Owners Nissan Almera G15 generations are often faced with the need to access the space under the rear seat. This may be required to install a subwoofer, repair heating mechanisms, replace wiring, or simply transport long loads. The dismantling process does not require complex equipment, but it has its own nuances that are important to take into account in order not to damage the plastic clips or the upholstery.
Unlike some competitors where the seats are bolted on, Nissan Almera G15 uses a combined fastening system. The bottom of the pillow is held in place by metal hooks, and the back is secured with plastic pins and bolts. Understanding this design is the key to quickly and safely removing interior elements without unnecessary effort.
Preparing tools and workspace
Before starting work, you need to prepare all the necessary tools so as not to be distracted during the process. You will need a set of sockets, preferably with a ratchet, as well as a flat-head screwdriver or a special spatula for removing the clips. Having good interior lighting is critical as mounting points are often obscured by shadows.
Make sure the vehicle is on a level surface and the handbrake is set. It is recommended to remove all personal items from the back row, including rugs and items that could fall under the floor. This will prevent damage to the interior and simplify access to the places where the pillow is fixed.
- 🔧 10 mm socket with extension for unscrewing back bolts
- 🔨 Flat head screwdriver with soft tip or plastic spatula
- 🧤 Gloves to protect hands from sharp edges of metal and plastic
- 💡 Flashlight for illuminating hidden fastenings under the pillow
Removing the lower seat cushion
Lower part of the rear sofa Nissan Almera The G15 is attached to the body using two metal hooks at the front and clamps at the rear. Removal begins from the front part, since it is the main fulcrum. Lift the front edge of the cushion up using moderate force to release the hooks from the floor grooves.
If the seat does not give way, check if there are hidden bolts under it, which is rare, but possible in specific configurations. Usually it is enough to simply raise the edge by 5-7 centimeters. Once the hooks are released, gently pull the pillow towards you to remove it from the guides.
⚠️ Caution: Do not use excessive force when lifting the front part, as this may damage the upholstery or break the plastic mounting bracket, if provided by the design.
After removing the cushion, you will have access to the luggage compartment and hidden cavities. This is an ideal location for electrical work or installation of additional equipment. Carefully place the removed part in a safe place where it will not scratch the floor or doors.
- 🚗 Lift the front edge of the cushion to remove the hooks from the floor
- 🛠️ Pull the pillow towards you and up to completely detach
- 📦 Put the pillow in the trunk or on a flat surface
- Subwoofer installation
- Wiring repair
- Cargo transportation
- Just curiosity
Removing the backrest of the rear sofa
Rear seat back Nissan Almera G15 is more difficult to attach than a pillow. The main fastener is located at the top, where the backrest meets the trunk shelf. This uses bolts that need to be unscrewed with a 10 mm head. Sometimes they are difficult to access, so you may need to use a flexible extension cord.
After unscrewing the bolts, it is necessary to remove the plastic plugs that cover the fasteners. They can be pryed off with a flat screwdriver, but this must be done carefully so as not to leave marks on the plastic. Next, the backrest is held on the lower hinges, which need to be disengaged.
⚠️ Attention: When removing the backrest from the engagement, watch the wiring of the headrests, if they are removable, so as not to break the connectors.
If your equipment includes headrests, it is better to remove them in advance. To do this, press the headrest lock and pull it up. This will make it easier to remove the backrest and prevent it from being damaged when maneuvering in confined spaces in the cabin.
- 🔩 Unscrew the two upper backrest mounting bolts
- 🧹 Remove the decorative plugs from the mounting points
- 🔽 Pull the back up and towards you to bring out the lower loops
☑️ Backrest removal tools
Features of working with the folding mechanism
In some trim levels Nissan Almera The backrest folds in proportion to 60/40. The locking mechanism can be equipped with additional latches that require disconnecting the drive cable. If you plan to completely remove the backrest, the cable must be carefully unclipped from the lever.
To access the cable, it is often necessary to remove the side trim of the trunk. This is done by prying up the plastic pistons. Be extremely careful as the plastic on older cars can become brittle. If the piston does not give way, heat it with a hairdryer to make the plastic more elastic.
After disconnecting the cable, the backrest will be completely free. This allows you to remove it entirely, which is convenient when transporting large items. Make sure all fasteners are loose before attempting to remove the part from the interior.
What to do if the bolt is stuck?
If the backrest mounting bolt cannot be removed, do not use excessive force to avoid stripping the thread. Treat the joint with a penetrating lubricant such as WD-40 and wait 10-15 minutes. If this does not help, gently heat the bolt head with a hair dryer, expanding the metal.
Reinstalling the seat
Installing the seat is done in reverse order. First you need to fix the lower hinges of the backrest into the grooves of the floor. Make sure they go all the way in, otherwise the back will wobble. Then tighten the top bolts, but do not tighten them all the way right away to even out the gaps.
After the back is in place, check its rigidity. It should not dangle or make squeaks. Only then can the bolts be finally tightened to the manufacturer's specifications. Usually it is about 20-25 Nm.
The bottom cushion is easier to install: first the rear clips are inserted into the grooves, and then the front hooks engage the floor. Sit down on the seat to make sure it is secure. If there is a feeling of play, check the position of the hooks.
Before final tightening the backrest bolts, check that the head restraints are level and do not interfere with the closing of the trunk lid.
Use a torque wrench for final tightening to avoid warping the metal or damaging the threads. This is especially important for aluminum body parts that may be in the fastening area.
- 🔩 Insert the lower loops of the backrest into the grooves of the floor
- 🛠️ Tighten the top bolts and check the evenness of installation
- 🪑 Install the cushion by engaging the rear latches and front hooks
| element | Mounting type | Tool | Features |
|---|---|---|---|
| Bottom cushion | Metal hooks | Manual lift | Easy dismantling, no bolts |
| Upper backrest | M6 bolts | 10 mm head | Extensions required |
| Bottom of the backrest | Plastic/metal hinges | Manual take out | Sensitive to skew |
| Headrests | Spring clamps | Pressing a button | Removable before main dismantling |
Technical nuances and possible problems
When working with Nissan Almera G15 it is important to remember that some of the interior plastic parts are fragile. With age, plastic becomes brittle, so any actions with clips must be smooth. If the clip breaks, it is better to replace it immediately to avoid rattling on the road.
Another problem is the jamming of the folding mechanism. If the backrest does not fold, do not try to break it by force. Check that the drive cable is not twisted and lubricate the hinges with silicone grease. This will extend the life of the mechanism.
⚠️ Attention: Never leave removed items unattended in the cabin, as they may be damaged or stolen, especially if the car is parked.
If you plan to remove the seat frequently, consider installing additional handles or hinges for convenience. This will simplify the process and make it safer for the car body.
The correct sequence of actions is the key to success: first the pillow, then the back, and vice versa during installation. Failure to do so may result in damage to the fasteners.
Frequently asked questions (FAQ)
Is it possible to remove the backrest without removing the pillow?
Yes, technically this is possible, but it is extremely inconvenient. Maneuvering space is limited by the cushion and the bolts may be difficult to access. It is recommended to first remove the cushion to allow easy access to the upper mounts.
Do I need to disconnect the battery before removing the seat?
No, as standard Nissan Almera G15 There are no active electrical components in the rear seat that require power to be turned off. The exception is when you plan to work on heating wiring or speakers.
How to find the backrest mounting bolts if they are hidden?
The bolts are usually located under plastic plugs in the upper part of the backrest, near the trunk shelf. Carefully pry up the plugs with a screwdriver and you will see 10mm head holes.
What to do if the seat cannot be removed?
Check that all latches are released. Sometimes the backrest locking mechanism may become jammed. Try rocking your back a little back and forth while simultaneously lifting it up.
How long does it take to remove the rear seat?
An experienced master needs about 10-15 minutes. For the first time, allow 30-40 minutes to carefully study all the fasteners and avoid mistakes.
Regularly checking the condition of the fastenings and timely lubrication of the mechanisms will extend the life of the seats. If you are faced with a non-standard situation, it is better to contact specialists so as not to aggravate the problem. Remember that the safety of passengers depends on the reliable fixation of all interior elements.
Proper dismantling and installation of seats is not only a matter of convenience, but also of safety. Following the instructions will help you avoid damage to the interior and maintain the functionality of your vehicle for many years. Use quality tools and take your time so that all work is completed accurately.