Removing the Nissan Qashqai door trim: instructions with photos and nuances

Removing the door trim Nissan Qashqai (especially models J10 And J11) is a task that owners face when replacing speakers, repairing power windows, or eliminating squeaks. It would seem that it could be simpler: pry up the plastic and remove the panel. But in practice, many are faced with broken clips, broken wires or damaged latches. The reason is ignorance of the design and lack of the right tool.

In this article we will analyze the process of removing the casing step by step, indicating hidden fastenings, which are often overlooked, and we will give recommendations on choosing tools. Let us separately dwell on the nuances for doors with electrical package without it, and we will also warn you against common mistakes that lead to expensive repairs. If you are planning the work yourself, read carefully to avoid unnecessary expenses on new parts.

Preparation: tools and materials

Before you begin dismantling, make sure you have everything you need. Using the wrong tools is a leading cause of damage to siding. For example, using a screwdriver instead of a plastic puller is almost guaranteed to leave scratches or break the clips.

Here minimum setwhich will be required:

• 🔧 Plastic pullers (or mediators) - 2-3 pieces. Metal tools must not be used!
• 🔩 Phillips screwdriver (usually PH2 or PH3 for screws in the handle and armrest).
• 🔧 Torx T20 or T25 - for some models Qashqai after 2014.
• 🧲 Magnet - so as not to lose small screws and clips.
• 📸 Smartphone - for photographing the location of wires and fasteners before dismantling.

Also prepare your workplace: doors should be completely open, and the interior is protected from accidental scratches. If you're working in a garage, make sure the lighting is bright enough to catch small details. For convenience, you can remove the threshold pad (if it interferes with access to the lower clips).

Step-by-step instructions: removing the door trim

The dismantling process can be divided into 3 stages: removal of decorative elements, unscrewing screws And detaching the clips. Let's start with the most obvious - the handle and armrest.

1. Removing the handle and armrest

In most versions Nissan Qashqai The door handle is attached to two screws hidden under a decorative trim. To remove it:

1. Pry up the handle cover plastic puller from the side (from the passenger compartment).
2. Gently pull it towards you - it should come out of the grooves.
3. Unscrew the two screws under the trim (usually PH2).

The armrest is attached in the same way: pry it from the back (closer to the back of the seat) and unscrew the screw. In some configurations there may be an additional clip - do not use excessive force so as not to break it.

2. Removing the speaker (if required)

If the purpose of disassembly is to replace the speaker, it can be removed before or after dismantling the casing. To do this:

• 🔊 Unscrew the 4 speaker mounting screws (usually PH2).
• 🔌 Disconnect the power connector by pulling the latch (do not pull the wires!).
• 📏 Measure the diameter and depth of the seat if you plan to install a new speaker.

Be careful: some versions Qashqai The speaker is additionally secured with latches. If it does not come out after unscrewing the screws, check for hidden fasteners around the perimeter.

3. Unscrewing the casing screws

Now we move on to the main panel fastening. The screws may be located in the following locations (see table below). Important: their number depends on the vehicle’s equipment!

Location	Number of screws	Screwdriver type	Notes
Under the door handle	2	PH2	Hidden under a decorative overlay
At the bottom of the casing (at the threshold)	1-2	PH2 or T20	Can be hidden by a cover
Behind the decorative speaker trim	1	PH2	Only in versions with audio preparation
In the door pocket (armrest)	1	PH2	Sometimes covered with a rubber mat

After unscrewing all the screws, the casing will still stick to plastic clips (usually 8-10 pieces around the perimeter). They need to be carefully snapped off, starting from the bottom corner of the door.

All screws are unscrewed (see table above)|

Speaker connectors are disconnected (if removed)|

Removed small parts (plugs, linings)|

A place has been prepared for storing clips and screws -->

4. Removing the trim from the clips

This is the most critical stage. The clips break easily if the panel is not pulled correctly. Proceed like this:

1. Insert the plastic puller into the gap between the trim and the metal part of the door at the bottom corner.
2. Apply gentle pressure to release the first clip. You will hear a characteristic click.
3. Move along the perimeter, gradually releasing all fasteners.
4. Once most of the clips are off, lift the trim up to clear it from the grooves at the top of the door.

Do not pull the panel towards you; it may get caught on window lift cable or electrical cables. After removing the trim, place it on a soft surface to avoid scratching it.

What to do if the clip breaks?

If the clip cracks or remains in the door, don't panic. It can be removed with pliers or carefully pry it out with a screwdriver. When reassembling, replace the broken clip with a new one (the cost of one is from 20 rubles). Do not use superglue or other improvisations - this will lead to squeaks or repeated dismantling.

Features for doors with electrical accessories

If your Nissan Qashqai equipped electric windows, mirrors or heating, when dismantling the trim you need to take into account additional nuances. The main danger is wiring damage or connectors.

Here's what to do before removing the panel:

• 🔌 Disconnect the battery terminal (negative) to avoid short circuit.
• 📸 Take a photo of the location of all connectors and wires on the back of the casing.
• 🔧 Prepare electrical tape or heat shrink tubing to insulate the contacts during reassembly.

After removing the trim, you will see the electrical package control unit (usually located at the bottom of the door). To disconnect the connectors:

1. Press the connector latch (usually a plastic tab).
2. Pull the connector straight at yourselfwithout pulling to the sides.
3. Mark the connectors if there are several of them (for example, with sticky tape with inscriptions).

Please note: in doors with heated mirrors additional wires pass through. They should not be bent or pulled - this may lead to breakage of the heating element.

Plastic pullers|

Metal screwdriver|

Knife or chisel|

Other (write in comments) -->

Common mistakes and how to avoid them

Even experienced car owners sometimes make mistakes when disassembling doors. Here are the most common ones and how to prevent them:

⚠️ Attention! Never pull on the corners or the speaker. The clips are located around the entire perimeter, and uneven force will lead to their breakage. Always start dismantling from the bottom corner.

Mistake 1: Using metal tools

Screwdrivers, knives or chisels scratch the plastic and break the clips. If you don't have plastic pullers at hand, you can use old bank cards or guitar picks - they are strong enough, but will not damage the casing.

Mistake 2: Skipping Hidden Screws

B Qashqai J11 Sometimes there is an additional screw under the decorative trim of the speaker or in the door pocket. If the casing cannot be removed, check again all possible attachment points (see table in the section above).

Error 3: Damage to electrical wiring

When disconnecting connectors, do not pull on the wires - only on the connector body! If the contacts are oxidized, clean them alcohol solution before reassembly. This will prevent problems with the operation of the window regulators in the future.

Mistake 4: Lost clips or screws

Small parts are easily lost in the interior. Use magnetic mat or a container with a lid for storage. It is better to fold the clips separately from the screws to avoid confusion during assembly.

Reassembly: nuances and tips

Reinstalling the sheathing seems easier than dismantling it, but there are pitfalls here too. Main rule: all connectors and wires must be connected before fixing the clips. Otherwise you will have to repeat the entire procedure again.

Procedure:

1. Connect all electrical accessories connectors (if they were disconnected). Check that the latches are latched.
2. Make sure that the window lift cable (in mechanical versions) is not twisted and lies in its groove.
3. Start installing the sheathing with top part, carefully sliding it into the grooves on the door frame.
4. Press down on the clip locations until you hear a characteristic click. Start at the corners, then move to the center.
5. Tighten all the screws (do not overtighten as this may strip the threads!).
6. Reinstall the handle, armrest and speaker.

After assembly, check the operation of all systems:

• 🔄 Window lifters (should move smoothly, without squeaks).
• 🔊 Speakers (check the sound at different frequencies).
• 🔥 Heated mirrors (if available) - turn it on and touch the glass after 2-3 minutes.

If after assembly there are extraneous sounds (creaks, crackling sounds), most likely the clips are installed incorrectly or the trim touches the metal parts of the door. In this case, you will have to repeat the dismantling and check all the fasteners.

Frequently asked questions (FAQ)

How many fastening clips are there on the Nissan Qashqai door trim?

The number of clips depends on the year of manufacture and configuration, but on average there are 8-12 pieces. Doors with power accessories may have 1-2 more clips due to additional fastenings for wiring. The exact quantity can only be found out after removing the trim - some clips are duplicated or hidden under decorative elements.

Is it possible to remove the casing without unscrewing the speaker?

Technically yes, but it will complicate the process. The speaker interferes with access to the clips at the top of the door, and there is a risk of damage to it when removing the trim. If the purpose of the analysis is not related to the audio system, we still recommend unscrewing the speaker - it will take no more than 5 minutes, but will save time and nerves.

What should I do if the window lifter does not work after assembly?

There may be several reasons:

1. Unconnected or incorrectly connected control unit connector.
2. Pinched or damaged wire.
3. The unit malfunctions (for example, after disconnecting the battery).

First, check the connectors and wires. If everything is ok, try reset error: Disconnect the battery for 10 minutes, then connect it back. In 80% of cases, this helps restore the operation of the window regulator.

Where to buy clips for Qashqai door trim?

Clips are available at any auto parts store. Nissan. The original ones have an article number 77110-4M000 (set of 10 pieces). Analogues from Toyota or Renault - they are identical in size. Average price of a set: 200-400 rubles. When buying, take it with a reserve - the clips often break during dismantling.

How to remove the rear door trim - are there any differences?

The process of removing the rear door trim Qashqai almost identical to the front, but there are several nuances:

• There are usually fewer screws (1-2 instead of 3-4).
• There may be 1-2 fewer clips, since the back door is lighter.
• In versions with children's castle You will first have to remove its decorative trim (it is secured with latches).

The main difference is the absence of an electrical package control unit (if the rear windows are not electric). This simplifies the process, but requires caution when working with the power window cable.