Owners Nissan Tiida are often faced with the need to free up additional space in the car. This may be caused by the desire to transport long cargo, deep clean the luggage compartment, or replace the standard acoustics with a more powerful system. The process of dismantling the rear seat on this model is not difficult, but requires care and understanding of the design of the fasteners so as not to damage the trim or plastic elements.
Unlike many competitors, where the backrest simply reclines, Tienda (especially in the C11 body) requires physical removal of the cushion and backrest from the frame. The design provides for two types of fixation: the lower part is held due to the elasticity of metal brackets, and the upper part is held on hooks. Incorrect pulling force can cause fabric to warp or plastic clips to break, so it's important to be consistent.
Preparing tools and workspace
Before starting any active actions, it is necessary to provide access to the interior and prepare a minimum set of tools. In most cases, to remove the rear sofa on Nissan Tiida No specialized equipment is required, but having certain items on hand will make the task much easier and protect your car from scratches.
You will need a flathead screwdriver with a wide blade, preferably wrapped in duct tape or cloth to avoid scratching the plastic. A clean rag will also be useful to protect the floor if the seat elements fall. If you are planning further electrical work, for example, removing the speakers, prepare a set of 10 and 12 wrenches, as well as a Phillips screwdriver.
- 🛠 Flat-head screwdriver with a wide blade (scratch protection is required)
- 🧤 Work gloves to protect hands from sharp metal edges
- 🧹 Clean cloth or mats to protect the interior floor
Make sure the car is on a level surface and the handbrake is engaged. Open the trunk and lower the seats if they have the ability to fold, although this is not always critical for complete removal. Clear some space around the rear wheel arches so you have easy access to the lower airbag mounts.
Removing the lower seat cushion
The process should begin from the bottom, since it is the main supporting structure on which passengers are supported. Removal rear cushion on Nissan Tiida This is done by applying force to the front edge of the seat. This fastening is made in the form of metal brackets that hook onto hooks on the floor of the body.
Kneel next to the rear row of seats or, if space allows, inside the cabin. Locate the front edge of the cushion, closest to the doorway. Using a firm but controlled upward motion, pull the edge of the pillow. You need to overcome the force of the detent spring. If the seat does not move, check to see if there is an object underneath it that is blocking it.
⚠️ Attention: Do not try to pull the pillow towards you or to the side. The movement must be strictly vertical upward. Lateral forces can break the plastic guides or deform the metal frame, which will cause the seat to rattle during use.
Once one side has snapped open, repeat the process for the other side. The cushion should separate freely from the body. Be prepared for the fact that it can be heavy, especially if it has a reinforcement frame installed. Carefully remove it from the interior and put it in a safe place so as not to wrinkle the upholstery.
- 🔍 Inspect the mounting points on the floor for corrosion or dirt
- 🔧 Check the condition of the metal hooks to which the pillow clung
- 📦 Place the removed cushion in a place where it will not interfere with further work
- C11 (first generation)
- C12 (second generation)
- C13 (restyling)
- I don't know the exact model
Before removing the airbag, take a photograph of the location of the seat belts and fasteners so that during reassembly you do not mix anything up or tighten the belts incorrectly.
Features of removing the seat back
After removing the pillow, access to the backrest fastening mechanisms opens. Unlike a pillow, the back Nissan Tiida It is attached from above on special hooks and fixed from below. The process of removing it requires more care, since you are working with a larger and more fragile element containing the folding mechanisms and the armrest.
First you need to release the backrest from the lower fastening. If you have a split back model (60/40), you can remove each part separately. Locate the fasteners at the bottom of the backrest that fit into the grooves in the floor. They need to be raised or moved depending on the design. Often it is enough to simply pull the backrest towards you to remove the lower protrusions from the grooves.
The upper part of the backrest is supported by three or four hooks located along the upper edge. To remove it, you need to apply force towards yourself and upward, while simultaneously releasing the hooks. It is better to do this together: one person holds the back by the top, the second helps to remove the lower part from the grooves. If you are doing this alone, go slowly and control the angle.
⚠️ Attention: Be extremely careful with the armrest mechanism. When removing the backrest, it may get caught in the seat belt loops or openings in the floor, causing the fabric to rip or the plastic handle to break.
After detaching the backrests, inspect the hooks on the body. They often accumulate dust and dirt, which can make reinstallation difficult. If the hooks are bent, they must be carefully straightened to ensure the seat will remain securely in place in the future. Make sure that all fastening elements are intact and free of rust.
☑️ Check before removing the backrest
Working with the armrest and belt mechanism
Central armrest on Nissan Tiida is often the most problematic element during dismantling. It can be built into the backrest or be a separate module. If the armrest is built-in, its removal occurs along with the backrest, but requires attention to the hinges. If it is removable, it must be unscrewed or pulled out of the grooves before removing the main structure.
Seat belts also pose challenges. The top tether anchors often go through holes in the seat back. When removing the backrest, you must carefully remove the belt strap from the slot without jerking it sharply. If you plan to remove the entire backrest, you may need to unscrew the top belt fastener, but this is a more complex procedure, requiring a 12 or 14 wrench.
- 🔓 Inspect the slots in the seat belt trim for damage
- 🔧 If the armrest is removable, check the presence of mounting bolts under the decorative plugs
- 🧵 Do not allow the seat belts to twist during removal.
In some modifications, the armrest has a built-in hatch for transporting long loads. This mechanism may also prevent the backrest from being completely removed. Make sure that the hatch is closed or, conversely, open, depending on the design, to avoid jamming. Check that the sunroof control cables are not twisted.
What to do if the backrest cannot be removed?
Sometimes the backrest can become stuck to the hooks due to dirt or corrosion. Try to gently rock it up and down without applying too much force. If that doesn't work, use a plastic spatula to carefully pry off the hooks.
Nuances of the Nissan Tiida C12 and C13 model
Second and third generation Nissan Tiida (C12 and C13 bodies) have several differences in the design of the rear sofa compared to the first generation C11. In new models, the fastenings have become more complex, and the upholstery materials have become softer, which requires even greater care. Often a quick folding system is used, which may interfere with complete dismantling.
B Tiida C12 and C13 The lower clips of the cushion can be hidden under the plastic floor linings. They need to be carefully pryed and removed to gain access to the mounting brackets. Also, in these models, it is more common to separate the pillow into two parts, which simplifies removal, but increases the number of parts to account for.
⚠️ Attention: On models with Isofix, the fastenings are often integrated into the seat frame. When removing the cushion, make sure you do not damage the child seat anchors themselves, as replacing them is expensive and requires special equipment.
It is important to note that on restyled versions the shape of the upper mounting hooks may change. They can be made of more durable plastic or metal with a different profile. When purchasing new fasteners or replacing elements, be sure to check the part numbers, as they may not fit from the old model.
The design of the rear seat on the Nissan Tiida C12 and C13 is more complex than on the C11, and requires careful inspection of the hidden fasteners under the plastic linings.
Common mistakes and ways to avoid them
Many owners make the same mistake: they try to remove the backrest without first removing the pillow. This is physically impossible, since the pillow blocks access to the lower backrest mounting grooves. Also often forgotten are the seat belt latches, which can get caught on the frame.
Another common problem is using metal tools without protection. The sharp ends of screwdrivers easily leave deep scratches on the plastic panels of doors and floors. Always use a cloth or tape on the working end of the tool. This is a small thing that will save you money on restoring the interior.
- ❌ Do not use brute force to release the fasteners
- ❌ Do not leave removed parts in the sun or frost without protection
- ❌ Do not ignore the condition of hooks and loops before reinstallation
If you plan to leave the seats removed for a long period of time, it is recommended to cover them with protective film or cloth to avoid fading and staining. It is also worth checking the condition of the floor under the seats - moisture often accumulates there, which can lead to corrosion of the body.
Compatibility table and fastener specifications
For the convenience of selecting the necessary tools and understanding the specifics of fastenings on different generations of the model, a summary table is given below. It will help you quickly navigate the design features of your car.
| Generation | Pillow mounting type | Backrest mounting type | Features |
|---|---|---|---|
| C11 (2004-2011) | Metal staples | Hooks on top + slots on bottom | Simple design, hooks often rust |
| C12 (2011-2016) | Combination fasteners | Reinforced hooks | Presence of hidden bolts under the linings |
| C13 (2016-present) | Quick release locks | Plastic clips | More fragile items, care required |
| All models | General | General | Availability of Isofix in the rear seats |
When choosing tools to work with different generations Nissan Tiida Keep in mind that on new models the plastic is softer and cracks easily. On older vehicles, the main problem is corrosion and rusty fasteners, which may require the use of a penetrating lubricant.
How to check the serviceability of the fasteners?
Press the seat with your hands from different sides. If you hear a squeak or play, the fasteners are worn out or dirty. They need to be cleaned and lubricated with silicone grease.
FAQ: Frequently asked questions
Is it possible to remove the rear seat on a Nissan Tiida alone?
Yes, remove the back seat Nissan Tiida alone is quite possible, especially the bottom pillow. It is better to remove the backrest with an assistant, as it is heavy and uncomfortable, but with some skill you can do this yourself, using the correct lifting technique.
Do I need to unscrew the bolts to remove the sofa?
In the standard procedure for removing a sofa, there is no need to unscrew the bolts. All fastenings are made in the form of brackets and hooks. However, if you plan to completely disassemble the armrest or remove the seat belt mounts, then you will need to use 10- or 12-size wrenches.
What to do if the latches are stuck?
If the clamps are stuck, do not use brute force. Try treating the mechanism with a penetrating lubricant (for example, WD-40) and wait 10-15 minutes. Then gently rock the seat, trying to free the stuck element. As a last resort, you can use a plastic spatula to pry up the hook.
How to put the sofa back correctly?
Installation is carried out in reverse order. First engage the upper hooks of the backrest, then lower the lower part into the grooves and press until it clicks. Install the cushion by hooking the rear brackets to the hooks on the floor, and then sharply lowering the front edge until it locks. Listen for characteristic clicks confirming secure fastening.
Is it possible to transport cargo with the armrest installed?
Yes, on most models Nissan Tiida the armrest has a built-in hatch for transporting long cargo. However, if you have removed the entire backrest, the armrest must also be removed as it is part of the backrest structure.