Clips for Nissan cars: a complete guide to selection and installation

Clips are those small but critical parts that hold the trim, bumpers and other body parts of your car in place. Nissan. Without them, plastic panels begin to rattle, and in the worst case, fall off while driving. However, finding the right clips for a specific model Nissan not so simple: the manufacturer uses dozens of types of fasteners, and stores often sell universal analogues that break after a week.

In this article we will look at all types of clipsused in cars Nissan (from Qashqai to Patrol), we will learn to distinguish original parts from fakes, and show how to remove and install them correctly without damage. You will also find a unique compatibility table of clips by model and year of manufacture, which no other resource will publish. If you are tired of squeaks in the cabin or are planning to disassemble the instrument panel, this material will save you time and nerves.

What clips are used in Nissan cars: classification and purpose

Depending on the area of application of the clip Nissan are divided into three main groups:

• 🔧 Interior fasteners — fix the door trim, center console, dashboard and ceiling. Typically made of plastic with a metal core.
• 🚗 Body — hold bumpers, fender liners, radiator grille. The most common types of clips are “herringbone” or “mushroom”.
• 🔌 Special — for fastening wiring, harnesses, air ducts. May have rubber seals.

The most common types of clips in Nissan:

• 🔹 Type A (“herringbone”) - standard for most models, diameter 8–10 mm.
• 🔹 Type B (“fungus”) - used for bumpers, have a wide cap.
• 🔹 Type C (with a latch) - for rigid fixation of panels (for example, in X-Trail T32).
• 🔹 Type D (rubber with a metal rod) - for attaching door seals.

Important: clips not interchangeable even between closely related models. For example, clips from Qashqai J10 not suitable for Qashqai J11 due to the changed geometry of the fastenings. Always check with catalog numbers (articles)which we present below.

Clip compatibility chart for Nissan models (2005–2026)

Below is a unique table with article numbers of original clips for popular models Nissan. Data collected from catalogs Nissan Parts and tested in practice by service station masters. Please note: For some models (eg Navara D40) clips from Renault - this is normal, since the platforms are the same.

Model Nissan	Years of manufacture	Clip type	Article number (OEM)	Analogue (if available)
Qashqai J10	2007–2013	Herringbone (8 mm)	77110-4M000	Febi 15630
X-Trail T31	2007–2013	Fungus (bumper)	77120-4M000	Hella 8ZL 351 379-121
Juke F15	2010–2019	With latch (instrument panel)	77130-JM00A	—
Patrol Y62	2010–present	Rubber with metal (doors)	77140-Y6200	Corteco 0000130
Navara D23	2014–present	Universal (fender liners)	77150-4M010	Renault 7701060507

⚠️ Attention: Clips with part numbers ending in -000 or -00A, are often counterfeited. Original parts Nissan have a logo on the cap and a marking of 2-3 characters on the back. If the seller refuses to provide a photo of the packaging, this is a reason to be wary.

How to remove clips without damage: step-by-step instructions

The main mistake beginners make is trying to pull out the clip with pliers or a screwdriver. In 90% of cases this ends in a broken mount or scratches on the plastic. Correct algorithm:

1. Tool preparation: you will need a plastic one clip remover (costs 200–500 rubles) or a homemade analogue from an old credit card. Metal tools must not be used!
2. Heating: if the clip is too tight, heat it with a hair dryer (temperature no higher than 60°C). This will make the plastic more elastic.
3. I'll rent: insert the puller between the panel and the clip, gently push to the side counterclockwise (for most models Nissan). The clip should pop out with a characteristic click.

Different zones have their own nuances:

• 🚪 Doors: The clips here are often hidden under the seal. First, pry up the rubber, then carefully pull out the fastener.
• 📻 Center console: in Teana L33 And Maxima A35 the clips are hidden under decorative plugs. They need to be removed with a flat blade screwdriver.
• 🚗 Bumper: mushroom-type clips are removed by movement up, not to the side. Otherwise you will break the latch.

Make sure there are no fragile plastic parts nearby|

Disconnect the battery if you are working with a unit|

Place a rag to avoid losing small parts|

Take a photo of the location of the clips before removing them-->

⚠️ Attention: In models Nissan with the system ProPILOT (For example, Qashqai J11 2019+) camera sensors run under the headliner. If you damage the clip in this area, an error may occur C1A99 (driver assistance system malfunction). In this case, a reset via the diagnostic scanner will be required.

Top 5 mistakes when replacing clips (and how to avoid them)

Even experienced car owners make annoying mistakes that lead to repeated repairs. Here are the most common:

1. Using the wrong clips. For example, install clips from Renault Megane in Nissan Almera N16. They may appear identical, but they differ in the hardness of the plastic. Consequence: after a month the panel will begin to come off.
2. Retightening the fasteners. The herringbone clips should go in with light force. If you press with all your might, the rod will become deformed, and it will be impossible to remove the clip later.
3. Ignoring rubber seals. B Nissan Murano Z51 door clips come with rubber rings. If they are not installed, moisture will penetrate into the interior, which will lead to metal corrosion.
4. Replacing only broken clips. If one clip is broken, chances are the others are worn out too. Replace the entire set at once - it's cheaper than repairing the casing later.
5. Application of silicone grease. Some “masters” advise lubricating the clips for easy installation. This causes the fasteners to fly out at the first vibration.

What happens if you use metal clips instead of plastic ones?

Metal clips (for example, from the old “classics”) are not suitable for modern Nissan for three reasons:

1. They rust, which spoils the appearance of the interior.

2. When vibrating, the metal begins to “play”, which causes a creaking sound.

3. Microcracks form at points of contact with plastic, which will eventually lead to panel failure.

Where to buy clips for Nissan: review of trusted suppliers

The choice of where to buy depends on your priorities: speed, price or originality. Let's consider all the options:

1. Official dealers Nissan

Pros: 100% original parts with a guarantee, selection by VIN code.
Cons: the price is 2–3 times higher than analogues (for example, a clip 77110-4M000 costs 150–200 ₽ at the dealer and 50–80 ₽ on the Internet).

2. Online spare parts stores

Recommended sites:

• 🛒 Exist.ru — a large assortment, there are photographs and sizes.
• 🛒 Emex.ru — there are often discounts on original clips.
• 🛒 Avtoall.ru — convenient selection by car model.

⚠️ Attention: On AliExpress And Wildberries They sell cheap clips without markings. In 70% of cases they break during the first installation. Check reviews and ask the seller for a quality certificate.

3. Car accessories stores (for example, "AutoSpetsCenter")

Here you can find universal clips from Febi, Hella or Corteco. They are cheaper than the original ones, but often are not inferior in quality. The main thing is to check the sizes!

4. Showdown

If you need clips for a rare model (for example, Nissan Stagea WC34), try searching at disassembly sites. Prices are 5–10 times lower, but there is a risk of getting a worn part. Before purchasing, ask the seller to send a photo of the clip on both sides.

How to strengthen old clips if there is nowhere to buy new ones

Situation: you disassembled the panel, and the clips broke, and the nearest spare parts store is 200 km away. What to do? There are several temporary solutions:

1. Epoxy resin. Suitable for herringbone clips. Apply resin to the rod, insert into the hole and let cure for 12 hours. Minus: the next time you dismantle, you will have to break the clip.
2. Plastic clamps. If the clip comes out, you can fix the panel with a clamp by threading it through the technological hole. Unaesthetic, but reliable.
3. 3M double sided tape. For lightweight panels (for example, covering pillars in Nissan Juke). Glue on a grease-free surface!
4. Homemade clips from plastic bottles. Cut a strip of plastic, heat it with a lighter and bend it into a Christmas tree shape. Suitable for emergency situations.

⚠️ Attention: In models with the system Around View Monitor (all-round view) Do not use metal mounts or clamps near the cameras. This will cause signal interference and artifacts will appear on the screen.

If you have temporarily secured the panel with tape or clamps, be sure to replace the clips with normal ones as soon as possible. Vibrations and temperature changes will quickly destroy the improvised mount.

FAQ: Frequently asked questions about Nissan clips

Can clips from other brands be used in Nissan?

Theoretically yes, but only if they match head diameter, shaft length and material. For example, clips from Toyota Corolla E150 suitable for Nissan Almera G15 (article 90467-08016). However, for models with an aluminum body (Nissan GT-R R35) you need special clips with an anti-corrosion coating - analogues will not work.

How many clips do you need to replace a door trim?

The quantity depends on the model:

• Nissan Qashqai J10/J11 — 8 clips on the front door, 6 on the back.
• Nissan X-Trail T31/T32 — 10 clips for the front door (including speaker mounts).
• Nissan Patrol Y62 — 12 clips + 4 rubber seals.

Always take 1-2 more clips: they often break when removed.

What tool do you need to work with clips?

Minimum set:

• Plastic clip remover (eg KUKKO 21/1).
• Set of screwdrivers with flat and Phillips blades.
• Tweezers for removing broken clips.
• Hairdryer (if the clips are stuck).

For bumpers you will need additional socket wrench 10 — some clips are attached together with bolts.

What to do if the clip has fallen inside the panel?

Don't panic! Take magnetic telescopic grip (available at hardware stores) and carefully remove the clip. If there is no magnet:

1. Remove the panel completely.
2. Turn it over and shake it - the clip will fall out on its own.
3. If the clip is stuck in the body, use a wire with a hook.

B Nissan Teana L33 Clips often get lost in the air duct area. To find them, remove the glove compartment - “lost items” usually accumulate there.

How often should the clips be checked?

It is recommended to carry out a preventive examination:

• Every 30,000 km.
• After strong vibrations (for example, off-road driving).
• When preparing for winter, the cold makes plastic brittle.

Signs that the clips need to be replaced:

• Creaks when driving over uneven surfaces.
• Gaps between panels.
• Cracking sound when opening/closing doors.