Removing the front bumper Nissan Almera G15 - a task that owners face when repairing after an accident, replacing headlights, radiator grille or bumper. The process seems complicated only at first glance: if you know the sequence of actions and have the right tools at hand, you can do it in 30–60 minutes. In this article we will look at step by step instructions taking into account the nuances of a particular model, we will show video demonstration and warn you about typical mistakes that lead to breakage of fasteners or damage to the body.
Feature Almera G15 (2012–2019) - combined bumper mount: some of the bolts are hidden under plastic plugs, and some fasteners require careful removal. If you are planning to do this for the first time, we recommend reading the article to the end: here is unique techniques for removing clips without breaking them and a table with bolt sizes, which are often lost during disassembly.
Preparation: tools and working conditions
Before you begin, make sure you have everything you need. Working outside or in a garage with poor lighting can complicate the process - it is better to choose a level area with good access to light. Here minimal set of tools:
- 🔧 10 mm socket wrench or socket — for bolts securing the bumper to the side members.
- 🔨 Flathead screwdriver or plastic puller - for removing clips and plugs.
- 🔩 Phillips screwdriver (PH2) - for self-tapping screws at the bottom of the bumper.
- 🧲 Magnet or fastener container - so as not to lose small details.
- 🛠️ Jack and stops - if access to the lower fastenings is required.
If you are removing the bumper for painting or replacement, prepare in advance masking tape And polyethyleneto protect the headlights and grille from scratches. It will not be superfluous WD-40 - it will help to unscrew rusted bolts, which are often found at the bottom of the bumper after winter.
⚠️ Attention: Do not start work on a cold car! Plastic clips become brittle at temperatures below +10°C and may break during removal. If the car was parked in the cold, let it sit in a warm garage for 1-2 hours.
- In the garage
- On the street
- At the service station
- Houses in the yard
Step-by-step instructions: how to remove the front bumper
The dismantling process is divided into stages, taking into account the features Nissan Almera G15. Follow the sequence to avoid missing fasteners and damaging the body.
Step 1: Removing the Plastic Caps and Top Fasteners
Start at the top of the bumper. Here are located:
- Two bolts under the plugs on the sides (closer to the wings).
- Four clips under the radiator grille (you can see them if you look from above).
To get to the bolts:
- Carefully pry out the plastic plugs with a flat-head screwdriver (they sit on the latches).
- Unscrew the bolts with the head on
10 mm. - Remove the radiator grille by snapping off the clips on top (usually there are 4 of them).
☑️ Preparing the upper part of the bumper
Step 2: Removing the lower mounts and wheel arches
Let's move on to the bottom. Here you will need:
- 🔩 Unscrew the screws in the wheel arches (2-3 on each side, using a Phillips screwdriver
PH2). - 🔧 Unscrew the bolts from the bottom of the bumper (usually 2 pieces, with the head on
10 mm). - 🖐️ Snap off the plastic clips on the sides (they are clearly visible if you crawl under the car).
If access from below is difficult, you can raise the car with a jack (don't forget about the stops!). The main thing is not to pull the bumper by force until all the fasteners are unscrewed: this will lead to breakage of the clips.
⚠️ Attention: On Almera G15 after 2016, there may be additional screws at the bottom of the bumper near the fog lights. They are easy to miss if you do not first remove the plastic protection under the headlights!
Step 3: Detaching the bumper from the body
When all the bolts and clips are removed, all that remains is to carefully snap the bumper off the body. This is done like this:
- Have a helper support the bumper on one side to prevent it from falling.
- Start from one corner, gradually pulling the bumper towards you.
- Be careful not to break the fog light wires (if connected).
If the bumper doesn't work, check all the fasteners again - most likely you missed a screw or clip. On Almera G15 People often forget about the two bolts under the license plate!
What to do if the clip breaks?
If the retainer cracks when you remove it, do not try to put it back in - it will not hold the bumper. Buy a new clip (article number for Almera G15: 90510-4M000) and install it during reassembly. A temporary solution may be a plastic clamp, but this is unreliable!
Video instruction: removing the bumper on a Nissan Almera G15
For clarity, we recommend watching a video demonstrating the process. Pay attention to the points:
- 🎥 How the author removes clips without breaking them (a plastic puller is used).
- 🔧 Sequence of unscrewing bolts (from top to bottom).
- 🚗 Positioning the bumper when removing (so as not to damage the paint on the wings).
Video from YouTube (example of insertion, replace with the current ID):
<iframe width="560" height="315" src="https://www.youtube.com/embed/EXAMPLE_ID" title="Снятие бампера Nissan Almera G15" frameborder="0" allowfullscreen></iframe>If the video is not available, here are the key points from it:
| Stage | Time on video | Tip from the video |
|---|---|---|
| Removing the plugs | 0:45 | Use a flathead screwdriver covered with electrical tape to avoid scratching the plastic. |
| Unscrewing the bolts | 2:12 | Start with the top bolts so that the bumper does not sag under its own weight. |
| Removing the clips | 3:30 | Pull the bumper towards you smoothly, without jerking, so as not to break the latches. |
| Disconnecting Wiring | 4:50 | Before complete removal, disconnect the fog lamp connectors. |
If you are removing the bumper for painting, take a photo of the location of all the clips and bolts with your phone. When reassembling, this will help avoid mixing up the fasteners and save time.
Common mistakes and how to avoid them
Even experienced car owners make mistakes when removing the bumper. Here are the most common ones on Nissan Almera G15:
- 🔧 Skipping bolts under license plate — the bumper cannot be removed, and the clips break when you try to pull it off.
- 💥 Clip release force — plastic is fragile, especially in cold weather. It's better to use a puller.
- 🔌 Forgetting to disconnect the fog light wires — you can break the connectors or shorten the contacts.
- 🔩 Lost bolts and clips - Without a magnet or container, small parts get lost in the grass or garage.
Another common problem is paint damage on wings when removing the bumper carelessly. To avoid this, cover the edges of the wings with masking tape before work.
The most vulnerable part during dismantling is the clips under the headlights. They are easy to break if you pull the bumper up instead of first releasing the side clips.
Reassembly: how to install the bumper back
Installing the bumper takes place in the reverse order, but there are some nuances:
- Start with wiring connections fog lights (if equipped).
- Attach the bumper to bottom bolts first, then to the top ones.
- Insert the clips until they click - if the latch does not snap into place, it will fall out when moving.
- Check gaps between the bumper and the fenders: they should be the same on both sides.
After installation, check:
- 🔦 Operation of fog lights (if they are connected).
- 🚗 No squeaks or backlashes when pressing the bumper.
- 🎨 Color match (if the bumper was painted).
⚠️ Attention: If after installation the bumper “walks” or there is a gap between it and the fender, check whether you forgot to screw in the bolt under the headlight. On Almera G15 this is a common mistake!
Cost of work at a service station vs independent dismantling
If you doubt your abilities, you can contact the station. Here are the estimated prices for 2026:
| Type of work | Cost (₽) | Time (min) |
|---|---|---|
| Removing/installing the bumper | 1 500–2 500 | 40–60 |
| Replacement clips (1 pc.) | 200–400 | 10 |
| Adjusting the gaps | 500–1 000 | 20 |
Independent dismantling will only cost the cost of tools (if you don’t have them) and new clips (about 50–100 ₽ per piece). However, if you have never done this before, the risk of damaging your bumper or body increases. Weigh the pros and cons!
FAQ: Frequently asked questions about removing the bumper on the Nissan Almera G15
Do I need to remove the radiator grille to get to the bolts?
Yes, on Almera G15 The grille is attached to 4 clips on top and prevents access to the two upper bumper bolts. It is impossible to unscrew the bolts without removing it.
Is it possible to remove the bumper without an assistant?
Technically yes, but it’s inconvenient: the bumper weighs 5–7 kg, and it’s difficult to hold it with one hand while you snap off the clips with the other. It is better to invite an assistant or use supports.
Which clips break most often?
The most vulnerable are the side clamps near the headlights (article no. 90510-4M000) and clips under the license plate. It is recommended to buy them in reserve before work.
What to do if the bolt is rusty and cannot be unscrewed?
Process it WD-40 or similar lubricant, wait 10–15 minutes. If it doesn’t help, try screwing a nut onto the bolt and unscrewing it together with the bolt (the “nut on nut” method).
Do I need to remove the wheels to remove the bumper?
No, but if you plan to work on the wheel arches (for example, to replace the side member), then removing the wheels will make access easier. This is not necessary for standard bumper removal.