Nissan Teana J31 — a car that combines the comfort of a business sedan and the reliability of Japanese engineering. But even the most well-thought-out optics require attention: burnt-out lamps not only impair visibility, but can also result in a fine. In this article we will analyze all types of light bulbs in Teana J31 (2003–2008), their articles, analogues and replacement nuances - from dimensions to fog lights.

Feature of the model - different configurations (with halogen or xenon in the headlights), so before purchasing lamps it is important to know exactly what optics are installed on your car. We collected data on original Nissan part numbers, proven analogues and typical replacement errors, which can lead to overheating of the headlight or failure of fuses.

Types of lamps in Nissan Teana J31: what is where

B Teana J31 used until 12 different lamps — from low beam to glove compartment lighting. Their types depend on the year of manufacture and configuration. Below is a complete breakdown by zone:

  • 🔦 Low/high beam: H7 (halogen) or D2S (xenon) - depends on the version.
  • 💡 Side lights: W5W (before) / T10 (back).
  • 🚨 Fog lights: H11 (front) / P21W (rear).
  • 🔴 Stop lights/turn signals: P21/5W (two-pin).
  • 🔄 Turn signal: WY5W (yellow).
  • 📛 Number plate illumination: C5W or T10.

Important: in cars with xenon headlights (optional Premium Package) low beam is implemented through D2S, and the distant one - through a separate halogen lamp H7. You can check the type of optics by the markings on the headlight: xenon ones have a lens and an inscription D2S on the body.

📊 Which lamps do you most often change in Teana J31?
  • Low/high beam
  • Dimensions
  • Fog lights
  • Brake lights
  • Other

Original lamps and their analogues: what to choose

Factory lamps from Nissan have article numbers starting with 265xx-xxxxx, but their prices are often overpriced. There are proven analogues on the market from Philips, Osram And Narva, which are not inferior in quality. Below is a table of correspondences:

Lamp type Original Nissan part number Recommended analogue Price, ₽ (2026)
H7 (near/far) 26510-3M000 Philips X-tremeVision +130% (12972XV2) 1 200–1 500
D2S (xenon) 26510-3M010 Osram Xenarc Cool Blue Intense (66240CBI) 3 500–4 200
H11 (fog lights) 26520-3M000 Narva Range Power +110% (48368) 800–1 000
W5W (dimensions) 26530-3M000 Philips WhiteVision (12860WV2) 300–400

⚠️ Attention: When replacing D2S (xenon) avoid cheap Chinese analogues - they often have incorrect color temperature (over 6000K), which blinds oncoming drivers and can cause deprivation of rights under Art. 12.5 Code of Administrative Offences.

For halogen lamps H7 And H11 optimal choice - series Philips RacingVision or Osram Night Breaker, which give on 20–30% more light without damaging the resource. And here are the lamps marked "+300%" (for example, from MTF Light) often overheat the reflector and shorten the life of the headlamp.

Step-by-step instructions: how to replace a low beam lamp

Replacement H7 or D2S in Teana J31 does not require special tools, but there are some nuances. Let's look at the process using the halogen version as an example:

  1. Preparation: Stop the engine, open the hood and remove the negative terminal from the battery (to avoid short circuit).
  2. Access to headlight: Remove the plastic headlight cover by turning it counterclockwise. In xenon versions, you will additionally need to disconnect the ignition unit.
  3. Removing the lamp: press the plinth lock H7 and pull it towards you. For D2S First disconnect the power connector, then unscrew the lamp counterclockwise.
  4. Installing a new lamp: insert the lamp without touching the flask (fat traces reduce service life). For H7 snap the latch to D2S - screw until you hear a click.

Disconnected the battery|

Checked the lamp type (H7 or D2S)|

Prepared new gloves (for H7/D2S)|

I made sure that there was no moisture in the headlamp -->

⚠️ Attention: After replacement D2S may be required headlight adjustment (adjustment is carried out with screws on the headlight housing). If the light "shoots up", it not only blinds oncoming drivers, but also reduces the life of the lamp due to overheating.

To check for correct installation, turn on the low beam and inspect the headlight for:

  • 🔍 Even light spot (no dark streaks or blurriness).
  • 💧 Condensate — if it appears, check the tightness of the headlight cover.
  • ⚡ Flicker - a sign of poor contact or malfunction of the ignition unit (for xenon).

Fog lights: choice of lamps and replacement nuances

B Teana J31 fog lights (H11) are located in the bumper and often suffer from moisture. When replacing lamps, pay attention to:

  • 🌡️ Color temperature: optimal 3000–4300K (yellow or white neutral light). Lamps with 6000K and above are prohibited by traffic rules.
  • 🔋 Power: do not exceed 55W - more powerful lamps melt the plastic of the diffuser.
  • 🛡️ Moisture protection: After replacement, check the drainage holes in the bumper (they often become clogged with dirt).

For replacement H11:

  1. Remove the plastic trim under the bumper (attached with 2 clips).
  2. Disconnect the power connector from the lamp by turning it counterclockwise.
  3. Unscrew the lamp from the socket and install a new one without touching the bulb.
💡

If the fog lights do not light after replacement, check the fuse F38 (15A) in the mounting block (located under the steering wheel). It often burns out when there is a short circuit in the circuit.

⚠️ Attention: In some versions Teana J31 (for example, with the option Fog Light Package) fog lights are connected via a relay. If the lamps are working but do not light, check the relay R17 in the fuse block.

Rear lights: brake lights, turn signals and license plate lights

In the taillights Teana J31 combination lamps are used P21/5W (brake light + clearance) and separate PY21W for turn signals. Replacing them is easier than in front optics, but there are pitfalls:

  • 🔧 Access: to get to the lamps, remove the trunk trim (it is attached to 4 plastic clips).
  • 🔄 Turn signals: lamps PY21W often “stick” to the cartridge - do not pull by force, but scroll them left and right.
  • 📛 Number plate illumination: lamps C5W or T10 change through the hatch in the trunk (unscrew 2 screws with a Phillips screwdriver).

For replacement P21/5W:

  1. Turn the cartridge counterclockwise and remove it.
  2. Click on the lamp and rotate it 90° to the left.
  3. Install a new lamp (make sure the contacts match the connector).
What to do if the brake lights are dim?

Dim brake light in Teana J31 is often associated with oxidation of the contacts in the socket or a voltage drop in the circuit. Check:

1. Condition of the contacts in the connector (clean with sandpaper if necessary).

2. The voltage on the lamp when you press the brake must be at least 11.5V (measured with a multimeter).

3. Fuse F22 (10A) in the cabin unit.

If the problem persists, the brake light switch (located under the brake pedal) may be faulty.

Common mistakes when replacing lamps and how to avoid them

Even experienced car owners make mistakes that lead to lamp burnout, short circuit or damage to the headlight. Here are the most common:

  • 🧤 Touching the flask with bare hands - grease marks on halogen lamps (H7, H11) lead to local overheating and reduce service life by 30–40%. Use gloves or a cloth.
  • ⚡ Ignoring polarity - lamps P21/5W (brake lights) have two contacts. If you confuse “+” and “–”, the marker will light up, but the brake light will not.
  • 🔧 Use of force - plinths D2S (xenon) often “stick” to the headlight unit. Don't try to unscrew them with pliers - use rubber gloves for better grip.
  • 💡 Installing LED instead of halogen - LED lamps in H7 or H11 without modifying the reflector, they produce an incorrect light beam and blind oncoming drivers.

Another common problem is condensation in the headlight after replacing the lamp. This happens due to:

  • 🚿 The headlight cover is not tightly closed (check the O-ring).
  • 🕳️ Clogged drainage holes in the bottom of the headlight (clean with wire).
  • 🔥 Lamp overheating (for example, if H7 100W instead of standard 55W).
💡

If after replacing the lamp it burns out within a week, the reason is either a defect or a power surge in the on-board network. Check the generator and voltage regulator relay (normal: 13.8–14.4V).

Where to buy lamps for Nissan Teana J31: trusted sellers

When purchasing lamps for Teana J31 It is important to avoid fakes. Focus on the following features of original products:

  • 🏷️ Packaging: y Philips And Osram There is a hologram and production date on the box.
  • 🔍 Base: on original lamps marking (H7, D2S etc.) is clearly stamped, without blurred edges.
  • 📄 Documentation: The kit must contain instructions in Russian or English.

Recommended places to buy:

Store type Pros Cons Example
Official dealer Nissan 100% original, guaranteed Prices are 2–3 times higher than market prices nissan.ru
Online marketplaces Wide range, reviews Risk of running into a fake Wildberries, Ozon, Exist.ru
Specialized auto stores Expert consultation, check before purchase Limited assortment Autolight, LightOnline

⚠️ Attention: When purchasing xenon lamps D2S on the market or in unverified online stores there is a risk of running into counterfeit, which not only shines worse, but can also damage the ignition unit. Check the certificate of conformity (there must be a marking ECE R99).

FAQ: answers to frequently asked questions

Is it possible to install LED lamps in low beam instead of halogen?

Technically yes, but this violates traffic rules (clause 3.6 List of faults). LED lamps in a halogen reflector produce an incorrect light beam that blinds oncoming drivers. Legal option - installation certified LED modules with a lens (for example, Morimoto 2Stroke), but this requires re-registration with the traffic police.

Why do H7 lamps often burn out in Teana J31?

Common reasons:

  1. Voltage surges in the on-board network (check the generator and relay regulator).
  2. Poor contact in the cartridge (oxidation or burning).
  3. Vibrations (for example, when driving on bad roads) - try lamps with a reinforced base (Osram Ultra Life).
  4. The quality of the lamps is cheap analogues (Mayak, Diode) serve 2–3 times less than the original.
How can I check if my Teana J31 has xenon or halogen?

Determination methods:

  • 🔍 Look at the headlight: xenon has lens and inscription D2S on the body.
  • 💡 Turn on the low beam: xenon lights up with a delay of 1-2 seconds (ignition time).
  • 📄 Check the car's VIN through the service Nissan TechInfo — the description of the options will indicate the type of optics.
What should I do if the light is dim after replacing the H7 lamp?

Possible causes and solutions:

  • 🔋 Weak battery — at voltages below 12V, the lamps glow dimly. Check the battery charge.
  • 🔌 Oxidation of contacts — clean the lamp socket and connector with sandpaper.
  • 💡 Rejection of a lamp — try installing another one (preferably from a trusted brand).
  • 🔦 Reflector clouding — over time it loses its reflective properties. The solution is to polish or replace the headlight unit.
Is it possible to adjust the headlights yourself after replacing the bulbs?

Yes, but it will be required flat area and a vertical wall. Algorithm:

  1. Park the car 5 meters from the wall.
  2. Place marks on the wall in the center of each headlight (at the height of the lamps).
  3. Rotate the adjusting screws on the headlamp (they are located on the top and side) until the light spot matches the marks.

For xenon (D2S) adjustment is required - incorrect adjustment will blind oncoming drivers.