Nissan X-Trail T31 is one of the most popular crossovers on the Russian market, and its trunk experiences serious loads every day. The trunk lid (or "fifth door") in this model not only provides access to the cargo compartment, but also affects aerodynamics, safety and even ride comfort. However, over time, it can fail: from banal wear of the seals to serious damage after an accident or corrosion.
In this article we will look at all the nuances associated with the trunk lid. X-Trail T31 (2007–2013): how to choose an original or non-original part, which part numbers are relevant in 2026, how to carry out replacement or repair yourself, and what pitfalls may arise in the process. We will place special emphasis on typical problems that owners encounter and ways to solve them without contacting service.
Original and non-original trunk lids: what to choose?
When purchasing a new trunk lid for Nissan X-Trail T31 The owner has a choice: an original part from the manufacturer or an analogue from third-party brands. Both options have their pros and cons, and the final decision depends on the budget, quality requirements and delivery time.
Original covers supplied from factory Nissan and guarantee perfect fit, compatibility with electronics (if provided) and durability. However, their cost can reach 40–60 thousand rubles (depending on the configuration and color), and delivery times from Japan or Europe often exceed 1–2 months. Main articles of original covers for T31:
- 🔹
62601-4M00A— trunk lid without windshield wiper (basic equipment) - 🔹
62601-4M00B- cover with windshield wiper and heated glass - 🔹
62601-4M01A- option for models with rear spoiler - 🔹
62601-4M02A— cover with an integrated rear view camera (for top versions)
Non-original analogues are cheaper (from 15 to 30 thousand rubles), but here it is important to pay attention to the manufacturer. Among the trusted brands:
- 🔧 Febi (Germany) - high quality, but the price is close to the original
- 🔧 AMS (Taiwan) - optimal price/quality ratio
- 🔧 Keen Parts (China) - a budget option, but requires modification of the landing
- 🔧 Danto (South Korea) - a good alternative to the original, often comes with seals
⚠️ Attention: When purchasing a non-original cover, be sure to check VIN code your X-Trail T31 with the seller's catalogue. Even minor differences in year or trim level can cause installation problems (such as mismatched windshield wiper or rear wiper mounts).
- Original (expensive, but reliable)
- Non-original (cheaper, but risk of defects)
- Used in good condition (economical)
- I don't know, I haven't decided yet
When does a trunk lid need to be replaced?
Replacing the trunk lid with Nissan X-Trail T31 - not the most common procedure, but in some cases it becomes a necessity. Here are the main signs that it’s time to change the part:
- 🚗 Serious mechanical damage after an accident (cracks, metal deformation, damage to fasteners). Even if the lid looks intact on the outside, internal distortions can disrupt the tightness and operation of the locks.
- 🔥 Corrosion, especially at welds or near seals. X-Trail T31 It is not uncommon to suffer from rust in the rear of the body, and if the process has progressed too far, repair may not be practical.
- 🔌 Electronics problems: The rear wiper, heated glass or license plate lights do not work. This is often due to damaged wiring inside the cover.
- 🔒 Worn or broken lock, if it cannot be repaired (for example, if the central locking mechanism or electronics are damaged).
In some cases you can get by partial renovation. For example, if only the glass is damaged, it can be replaced separately (item no. 62602-4M00A). The same goes for seals (62610-4M000), gas stops (62620-4M00A) or rear spoiler (62630-4M00A). However, if the damage is complex, it is cheaper and more reliable to install a new cover.
| Type of damage | Can it be repaired? | Repair cost (₽) | Replacement cost (₽) |
|---|---|---|---|
| Crack in glass | Yes (glass replacement) | 8 000–12 000 | — |
| Metal deformation (no rust) | Yes (straightening) | 15 000–25 000 | 40 000–60 000 |
| Corrosion (through) | No (replacement only) | — | 40 000–60 000 |
| Heated glass does not work | Yes (replacement of wiring or glass) | 5 000–10 000 | — |
| Lock failure | Sometimes (depending on model) | 3 000–8 000 | 40 000–60 000 |
If the trunk lid X-Trail T31 damaged as a result of an accident, be sure to check the geometry of the body before replacing it. Even a slight misalignment can lead to problems with installing a new part and a leak.
Step-by-step instructions for replacing the trunk lid
Replace the trunk lid with Nissan X-Trail T31 you can do it yourself if you have an assistant and a basic set of tools. The process takes about 3-4 hours and requires care, especially when working with wiring and gas stops.
Required tools:
- 🛠️ Socket wrenches for 10, 12 and 14 mm
- 🛠️ Screwdrivers (phillips and flathead)
- 🛠️Pliers and wire cutters
- 🛠️ Scotch tape or electrical tape (to secure the wiring)
- 🛠️ Lubricant for hinges (for example, WD-40 or LIQUI MOLY)
Work order:
- Disconnect the battery. This is mandatory for safety, since during dismantling you will be working with the wiring for the heated glass and rear wiper.
- Remove the inner cover trim. It is attached to plastic clips and screws (usually under decorative plugs). Use a flat-head screwdriver to carefully pry the clips to avoid breaking them.
- Disconnect the wiring. Connectors for the heated glass, rear wiper and license plate light are usually located on the right (passenger side). Memorize or photograph their location.
- Remove the gas struts. They are bolted on both sides. Hold the cover so that it does not fall after removing the stops!
- Unscrew the loop fastening bolts. There are usually 4 of them (2 for each loop). Here you will need a helper to hold the lid.
- Remove the old cover and install the new one in reverse order. Don't forget to move the seal and, if necessary, the lock with the cylinder.
Tightness of the seal (are there any gaps)|Operation of the rear wiper and heated glass|Fixation of the gas stops (the cover must be held in any position)|Central locking (opening/closing with the key fob)|License plate illumination-->
If you are installing a cover with rear view camera or parking sensor, you will additionally need:
- 📹 Lay the wiring for the camera (usually through the rubber seal in the trunk).
- 📶 Connect the sensor to the control unit (reflashing may be required ECU).
- 🔧 Set up the camera in the multimedia system menu (path:
Settings → Camera → Calibration).
⚠️ Attention: When installing a cover with a rear view camera on a model that did not originally have one, you will need to replace the inner trunk lining (part number 62650-4M00A) - it has holes for wiring. Without this, the cable will have to be laid outside, which is unaesthetic and unreliable.
Typical trunk lid problems and their solutions
Even if the trunk lid Nissan X-Trail T31 is not damaged, various problems may arise with it. Let's look at the most common ones and how to eliminate them.
1. The lid cannot be opened from the interior or from the key fob
Most often this is due to breakdown of the central locking drive or cable break. Check:
- 🔑 Does central locking work on other doors? If not, the problem is in the control unit (BCM).
- 🔧 Is there mechanical resistance when trying to open the lid with a key? If so, the lock may be jammed.
- 🔋 Check the fuse
F30 (10A)in the block under the steering wheel - it is responsible for powering the trunk lock.
If the cable is torn, it can be replaced (part no. 62640-4M00A). To do this, you will have to remove the lid trim and the rear trunk panel.
2. The lid falls off or does not stay open
The culprits are gas struts (shock absorbers). Over time, they lose pressure and no longer hold the lid. Replacing a pair of stops will cost 1,500–2,500 rubles (article 62620-4M00A for left and right).
If the stops are in order, but the cover still sags, check:
- 🔩 Hinge fastenings - the bolts may have loosened.
- 🔧 Condition of the hinges - they may rust or become deformed.
- 📏 Body geometry - if the trunk was damaged in an accident, the lid may not fit correctly on the stops.
3. Water leaking into the trunk
If water appears in the trunk after rain, the problem lies in lid seal or clogged drain holes. To fix a leak:
- Clean the drainage channels at the bottom of the lid (they often become clogged with leaves and dirt).
- Check the seal for cracks or deformation. Replace it if necessary (part no.
62610-4M000, price ~2,000 ₽). - Apply silicone grease to the seal to restore elasticity.
How to check the tightness of the trunk lid without rain?
Use a watering hose or watering can, directing a stream of water to the junction of the cover and body. An assistant should be inside the trunk and monitor the appearance of drops. Pay special attention to the corners and the area near the rear lights - leaks most often occur there.
4. Heated glass or rear wiper does not work
If the heated glass does not turn on, check:
- 🔌 Fuse
F20 (15A)in the fuse block. - 🔧 Connectors on the cover - they may oxidize or come off.
- 📡 The heating elements themselves (using a tester). If the threads are burnt out, the glass will need to be replaced.
Typical problems for the rear wiper:
- 🔧 Brush wear (replacement ~500 ₽).
- 🔧 Motor failure (article no.
28550-4M00A, price ~3,500 ₽). - 🔧 Broken wiring in the corrugation between the cover and the body.
If the rear wiper is on X-Trail T31 works jerkily or slowly, lubricate its axle with silicone grease. This often solves the problem without replacing the motor.
Trunk lid repair: when is it cheaper than replacement?
Replacing the trunk lid is not always economically justified. In some cases renovation costs less and allows you to save the original part. Let's look at when this is appropriate.
1. Straightening and painting for minor damage
If the cover is dented, but the metal is not torn and there is no through corrosion, it can be repaired. Average cost of straightening and painting:
- 🔨 Local repair (1–2 dents) — 5 000–10 000 ₽.
- 🔨 Full straightening with painting - 15 000–25 000 ₽.
Important: after straightening, check the work lock and gas stops - metal deformation can affect their functioning.
2. Elimination of corrosion
If rust has just begun to appear, it can be removed and problem areas treated. To do this:
- Sand the rust down to bare metal (with sandpaper or a brush).
- Treat the surface with a rust converter (for example, Tsinkar).
- Apply primer and paint the problem area.
- For additional protection, use an anti-corrosion mastic (for example, Molicote).
If the corrosion is through, repair is only possible with welding and patching, but this is a temporary solution. In the long term, such a cover will still require replacement.
3. Electronics repair
If the heated glass, rear wiper or license plate lights do not work, it is often to blame wiring in the corrugation between the cover and the body. To repair it:
- Remove the corrugation and check the integrity of the wires.
- Clean and insulate damaged areas.
- If necessary, replace the corrugation (part number
62660-4M00A, price ~1,200 ₽).
If the problem is control unit (for example, the rear view camera does not work), it may require flashing or replacement. In this case, it is better to contact an auto electrician.
⚠️ Attention: When repairing trunk lid wiring X-Trail T31 never use twists! Soldering only or special automotive terminals (for example, Wago 221). Twists oxidize over time and can cause a short circuit.
Caring for the trunk lid: how to extend its service life?
To the trunk lid Nissan X-Trail T31 served for a long time, just follow a few simple recommendations:
- 🧼 Clean the seal regularly and apply silicone grease to it (1-2 times a year). This will prevent cracking and loss of elasticity.
- 🔧 Check gas struts every 50,000 km. If the lid starts to fall off, replace them with a pair (even if only one breaks).
- 🚿 Clean drain holes in the lower part of the cover from dirt and leaves (especially in autumn).
- 🔑 Lubricate the lock graphite lubricant once a year to avoid jamming.
- 🔋 Monitor the condition of the wiring in corrugation. If you notice cracks in the insulation, replace the corrugation or wires.
In winter, pay special attention to:
- ❄️ Heated glass - do not turn it on at maximum power for more than 10 minutes, this may lead to burnout of the threads.
- ❄️ Rear wiper — before winter, replace the brush with a new one and lubricate the axle.
- ❄️ Sealant - After washing, dry it to prevent ice from forming.
The most common cause of trunk lid failures X-Trail T31 — ignoring minor problems (creaks, smudges, weak stops). Regular inspection and prevention are less expensive than repair or replacement.
Where to buy a trunk lid for Nissan X-Trail T31?
When purchasing a trunk lid, it is important to choose a reliable supplier to avoid counterfeits or defects. Here are the main options:
1. Official dealers Nissan
Pros:
- ✅ 100% original part with guarantee.
- ✅ Exact color and configuration.
Cons:
- ❌ Highest price (from 40,000 ₽).
- ❌ Long delivery times (1-2 months).
2. Online spare parts stores
Popular platforms:
- 🌍 Exist.ru — a wide range of original and non-original parts.
- 🌍 Emex.ru — there are often promotional offers.
- 🌍 JP-CarParts — specializes in Japanese cars.
Tip: when ordering, please check whether it is included in the package seal, gas struts and lock. Often they have to be purchased separately.
3. Disassembly and used parts
Pros:
- ✅ The price is 2-3 times lower than new (from 10,000 ₽).
- ✅ Fast delivery (if disassembly is in your city).
Cons:
- ❌ Risk of hidden defects (corrosion, damage after an accident).
- ❌ There is no warranty for the part.
Where to look:
- 🔍 Avito — check reviews about the seller.
- 🔍 Drom.ru — there is a filter by model and year.
- 🔍 Local groups in VK or Facebook (for example, "Disassembly of Nissan Moscow").
⚠️ Attention: When purchasing a used trunk lid, be sure to check it for hidden corrosion (especially in welding areas and under the seal) and geometry (attach a ruler to the edges - they should be even). If the cover was painted, ask why (accident or cosmetic repairs).
FAQ: Frequently asked questions about the trunk lid Nissan X-Trail T31
Is it possible to install a trunk lid from Nissan X-Trail T32 on T31?
No, these models have different bodies and the covers are not interchangeable. U T32 different rear shape, different hinges and electronics. Even if they look similar in appearance, installing a cover from T32 on T31 technically impossible without serious modification of the body.
What paint color is suitable for the trunk lid? X-Trail T31 2010?
The color depends on your vehicle's paint code. On X-Trail T31 the most common:
KH3— "Titanium gray"BQ5- "Deep Blue"KAD- "Black"AY9- "Silver"
The exact code is indicated on a plate under the hood (on the driver's side of the body). When ordering a cover, please specify this code to avoid color mismatches.
What should I do if the central locking does not work after replacing the trunk lid?
Most likely the problem is one of the following:
- The wiring connector is not connected to the new lock.
- The wires are mixed up when connecting (check the diagram for your configuration).
- It is necessary to “train” a new lock (on some versions X-Trail T31 error reset via diagnostic scanner is required).
- The central locking control unit has failed (BCM).
First check the wiring connection, then try to calibrate the lock through the on-board computer menu (if such a function is provided).
Can I paint the trunk lid myself?
Yes, but for a quality result you will need:
- Sandblasting (or thorough sanding
P80–P120). - Primer (preferably epoxy, for example, Novol Protect 340).
- Spray paint or spray gun (the color must exactly match the body code).
- Varnish (for protection and shine).
- Polish after drying.
If you do not have experience, it is better to contact a car service - painting yourself without equipment often leads to smudges and uneven color.
How much does the trunk lid weigh? Nissan X-Trail T31?
The weight of the cover depends on the configuration:
- Basic version (without heated glass and wiper) - 12–14 kg.
- Cover with heating and wiper - 15–17 kg.
- Version with rear view camera - up to 18 kg.
When dismantling, take into account the weight - it is difficult to remove the cover without an assistant, especially if the gas stops no longer work.