Nissan Juke is one of the most recognizable crossovers on the road thanks to its futuristic design. But even such a stylish car has weak points, and the trunk lid (or, as it is also called, the “fifth door”) is one of them. Owners often encounter problems: from banal creaking hinges to serious malfunctions of the lock or power steering. In this article we will look at everything you need to know about the trunk lid. Juke - from diagnosing breakdowns to complete replacement and tuning.

The material will be useful for both beginners and experienced car owners. We will not just list typical problems, but give step-by-step instructions with photos, art. numbers of original and analog spare parts, and we will also tell you how to save on repairs without losing quality. We will pay special attention to models Juke F15 (2010–2019) and Juke F16 (2019–present), as their designs have key differences.

Trunk lid design Nissan Juke: what's inside?

trunk lid Juke - it's not just a piece of metal on hinges. It includes several key elements, each of which can fail:

  • 🔧 Loops - provide opening/closing. On Juke gas shock absorbers (hydraulic boosters) are used, which lose their tightness over time.
  • 🔒 Lock and drive — electromechanical unit responsible for fixation. Often breaks due to oxidation of contacts or wear of plastic parts.
  • 🎨 Sheathing and seals - protect from moisture and noise. Over time, the rubber hardens and the plastic cracks.
  • 💡 Electronics — opening sensor, license plate illumination, rear view camera (on top trim levels).

On Juke F15 (first generation) the trunk lid is mounted on two hinges with gas shock absorbers D1060-4XB0A (original) or SACHS 100 334 (analog). B Juke F16 (second generation) the design became more complicated: an electric lock drive appeared with art. 285B0-4M000, and the shock absorbers became more powerful due to the increased weight of the door.

📊 What generation of Nissan Juke do you have?
  • Juke F15 (2010–2019)
  • Juke F16 (2019–present)
  • Haven't decided on a purchase yet
  • Another Nissan

It is important to understand that the trunk lid Juke - this is system node. For example, if the lock does not work, the problem may not lie in the lock itself, but in the body control unit (BCM) or fuse F37 (10A) in the mounting block.

Typical malfunctions: symptoms and causes

Problems with the trunk lid Nissan Juke divided into mechanical and electrical. Let's look at the most common ones:

Symptom Probable Cause Difficulty of repair
The lid does not open with the button on the key The lock drive is faulty, the battery is dead, the fuse is blown F37 Average
Creaking or knocking noise when opening Wear of hinges or gas shock absorbers, lack of lubrication Light
The lid falls or does not stay open Damage to gas shock absorbers, loosening of fastenings Average
Water inside the trunk The seal is damaged or the drainage holes are clogged with dirt. Light
Number plate illumination does not work Burnt out light bulb 7440, contacts are oxidized, wiring is broken Light

A critical feature of the Juke: on models with a rear view camera (optional B92) when replacing the trunk lid, the parking assistance system must be recalibrated via a diagnostic scanner (for example, Launch X431). Ignoring this will lead to incorrect operation of the sensors.

⚠️ Attention! If the trunk lid Juke suddenly stopped opening, do not try to pull it by force. On models with electric drive, this can lead to cable breakage or gearbox failure. First check the fuse and voltage at the drive (should be 12V when pressing the button).

How to remove the trunk lid Nissan Juke: step by step instructions

To remove the trunk lid you will need:

  • 🔧 Socket wrenches on 10 And 12.
  • 🔧 Screwdriver with flat and cross blade.
  • 🔧 Plastic spatulas for removing trim.
  • 🔧 Marker for marks (when removing gas shock absorbers).

Procedure:

  1. Disconnect the battery (remove the negative terminal) to avoid short circuit when working with electrical wiring.
  2. Remove the trim:
    • Remove the two screws under the plastic plugs at the bottom of the cover.
    • Carefully pry up the trim with a spatula, starting at the corners. Be careful - on Juke F16 The rear view camera wires run under the trim.
  3. Disconnect electronics:
    • Disconnect the power supply chips for the license plate light, lock and (if any) camera.
    • On Juke F15 The lock feature may be hidden under a plastic cover - it needs to be moved to the side.
  4. Remove gas shock absorbers:
    • Support the lid (it's heavy!). Mark the position of the hinges with a marker so as not to disturb the geometry during assembly.
    • Unscrew the bolts securing the shock absorbers to the body and cover (key on 10).
  5. Unscrew the hinges:
    • The hinges are secured with four bolts on 12 (two on each side). Start with the bottom bolts, then the top ones.
    • When removing the cover, hold it - it may fall sharply if the shock absorbers are already faulty.

Disconnected the battery|Took pictures of the location of the chips and bolts|Prepared a support for the lid (table, assistant)|Checked the availability of tools (keys 10 and 12, spatulas)-->

Assembly takes the same amount of time as disassembly. The main thing is not to overtighten the hinge bolts (tightening torque 20–25 Nm) and make sure that all the chips are connected correctly. If the lid is difficult to open after installation, check the lubrication of the hinges (LIQUI MOLY LM47 will fit perfectly).

Replacing gas shock absorbers: when and how?

Gas shock absorbers (aka “gas lifts”) on Nissan Juke designed for 50–80 thousand opening cycles. But in Russian realities (frost, dirt, aggressive operation) they fail after 3–4 years. Signs of malfunction:

  • 🚪 The trunk lid falls when opening.
  • 💨 It takes effort to lift it.
  • 🔊 Hissing or knocking appears when shock absorbers operate.

For replacement, the original shock absorbers will be suitable (D1060-4XB0A for F15 And D1060-4M000 for F16), and analogues:

Brand Article Price (2026) Features
SACHS 100 334 ~1,200 rub./pcs. Good quality, but the first weeks can be a bit harsh.
Stabilus 0826NX ~1,500 rub./pcs. Soft operation, long service life.
Lesjöfors 100334 ~900 RUR/pcs. Budget option, but the resource is lower.

How to replace:

  1. Lift the trunk lid and secure it with a stop (for example, a wooden block).
  2. Unscrew the lower mount of the shock absorber to the body (bolt on 10).
  3. Remove the top fastening to the cover. Help may be needed here - hold the shock absorber so that it does not tear out the mount.
  4. Install the new shock absorber in reverse order. Important! On Juke F16 The right and left shock absorbers are different - do not mix up the sides.
💡

Before installing new shock absorbers, apply a little grease to the ball joints - this will extend their service life and eliminate squeaks.

⚠️ Attention! If, after replacing the shock absorbers, the trunk lid opens too easily and “shoots” upward, it means that you have installed too powerful parts. This is dangerous - the hinges may burst over time. Optimal force: the lid should open smoothly, without jerking, and be locked in any position.

Trunk lock repair: from cleaning to complete replacement

Trunk lid lock Nissan Juke - one of the most vulnerable places. On F15 The plastic drive gear often breaks, and F16 — the contacts of the electric motor are oxidized. Let's look at typical problems and solutions:

  • 🔑 The lock does not open with a button, but it works with a key → There is a problem with the drive or wiring. Check the fuse F37 and voltage on the drive chip (should be 12V when pressing the button).
  • 🔊 Clicks when opening, but the lock does not work → Wear of plastic parts of the mechanism. Requires disassembly and replacement of gear (art. 285B0-4M010).
  • 💧 The lock jammed after washing → Contacts are oxidized or water gets into the mechanism. Needs to be dried and lubricated WD-40.

How to disassemble the lock:

  1. Remove the trunk lid trim (see instructions above).
  2. Disconnect the power supply from the lock drive.
  3. Unscrew the three bolts securing the lock (the key is on 10).
  4. Remove the mechanism and disassemble it by removing the plastic cover (it is held on by latches).

Inside you will see a gear and an electric motor. If the gear is broken, it can be replaced separately (art. 285B0-4M010 for F16). If the motor burns out, you will have to change the entire drive (285B0-4M000, price ~5,000 rub.).

What to do if the lock is stuck in the closed position?

If the trunk lid does not open with either the button or the key, try the following:

1. Remove the rear parcel shelf (it is secured with clips).

2. Through the technological hole, try to get to the emergency opening cable (it is usually red).

3. Pull the cable - this will unlock the lock.

If there is no cable, you will have to remove the driver's door trim and manually apply voltage to the lock actuator (red wire - "+", black - "-").

On Juke F16 after replacing the lock it may be necessary key programming (if the lock control unit has been replaced). This can only be done at a service station with diagnostic equipment (Nissan Consult or Launch X431).

Tuning the trunk lid: from spoiler to LEDs

trunk lid Nissan Juke - an excellent object for tuning. Here are some popular modifications:

  • 🎨 Coil springs instead of gas shock absorbers - Allows you to adjust the opening force. Popular set: StrongArm (art. SA-JUKE, price ~6,000 rub.).
  • 💡 LED number plate illumination - instead of standard lamps 7440 install LED modules (Osram LEDriving). Important: on F16 It may be necessary to install resistors to avoid errors on the tidy.
  • 🚀 Spoiler or wing — improves appearance and aerodynamics. Popular models: Evo-R or Seibon Carbon (from 15,000 rub.).
  • 🔒 Electronic lock with remote control - for example, Pop & Lock (art. PL8230). Allows you to open the trunk using the key fob.

Important when tuning:

  • Any changes in the electrical circuit (LED, additional locks) may cause errors on the dashboard. Use kan filters or resistors to simulate a load.
  • Installing a spoiler may affect the operation of the rear view camera. You may have to reconfigure the viewing angle through the diagnostic scanner.
  • If you are installing aftermarket gas shock absorbers, check their compatibility with the weight of the cover. Too powerful ones can deform the hinges.
💡

Before any tuning of the trunk lid Juke check whether it will affect the warranty (if the car is under warranty) or MOT. For example, LED lamps in the license plate illumination may cause a technical inspection refusal.

Prices for repairs and spare parts: where is it cheaper?

Cost of trunk lid repair Nissan Juke depends on the type of fault and method of elimination. Below are the estimated prices for 2026:

Type of work/spare parts Price (by yourself) Price (STO) Notes
Replacing gas shock absorbers (pair) 2,400–4,000 rub. 4,000–7,000 rub. The cost depends on the brand (original vs analogue).
Lock repair (gear replacement) 1,500–2,500 rub. RUB 3,500–5,000 On F16 programming may be required.
Replacing the lock drive 5,000–7,000 rub. 8,000–12,000 rub. Includes the cost of the part (~5,000 rub.) and labor.
Eliminating squeaky hinges 200–500 rub. 1,000–1,500 rub. Requires lubrication LIQUI MOLY LM47 or analogues.
Complete replacement of the trunk lid (used) 15,000–30,000 rub. 25,000–40,000 rub. The price depends on the condition and configuration (with/without camera).

Where to buy spare parts:

  • 🛒 Original - official dealers Nissan or trusted online stores (Exist.ru, Autodoc).
  • 🛒 Analogues — SACHS, Stabilus, Febi. Pay attention to reviews - some cheap shock absorbers last less than a year.
  • 🛒 Used spare parts — Avito, Drom.ru, disassembly. There is a risk of running into a “pig in a poke”, but you can save up to 50%.

Saving tip: If you need to replace the entire trunk lid, look for options from disassembly, but be sure to check:

  • Condition of hinges and shock absorbers.
  • Functionality of the lock and electronics.
  • No corrosion (especially in the places where the hinges are attached).

Frequently asked questions about the trunk lid Nissan Juke

Is it possible to open the trunk if the battery is dead?

Yes, but the method depends on the model:

  • On Juke F15 There is a mechanical key in the key fob - insert it into the lock on the trunk lid.
  • On Juke F16 There is no mechanical lock. You will have to either “light” the car, or remove the rear parcel shelf trim and pull the emergency release cable.
Why does the trunk lid open by itself while driving?

This is a dangerous malfunction! Reasons:

  • The lock is worn or broken (does not secure the lid).
  • Microswitch in the lock is faulty (the opening signal is false).
  • Problems with the body control unit (BCM).

Contact the service station immediately! You cannot drive with such a malfunction.

How to eliminate creaking hinges?

Creaking occurs due to lack of lubrication or corrosion. Proceed like this:

  1. Clean the hinges from dirt (you can use WD-40).
  2. Apply high temperature grease (LIQUI MOLY LM47 or Molykote G-4500).
  3. If the squeak remains, check the play in the hinges - replacement may be required.
Can a Juke F16 trunk lid be installed on a Juke F15?

Technically yes, but there are some nuances:

  • The hinge mounts are the same, but the shock absorber mounts may differ.
  • The electronics (lock, camera) may not be suitable - the wiring will need to be modified.
  • The design of the lids is different, which will affect the appearance.

We recommend looking for the cover for your model.

What should I do if, after replacing the shock absorbers, the trunk lid opens too tightly?

Probable reasons:

  • Shock absorbers installed are too weak (check the article number).
  • The hinges were skewed during installation (need to be adjusted).
  • The guides are jammed in the hinges (lubricate LIQUI MOLY).

If the problem is in the shock absorbers, they will have to be replaced with more powerful ones.