How to remove the rear seat on a Nissan Micra: instructions with photos and tips

Rear seat in Nissan Micra (especially in models K13 And K14) may require dismantling to clean the interior, replace trim, repair electrical wiring, or access the fuel pump. Unlike many cars, where the seat can be removed in a couple of minutes, in Micra It has its own peculiarities - hidden latches, fragile plastic clips and non-obvious attachment points. If you act head-on, you risk breaking the fasteners or damaging the casing.

This article will help you avoid mistakes: here you will find step-by-step instructions with photos, a list of necessary tools, as well as unique nuances for different generations Micra (for example, differences in fastenings in versions with heated seats). We'll also go over how to properly disconnect the wiring if your car is equipped with seat belt sensors or rear airbags.

Preparation: Tools and Safety Precautions

Before you begin dismantling, make sure you have everything you need. Most fastenings in Nissan Micra plastic, so brute force is unacceptable here. Here's what you'll need:

• 🔧 Flat head screwdriver (for prying off plastic plugs). It is better to take a tool with a thin tip so as not to damage the casing.
• 🔨 10 or 12 mm socket wrench (for bolts securing the seat to the body - in some trim levels).
• 🧲 Magnetic holder or tweezers (so as not to lose small parts, such as pistons).
• 📸 Smartphone (to photograph the location of wires and fasteners before disconnecting).

Important: if your Micra equipped airbags in the rear seats (optional for European versions), before operation be sure to disconnect the battery for 10–15 minutes. This will prevent the squibs from accidentally firing. In models without airbags, simply remove the key from the ignition.

⚠️ Attention: Do not apply force to the seat back if it does not give in - in Micra K14 the lower part is attached to the body with bolts, which can be hidden under plastic plugs. An attempt to “rip out” the seat without unscrewing the bolts will lead to deformation of the metal frame.

Step-by-step instructions: Removing the lower part of the seat

Let's start with dismantling bottom pillow (the part on which the passenger sits). In most cases, it is attached to the body using two metal hooks at the front And latches at the back. Algorithm of actions:

1. Fold the seat back forward (if possible in your configuration). In some versions Micra the backrest is fixed - then skip this step.

2. Pry it up with a flat screwdriver plastic plugs on the front edge of the seat (usually there are two of them - one on each edge). Below them you will see bolts or metal hooks.

3. If the mount is on hooks, pull the seat sharply upward and towards yourself. If there are bolts, unscrew them with a socket wrench.

4. Unhook the seat from the latches at the back. To do this, you may need to press the plastic clips from the inside (use a screwdriver).

In models Micra K13 with heated seats Under the pillow you will find the power connector. To disconnect it:

1. Click on plastic retainer on the connector (usually orange or red).
2. Gently pull the connector towards you without tugging on the wires.

Is the battery disconnected (if there are airbags)|

Are the fastenings and wires photographed?

Do you have the tools to remove the plugs on hand?

Is there more room for maneuver (for example, the front seats have been moved)-->

Removing the rear seat back

Backrest in Nissan Micra attaches differently than a pillow. There are two options depending on the configuration:

Mounting type	Models	Tools	Features
Bolts from below	K12, basic versions K13	12 mm socket wrench	The bolts are hidden under a plastic panel in the trunk
Latches + bolt in the middle	K13 heated, K14	Screwdriver + 10 mm wrench	It is necessary to remove the trunk trim to gain access.
Clips on the sides	K14 (restyling)	Plastic puller	Risk of breaking clips during careless dismantling

For most versions the algorithm is as follows:

1. Remove plastic cover in the trunk (it blocks access to the lower back bolts). Carefully pry it off with a screwdriver, starting from the corner.

2. Unscrew the bolts securing the backrest to the body (usually there are 2–4 of them). B Micra K14 It may be necessary to remove part of the trunk trim.

3. If the backrest is secured with latches (as in K13), press them through the technological holes in the casing. They are usually located closer to the top of the back.

4. Lift the backrest up and remove it from the guides. Be careful - on some trim levels the seat belt sensor wires pass through here.

⚠️ Attention: B Nissan Micra K14 with the system ISOFIX the backrest can be rigidly connected to the body through metal brackets. Don’t try to “break it out” - look for hidden bolts under the decorative plugs!

Features for different generations of Micra

The design of the rear seat differs markedly depending on the generation and trim level. Here are the key details:

Nissan Micra K12 (2002–2010)

The simplest design:

• 🔩 Attaching the pillow - two metal hooks on the front and plastic latches on the back.
• 🔧 The back rests on two bolts, access to which opens after removing the lining in the trunk.
• ⚡ There is no electrical wiring (except for heated versions, but they are rare).

Nissan Micra K13 (2010–2017)

Here are the difficulties:

• 🔌 In versions with heated seats The power connector is hidden under the pillow. It needs to be disconnected to removing the seat, otherwise the wires may break.
• 🔒 The backrest can be attached not only with bolts, but also plastic clips on the sides. They are easy to break if you pull the back up without first squeezing it.
• 🚗 In some trim levels there is a wiring harness running under the seat seat belt sensors.

Nissan Micra K14 (2017–present)

The most complex design:

• 🔩 The pillow is attached to bolts (not hooks), which are hidden under the plugs.
• 🔧 The back has additional fastenings to the body through metal brackets (due to the ISOFIX system).
• ⚡ Electrical wiring is required - even in basic versions (belt sensors, airbags).

Where to look for hidden bolts in K14?

B Micra K14 the backrest mounting bolts are often hidden under decorative panel in the trunk (it is glued with double-sided tape). Carefully pry it off with a plastic puller, starting from the right corner. Under the panel you will find 2-3 10mm bolts. Do not try to remove the back without unscrewing them - this will lead to deformation of the metal frame.

Common mistakes and how to avoid them

Even experienced car owners make mistakes when removing the rear seat Micra. Here are the most common:

1. Broken plastic clips. The reason is an attempt to remove the backrest without releasing the latches. B K13/K14 The clips are fragile and cannot be restored. Solution: use plastic puller and press the latches through the technological holes.

2. Broken wires. This is especially true for heated versions. The reason is that they forgot to disconnect the connector before removing the seat. Solution: always take pictures of the wiring before dismantling.

3. Deformed frame. Occurs if you pull the seat without unscrewing the bolts (in K14). Solution: Check all attachment points to use of force.

4. Lost Pistons. Small plastic parts are easily lost when removing the plugs. Solution: use magnetic tray or tweezers.

If you break the clip, don't despair - it can be replaced. In auto parts stores for Nissan repair kits are sold (item number for Micra K13: 77110-4M000). For K14 will do 77110-5M000.

How to put the seat back

Assembly is no less important a process than dismantling. Here are the key points:

1. Make sure everything plastic clips on the spot. If they are broken, replace them before installation.

2. Connect electrical wiring (if any). Check that the connectors are seated until they click.

3. Place the seat cushion in place by hooking front hooks for the metal hinges of the body. Then press down on the back until the latches snap into place.

4. When installing the backrest, first wind it up top part into the grooves, then secure the bottom bolts.

5. Check your work seat belts and (if any) heated seats.

Important: after installation, check whether there are any gaps between the seat and the body. If the pillow “walks”, it means that the latches are not in place. In this case, remove the seat and repeat the installation.

When to remove the rear seat

Removing the rear seat Nissan Micra may be needed in the following cases:

• 🧹 Deep interior cleaning. Dust, sand and debris accumulate under the seat and cannot be removed with a vacuum cleaner without removal.
• 🔧 Electrical wiring repair. For example, if the heating or seat belt sensors do not work.
• 🛠️ Sheathing replacement. When the fabric is torn or heavily soiled.
• ⛽ Access to the fuel pump. B Micra The fuel filler flap is located under the rear seat (in some versions).
• 🚗 Installation of additional equipment. For example, a subwoofer or an alarm with motion sensors.

If you are planning interior cleaning, please note: under the seat in Micra Moisture often accumulates (especially if the car was used in winter). This can lead to corrosion of metal body parts. After cleaning, it is recommended to treat the metal anti-corrosion composition (For example, WD-40 or Molykote).

FAQ: Frequently asked questions

Is it possible to remove the rear seat in a Nissan Micra without tools?

In most cases, no. Even if the fastenings are snap-on (as in K12), to remove the plastic plugs you will need a flathead screwdriver. B K13/K14 You can't do without a socket wrench - there are bolts there.

What should I do if the plastic clip breaks when removing the backrest?

Clips can be purchased separately (part numbers are listed above in the article). If you don’t have time to wait for a spare part, temporarily secure the backrest with tape or zip ties, but do not operate the machine in this condition for a long time - it is unsafe.

How can I tell if my Micra has rear airbags?

Check the stickers on the pillars or in the glove compartment - there should be information about the number of airbags. Also inspect the back: if there is an inscription SRS AIRBAG or a pillow icon means they are installed.

Do I need to remove the trunk trim to access the backrest bolts?

B K13 Usually it is enough to remove the plastic cover. B K14 It may be necessary to partially dismantle the trim (especially if there is an ISOFIX system).

Can the removed seat be washed with water?

Yes, but with caution. Do not direct the water jet at foam base — it absorbs moisture and takes a long time to dry. It is better to use a damp cloth with car shampoo. To dry, leave the seat in the sun or use a hair dryer.