Removing the rear sofa Nissan Qashqai may be needed in a variety of situations: from banal interior cleaning to electronics repair or upholstery replacement. However, many owners encounter difficulties - non-obvious fasteners, hidden latches or fear of damaging plastic elements. This article will help you understand all the nuances of the process, be it a model J10 (2006–2013), J11 (2013–2021) or fresh J12 (from 2021).

We will consider in detail not only the standard dismantling procedure, but also typical mistakes that beginners make. For example, why on the Qashqai J11 you cannot simply pull the seat up - this will lead to breakage of the guides. You will also learn what tools are really necessary (spoiler: often only a screwdriver is enough), and how to cope with the task without the help of a service. Get ready - the process is easier than it seems!

Preparing for removal: tools and safety precautions

Before you begin dismantling, make sure you have everything you need. The minimum set of tools depends on the generation Qashqai, but in 90% of cases it will be enough:

  • ✅ Flat head screwdriver (for prying off plastic plugs)
  • ✅ 10 or 12 mm socket wrench (for J10 mounts)
  • ✅ Plastic puller (so as not to scratch the casing)
  • ✅ Flashlight (lighting helps to find hidden latches)

On models J11 and J12 metal bolts are rare - the manufacturer switched to plastic clips and latches. However, if your Qashqai been in an accident or was repaired, the fasteners could have been replaced with non-standard ones. In this case it will be useful pliers And WD-40 for stuck elements.

⚠️ Attention: On vehicles with heated rear seats, before removing Be sure to disconnect the negative terminal of the battery. The contacts under the seat may close if you accidentally touch metal parts of the body.

Also prepare your workspace:

  • 🚗 Park the car on a flat surface (the slope will complicate access to the fastenings).
  • 🧹 Remove all things from the trunk - they will interfere when removing the backrest.
  • 📸 Take a photo of the location of the wires (if there is heating or an armrest with electronics).
📊 What generation of Nissan Qashqai do you have?
  • J10 (2006–2013)
  • J11 (2013–2021)
  • J12 (from 2021)
  • I don't know

Step-by-step instructions: removing the rear seat on a Qashqai J10 (2006–2013)

First generation Nissan Qashqai (index J10) has the most labor-intensive rear seat mounting system. Both plastic latches and metal bolts are used here. Follow the algorithm:

  1. Move the front seats forward all the way to free up space for maneuver.
  2. Find two bolts in the front of the sofa (under the decorative plugs). They are located at the base of the backrest, closer to the central tunnel.
  3. Unscrew the bolts socket wrench on 10 mm (on some modifications - 12 mm).
  4. Raise the sofa up with a little effort - it should come out of the grooves of the guides.

If the seat does not budge, check to see if any fastenings have gone unnoticed. On Qashqai J10 With all-wheel drive (4WD), there is sometimes an extra bolt in the middle - it's easy to miss.

☑️ Checklist for J10

Done: 0 / 5
⚠️ Attention: On heated sofas, after removing the bolts, do not pull the seat sharply - first disconnect the power connector (it is located under the central part). Pull the plastic clip, not the wires!

If you need to remove the backrest too, proceed as follows:

  1. Open the trunk and locate the two plastic caps at the bottom of the backrest (on the sides).
  2. Pry up the caps with a screwdriver and unscrew the bolts under them.
  3. Pull the backrest towards you - it will come out of the grooves.

Features of dismantling for Qashqai J11 (2013–2021) and J12 (from 2021)

Second and third generations Nissan Qashqai (J11 And J12) have lost most of the metal fasteners - now the seat is held on by plastic latches and guides. This simplified the process, but added nuances:

  • 🔧 On J11 The latches are located on the sides of the sofa (closer to the doors) and in the front.
  • 🔧 On J12 An additional latch has been added in the middle - it is easy to miss.
  • 🔧 The backrest on both generations is attached only with plastic fasteners (no bolts).

Algorithm for J11/J12:

  1. Move the front seats back and locate the two plastic tabs on the front of the sofa (underneath the trim).
  2. Press the tabs with a screwdriver and pull the seat up.
  3. If the sofa does not budge, check the side latches - they need to be pryed off with a puller.
  4. For the backrest: pull it up with a force of ~10 kg - the latches will come out of the grooves.

On Qashqai J12 with electric backrest (optional) before removal be sure to turn off the power (remove the battery terminal). Otherwise, the mechanism may lock.

💡

If the latches do not budge, spray them with silicone lubricant (not WD-40!). It does not corrode the plastic and will make dismantling easier.

Generation Sofa mounting type Backrest mounting type Availability of electronics
J10 (2006–2013) 2 bolts + latches 2 bolts (under caps) Heating (optional)
J11 (2013–2021) Plastic latches (4 pcs.) Fasteners without bolts Heating, USB port (optional)
J12 (from 2021) Latches + central lock Clamps + electric drive (optional) Heating, ventilation, USB-C

Common mistakes and how to avoid them

Even experienced car owners sometimes make mistakes when removing the rear seat. Here are the most common:

  • ❌ Sudden jerking of the seat — leads to breakage of plastic guides (especially on J11/J12). Always check that all latches are latched.
  • ❌ Ignoring wiring — if you do not disconnect the heating connector, you can break the wires or burn the fuse.
  • ❌ Lost bolts/plugs — on the J10, the bolts often fall under the seat. Use a magnetic holder.
  • ❌ Incorrect assembly — if you mix up the right and left sides of the sofa (on J12 they are asymmetrical), the seat will not fall into place.

Another typical problem is jammed latches on J11 after the winter period. The plastic becomes brittle in the cold, and when you try to remove the seat, the latches break. Solution:

  1. Warm up the interior to +15°C (use a stove or heater).
  2. Apply silicone grease to the latches.
  3. Pry up the fasteners not with a screwdriver, but with a plastic puller.
What to do if the latch is broken?

If the latch does break, don't panic. It can be replaced with a new one (article number for J11 - 84810-4M00A). A temporary solution is to secure the seat with ties through the holes in the rails, but this is not safe for passengers.

How to remove a sofa with heating or armrest

If your Nissan Qashqai equipped with heated rear seats or a central armrest, the process is complicated by the presence of wiring and additional fasteners. Let's consider the nuances:

For heated models:

  1. After removing the sofa, you will see the power connector under the central part. It could be:
    • 🔌 White — standard heating (J10/J11).
    • 🔌 Orange color — heating + ventilation (J12).
  • Press the plastic connector lock and carefully disconnect it.
  • If the wires are stuck, do not pull - spray contact cleaning and wait 5 minutes.

    • For models with armrest:

    • 🪑 The armrest is secured with two bolts under the decorative trim (unscrewed with a key on 10 mm).
    • 🔋 If the armrest has a USB port or 12V outlet, disconnect the connector before removing it.
    • 📦 In some configurations, a storage compartment is hidden under the armrest - check if there are any forgotten things there.

    On Qashqai J12 with premium audio system Bose A subwoofer can be located under the rear sofa. Its fastenings are not connected to the seat, but be careful when dismantling it - the speaker is suspended on rubber dampers that are easy to tear.

    💡

    On heated models, after reassembly, check the function before putting the sofa back in place. If the heating does not work, the problem may be in the oxidized contacts of the connector.

    Reverse installation: how to prevent squeaks and backlashes

    Putting the rear sofa back in place is a task no less important than removing it. Incorrect assembly results in creaks, backlashes or even incorrect heating operation. Follow these rules:

    • 🔧 Clean the guides from dirt and sand (use a vacuum cleaner or brush).
    • 🔧 Lubricate the plastic latches silicone grease (not lithol!).
    • 🔧 Check symmetry — on J12 the left and right sides of the sofa are different.
    • 🔧 Tighten the bolts (on J10) with force 8–10 Nm - overtightening deforms the thread.

    If squeaks appear after installation:

    1. Check whether the seat fits tightly into the grooves of the guides.
    2. Make sure that the decorative plugs do not rub against the plastic of the body.
    3. On heated models, check that the wire under the seat is not pinched.

    For Qashqai J11/J12 with a boltless fastening, after installation, press on the sofa weighing ~80 kg (sit on it) - this will help the latches to fully lock.

    ⚠️ Attention: On vehicles with the system Nissan ProPILOT (J12) a tire pressure sensor may be located under the rear seat (if there is no spare wheel). When installing the seat, be sure not to pinch the sensor wires.

    When to contact service: signs of serious problems

    Although removing the rear sofa Nissan Qashqai - a task that most car owners can handle; there are situations when it is better to trust the professionals:

    • 🔧 Broken guides — if the plastic fasteners are cracked during dismantling, parts will need to be replaced (see the table below for article numbers).
    • 🔥 Short circuit — if after removal the heating or USB port stops working, the problem may be in the fuse box.
    • 🛠️ Body deformation — on cars after an accident, the fastenings of the sofa can be displaced, and independent installation will lead to backlash.

    Cost of replacing fasteners in the service:

    Detail Article Cost (RUB) Note
    Sofa guide (J10) 84810-4M000 1 200–1 500 Pair (left + right)
    Fastening latch (J11/J12) 84810-4M00A 300–500 Per piece
    Heating connector 28430-4M000 800–1 200 Includes wires

    If you doubt your abilities, contact your authorized dealer. Nissan or to a trusted car service center. The average cost of work on removing/installing a rear sofa is 1,500–2,500 rubles (excluding spare parts).

    FAQ: answers to frequently asked questions

    Is it possible to remove the rear seat on a Qashqai without tools?

    On models J11 and J12 theoretically yes - the plastic latches can be snapped off manually, but the risk of breaking them is high. For J10 You can’t do without a screwdriver and a wrench (you need to unscrew the bolts). We recommend using at least a plastic puller to preserve the casing.

    How do you know if the seat is secured correctly?

    After installation, check:

    • No play when rocking the sofa with your hands.
    • Smooth fit to the floor (no gaps).
    • Heating performance (if any).
    • No squeaks when driving over uneven surfaces.

    On J12 Once installed correctly, you should hear a click from the latches.

    What should I do if the heating stops working after removal?

    The reasons may be as follows:

    1. The power socket is not connected (check the connection under the seat).
    2. The fuse has blown (on Qashqai this is usually F37 (15A) in the cabin block).
    3. The wiring is damaged (test the circuit from the connector to the control unit with a tester).
    4. The heating element has burned out (the sofa or its upholstery needs to be replaced).

    Start by checking the fuse and connector. If the problem persists, contact the service for diagnostics.

    Is it possible to wash a removed sofa at home?

    Yes, but with caution:

    • Use foam cleaner (For example, Autoglym or Sonax) and a soft brush.
    • Do not use washing vacuum cleaner — water may get into the heating elements.
    • To remove stains from upholstery do not use aggressive solvents (acetone, white spirit).
    • Dry the seat in shadows (direct sunlight will deform the plastic).

    If the sofa is very dirty, it is better to take it to interior dry cleaning — they use professional products that are safe for materials.

    Where is the fuse for heated rear seats in a Qashqai?

    Location varies by generation:

    • J10: fuse box in the passenger compartment, F37 (15A) (near the cigarette lighter fuse).
    • J11: block under the steering wheel, F28 (20A) (labeled "Seat Heater Rr").
    • J12: block in the glove compartment, F14 (20A) (marked "Rear Seat Heater").

    Before replacing the fuse turn off the ignition and remove the negative battery terminal.