Fastening the rear bumper of the <em>Nissan Almera N16</em>: complete instructions with photos and diagrams

Rear bumper Nissan Almera N16 - This is not only a design element, but also an important part of the body that protects the car from damage. Over time, bumper mounts wear out, break in an accident, or simply require replacement due to corrosion. If you notice that the bumper is sagging, squeaking or does not fit well, it must be removed for repair or complete replacement.

In this article we will look in detail all stages of dismantling and installing the rear bumper on Almera N16 (2000–2006), including hidden fastenings, typical mistakes and tips for choosing spare parts. The instructions are suitable for both a sedan and a hatchback - the differences in fastenings are minimal. If you plan to do this yourself, prepare the tools and 1-2 hours of free time.

Rear bumper design Nissan Almera N16: schemes and features

Bumper Almera N16 attached to the body using 6–8 fixation points, some of which are hidden under the trunk trim and wheel arches. Main design elements:

• 🔧 M8 bolts — attach the bumper to the side members (2 pieces, one on each side).
• 🔩 Self-tapping screws — fix the bumper to the fender liners (2-3 pieces per side).
• 🔗 Plastic clips — connect the bumper to the lower part of the body (4–6 pcs.).
• 🚗 Latches — hold the bumper in the central part (under the license plate).

Feature Almera N16 — There are no fastenings under the headlights, which simplifies dismantling, but requires caution when working with clips. If they are broken, the bumper will be loose or loose. On the hatchback there are additionally 2 bolts under the rear door, which are often forgotten to unscrew.

Mounting type	Quantity	Location	Tool
M8 bolts	2	Spars (under the trunk)	10 mm head
Self-tapping screws	4–6	Lockers	Phillips screwdriver
Plastic clips	6	Bottom of bumper	Flat head screwdriver
Latches	2	Under the license plate	Hands (gently pressing)

The mountings on the sedan and hatchback are identical, with the exception of two additional bolts on the hatchback (under the rear door). If you are working with Almera N16 after 2003, pay attention to the modification of the bumper - in some versions the clips may differ in shape.

Required tools and materials

For removing and installing the rear bumper Nissan Almera N16 you will need:

• 🔧 10 mm head with extension (for side member bolts).
• 🔩 Phillips screwdriver (for self-tapping screws in arches).
• 🪛 Flat head screwdriver (for prying off the clips).
• 🧲 Magnet (so as not to lose the bolts during dismantling).
• 🧴 WD-40 (if the fastenings are rusty).
• 🔨 Plastic puller (optional, for gentle removal of clips).

If you plan to replace the bumper, buy in advance new clips and screws - old ones often break during dismantling. Original spare parts for Almera N16 can be found by article number:

• 📌 Bumper clip — 77110-4M000 (set of 10 pcs.).
• 📌 Bolt M8 — 08905-60010 (with washer).
• 📌 Self-tapping screw for arches - 08126-45010.

Step-by-step instructions: how to remove the rear bumper

Removing the bumper Nissan Almera N16 takes 30–40 minutes. Follow the instructions to avoid damage:

1. Open the trunk and remove the trim from the inside of the rear panel. To do this, pull it towards you (it is held on by clips).
2. Unscrew 2 M8 bolts on each side (under the trunk, near the side members). Use a 10mm socket with an extension.
3. Remove the wheel arches (3 screws on each side). This will provide access to the screws securing the bumper to the fender liners.
4. Detach the clips at the bottom of the bumper. Pry them out with a flat-head screwdriver, but do not pull sharply - the plastic is fragile!
5. Release the latches under the license plate (gently press the bumper from the inside).
6. Remove the bumper, pulling it towards you. If it does not budge, check that all fasteners are unscrewed.

On a hatchback, additionally unscrew 2 bolts under the rear door (they are hidden under a plastic plug). If the bumper is stuck to the body, treat the fasteners WD-40 and wait 5-10 minutes.

⚠️ Attention: Do not pull on the corners of the bumper as this may break the plastic clips. Start removing from one side, gradually releasing the clips.

Common mistakes and how to avoid them

When working with a bumper Nissan Almera N16 Car owners often make the same mistakes:

• 🔧 Broken clips — if you pull the bumper sharply, the plastic clips break. Solution: use a plastic puller or pry off the clips carefully.
• 🔩 Lost bolts — M8 bolts are easy to fall into the spar. Solution: use a magnet or place a rag.
• 🚗 Unscrewed screws in arches — if you forget about them, the bumper will not come off. Solution: check all attachment points according to the diagram.
• 🔥 Damaged wiring (on versions with PTF). Solution: Disconnect the battery terminals before operation.

Another common problem is loose fit of the bumper after installation. This happens due to:

• 🔄 Incorrectly installed clips (skewed or not fully latched).
• 🔧 Loose M8 bolts (must be tightened with a force of 8–10 Nm).
• 🚗 Deformed bumper (may require straightening after an accident).

What to do if the bumper cannot be removed?

If the bumper does not budge, check again:

- Are all M8 bolts unscrewed (sometimes one goes unnoticed).

- Are the clips at the bottom disconnected (there may be more of them than in the diagram).

- Does the wiring from the fog lights interfere (on some versions).

If everything is unscrewed, but the bumper does not come off, gently shake it left and right to release the latches.

Installing the rear bumper: nuances and tips

Bumper installation Nissan Almera N16 easier to dismantle, but requires care:

1. Place the bumper on the body, aligning the holes for the M8 bolts.
2. Secure the clips at the bottom (they should click).
3. Tighten M8 bolts (do not overtighten so as not to break the thread!).
4. Install self-tapping screws in the arches and put the fender liners back in place.
5. Check clearances — the bumper should fit evenly around the entire perimeter.

If you have Almera N16 with fog lights, before installing the bumper, connect the PTF connectors and check their operation. On a hatchback, do not forget about the 2 bolts under the rear door - they are easy to miss.

⚠️ Attention: After installing the bumper, check the operation of the rear lights. If the contacts become oxidized during dismantling, clean them with alcohol or WD-40 Contact Cleaner.

Choosing a new bumper: original vs. analogue

If your bumper is damaged and requires replacement, you are faced with a choice: buy original part or analogue. Let's compare the options:

Criterion	Original bumper	Analog (non-original)
Price	15 000–25 000 ₽	5 000–12 000 ₽
Plastic quality	High (resistant to UV and frost)	Medium (may crack over time)
Compatibility	100% (exact fit)	90–95% (may require improvement)
Warranty	1–2 years	6–12 months

Original bumpers for Almera N16 are produced under the article numbers:

• 📌 Sedan: 62610-4M000 (without PTF) or 62610-4M001 (with PTF).
• 📌 Hatchback: 62630-4M000.

If your budget is limited, you can consider analogues from Febi, Hella or Dello. The main thing is to check reviews for a specific model, as quality can vary greatly. When purchasing, check whether the kit includes clips and bolts - often you have to buy them separately.

Frequently asked questions about bumper mounting Nissan Almera N16

Is it possible to remove the bumper without removing the wheel arches?

Technically yes, but it will make the task much more difficult. The screws in the arches will be inaccessible, and you will have to “break out” the bumper, risking breaking the clips. It’s better to spend 5 minutes removing the fender liners - this will save time and nerves.

What is the tightening torque for M8 bolts?

Recommended moment - 8–10 Nm. You should not overtighten, as you can break the threads in the spar. If you don't have a torque wrench, tighten the bolts finger-tight with moderate force.

What should I do if the clips break during removal?

You'll have to buy new ones (item number 77110-4M000). Don't try to use old ones - even if they look intact, their fixation will be unreliable. One broken clip can cause the bumper to vibrate at speed.

How to remove the bumper if the bolts are rusty?

Treat the fasteners WD-40 or liquid key and wait 10–15 minutes. If the bolt does not budge, try screwing a nut onto it (to strengthen the grip) and unscrew it again. As a last resort, cut it with a grinder, but this will require subsequent cutting of a new thread.

Do I need to remove the bumper to replace the tail lights?

No, just unscrew the screws securing the light from the trunk and disconnect the connector. It is not necessary to remove the bumper, but if access is difficult (for example, on a hatchback), it can be bent a little.