nissan Juke: halogen vs LED vs xenon

The choice of lamp type depends on three key factors: legal admissibility, lighting characteristics And budget. Let's look at the pros and cons of each option using low beam (the most critical element) as an example.

• 🔦 Halogen lamps (H7/H11): They are legal, cheap (from 300 rubles), but last 300–500 hours. The optimal choice for technical inspection. Top Brands: Osram Night Breaker, Philips VisionPlus.
• ⚡ Xenon lamps (D1S/D2S): Brightness is 2-3 times higher than halogen, service life up to 2000 hours. However, they require the installation of ignition units and prohibited in halogen headlights (fine 500 rubles under Article 12.5 of the Administrative Code). Suitable only for standard xenon optics.
• 💡 LED lamps (H7/H11): Energy efficient, lasts up to 30,000 hours, but not all models are certified for road use. Risk of blinding oncoming drivers if installed incorrectly. We recommend: Philips Ultinon, Osram LEDriving.

🔍 Important nuance: If you decide to switch from halogen to LED, be sure to check direction of light beam. In 70% of cases, cheap LED lamps (for example, Chinese no-name) produce diffused light that blinds oncoming traffic. For Juke it is critical to choose models with correct placement of diodes relative to the headlight reflector.

Step-by-step replacement of lamps in Nissan Juke (with photos and diagrams)

The process of replacing lamps Juke differs depending on the zone: the headlights require removal of the bumper or fender liner, while the rear lights are accessible from the trunk. Below are instructions for the most popular operations.

1. Replacing the low beam lamp (H7)

🔧 Tools: gloves (to avoid touching the bulb), T20 screwdriver, flashlight.

1. Open the hood and remove protective cover headlights (turn counterclockwise).
2. Disconnect the power supply from the lamp by pressing the latch.
3. Rotate the metal lamp holder to the left and remove it.
4. Install a new lamp H7without touching the flask (grease marks will shorten the service life).

⚠️ Attention: B Nissan Juke J11 (2019+) to access the low beam lamp you must remove air filter or part of the fender liner. Without this, it is impossible to reach the headlight!

2. Replacing the bulb in the fog light (H11)

Fog lights in Juke located low, so replacement is performed from below:

1. Jack up the car or drive it onto an overpass.
2. Remove protective shield under the bumper (4 clips).
3. Turn the lamp socket counterclockwise and remove it.
4. Disconnect the connector and install a new lamp H11.

💡 Advice: If the PTF burns out frequently, check housing tightness — moisture ingress reduces the service life of lamps by 2–3 times. B Juke the first generation is a weak point due to poor ventilation of the optics.

3. Replacing brake lights (P21/5W)

The simplest procedure is access from the trunk:

1. Remove the trunk trim from the canopy side (snap off the clips).
2. Rotate the chuck counterclockwise and pull it out.
3. Click on the lamp and turn leftto extract.

⚠️ Attention: B Nissan Juke J11 (from 2020) taillights often come complete with LED modules. Replacing individual lamps in them is impossible - you need to purchase the entire unit (from 8,000 rubles).

Top 5 mistakes when replacing lamps in Nissan Juke

Even experienced car owners make mistakes that lead to rapid lamp burnout or damage to the optics. Here are the most common:

• 🧤 Touching the bulb of a halogen lamp with bare hands. Fatty traces lead to local overheating and reduce service life by 40%. Always use gloves or a cloth.
• 🔌 Incorrect connection of LED lamps. Many whales from AliExpress come with CAN bus trickswhich may cause an error Check Bulb on the panel. For Juke Only lamps with a built-in driver are suitable (for example, Philips X-tremeUltinon).
• 💧 Ignoring condensation in the headlight. If, after replacing the lamp, moisture appears inside the optics, you must dry the headlights (for example, a hairdryer) and check breather (ventilation valve).
• 🔧 Using excessive force during installation. Plastic cartridges in Juke fragile - when pressed hard they break. This is especially true for rear lights.
• 🔦 Selecting lamps with the wrong color temperature. Optimal for halogen 3200–4300K, for LED - 4000–5000K. Lamps with 6000K+ blind oncoming people and poorly illuminate the road in the rain.

What to do if the lamp burns out after a week?

The reason most often lies in voltage surges in the on-board network. Check the generator and voltage regulator relay (optimal value is 13.8–14.4V). An oxidized contact in the cartridge may also be the culprit - clean it with alcohol or WD-40.

The best lamps for Nissan Juke: 2026 ranking

Based on tests ADAC (Germany) and owner reviews Juke on the forums Drive2 And NissanClub, we have compiled a rating of lamps for key positions:

Lamp type	Model	Price, rub.	Pros	Cons
Low beam (H7)	Osram Night Breaker Laser	1 200	+30% brightness, long service life	High price
Fog lights (H11)	Philips X-tremeVision Pro150	1 500	White light (4200K), good visibility in fog	Can cause blinding if not adjusted correctly
LED low beam (H7)	Osram LEDriving HL	4 500	Legal (ECE certified), service life 10+ years	Requires precise headlight adjustments
Dimensions (W5W)	Narva Range Power White	150	Bright white light, low price	fragile flask

🔍 Expert advice: If you choose LED lamps for Juke, pay attention to models with passive cooling (radiator instead of fan). Fans often fail due to vibrations and dust, especially in off-road conditions.

Adjusting headlights after replacing bulbs

Replacing lamps is only half the battle. Out of adjustment headlights blind oncoming drivers and impair visibility. B Nissan Juke Adjustment is done using two screws on the back of the headlight:

• 🔧 Vertical adjustment: screw at the top of the headlight (marked with an arrow) ↑↓).
• 🔄 Horizontal adjustment: screw on the side (marked ←→).

📏 Adjustment algorithm:

1. Place the car on a flat area 5 meters from the wall.
2. Place marks on the wall at the center of each headlight (height is at the center of the lamp).
3. Turn on the low beam and adjust the beam so that upper limit was 5 cm below the mark.

⚠️ Attention: B Nissan Juke J11 with LED optics the adjustment is carried out only in service using a diagnostic scanner (for example, Consult-III Plus). Self-configuration may lead to system errors.

Frequently asked questions about bulbs in Nissan Juke

Is it possible to install xenon in halogen headlights on a Nissan Juke?

No, it's prohibited Traffic regulations (clause 3.6 "List of faults"). Xenon lamps have a different focus and blind oncoming drivers in halogen optics. Fine - 500 rubles. (Article 12.5 of the Administrative Code).

Why do the LED lights in the Juke blink after installation?

Reason - conflict with CAN bus. Solutions:

• Install resistance trompe l'oeil (50 ohms).
• Buy lamps with built-in CAN filter (For example, Morimoto XB).
• Disable lamp monitoring via diagnostics (not recommended).

What kind of lamps are in the PTF of Juke J11 (2020)?

B Juke J11 from 2020 on fog lights LED modules (irreplaceable separately). If it burns out, the entire unit must be replaced (article: 26530-JM01A, price ~12,000 rub.).

How to remove a headlight on a Nissan Juke to replace the bulb?

Procedure:

1. Remove the bumper (6 T20 bolts + clips).
2. Unscrew the 3 headlight mounting bolts (one on top, two on bottom).
3. Disconnect the connectors and remove the headlight.

⚠️ Attention: B Juke J11 Before removing the headlight, you must disconnect the battery - otherwise a system error will occur IPDM (lighting control unit).

What kind of bulbs are in the Juke turn signals?

In the front turn signals - WY5W (yellow), in the rear - PY21W (orange). For tuning, you can use baseless LED modules (for example, Hella LEDayFlex), but they require modification of the cartridge.