Removing the bumper on a Nissan Patrol: instructions with photos and tips from auto experts

Removing the bumper Nissan Patrol - a task that every owner of this legendary SUV faces sooner or later. Whether it is replacing headlights, installing a winch, repairing after an accident or tuning, dismantling requires accuracy and knowledge of the design features of the model. Unlike compact crossovers, The Patrol bumper is attached not only with bolts, but also with hidden latches, and its weight (up to 15 kg on the Y62) makes it difficult to work alone.

In this article we will look at the removal process front and rear bumpers on all generations Patrol (Y60, Y61, Y62), we indicate unique mounts for restyled versions 2014+, and also warn against typical mistakes that lead to breakage of clips or damage to the paintwork. If you plan to work without an assistant, prepare for physical exertion: even the Y61 plastic bumper weighs about 10 kg, and the Y62 metal frame requires the use of a jack or lift.

Preparation: tools and working conditions

Before you begin dismantling, make sure you have everything you need. Work for Nissan Patrol has its own nuances: for example, to remove the front bumper on a Y62 you will need Torx T30, which is rarely included in standard toolkits. Also prepare:

• 🔧 Set of sockets and ratchet wrenches (10 mm, 12 mm, 14 mm)
• 🔨 Screwdrivers: Phillips (PH2), flat, torx T20 And T30
• 🧲 Magnetic holder for bolts (so as not to lose fasteners in the engine compartment)
• 🔦 Flashlight or headlight (lighting under the bumper is usually insufficient)
• 🧴 Silicone grease or WD-40 (for rusted bolts on old Y60/Y61)
• 📦 Plastic clips (spare, since the original ones often break during dismantling)

If you are working in a garage, ensure good ventilation: dust and dirt will fall off the bumper when removed. For models Patrol Y62 with the system Around View Monitor (surround view cameras), be sure to disconnect the battery 10 minutes before starting work to avoid short circuits when disconnecting the connectors.

⚠️ Attention: On Nissan Patrol Y62 with factory winch bumper (ARB or Ironman 4x4) the fasteners are reinforced and may require a ratchet extension to remove them. Do not try to jerk the bolts off - this will cause the threads in the spar to break.

Removing the front bumper on Nissan Patrol Y61 (2004–2010)

Model Y61 considered one of the most repairable in the line Patrol, but there are pitfalls here too. Let's start with dismantling plastic lining (if installed). It is attached to 6 plastic clips and 4 screws T20 on the sides. Using a flat head screwdriver, carefully pry up the trim, starting at the corners, to minimize the risk of breaking the latches.

Next, let's move on to the main bumper:

1. Unscrew two bolts 12 mm in the upper part of the bumper (under the hood, next to the radiator grille).
2. Remove the wheels and unscrew one bolt at a time 14 mm on each side in the arch (they are hidden behind a plastic fender liner).
3. Disconnect the fog lights (if equipped) and parking sensor connectors (on models with Parking Sensor).
4. The bottom of the bumper is secured with 4 bolts 10 mm — it’s more convenient to unscrew them from a pit or a lift.

After unscrewing all the fasteners, the bumper will be held on by two lower latches. Pull it towards you with a force of about 20–30 kg - the latches should come out of the grooves. If the bumper does not budge, check that all the bolts are unscrewed (the fastening to the subframe is often forgotten).

Battery disconnected (for models with cameras)

Wheels removed (facilitates access to bolts in arches)

Spare clips have been prepared (the original ones often break)

All fastenings from below have been checked (4 bolts 10 mm)

-->

Features of removing the bumper on the Nissan Patrol Y62 (2010–present)

Bumper Y62 structurally more complex: fastenings for the system are added here Around View Monitor, sensors Blind Spot Warning and, in some versions, for winch bumper. Main differences from Y61:

• 🔧 Additional bolts T30 in the lower part (2 pieces, hidden behind plastic protection).
• 📹 Connectors for 4 all-round cameras (marked with yellow marks).
• 🚗 Fastening to the subframe is reinforced - bolts are used here 14 mm with increased tightening torque (45 Nm).
• 🔋 On hybrid versions (Patrol Hybrid) added connector for pedestrian recognition sensor.

Removal process:

1. Unscrew 2 bolts T30 at the bottom of the bumper (requires ratchet extension).
2. Remove the plastic protection under the engine (6 clips and 2 screws T20).
3. Disconnect the camera and sensor connectors. On models with ProPILOT Assist The connectors are secured with additional latches - they need to be pressed out with a screwdriver.
4. Unscrew 4 bolts 14 mm fastening to the subframe (access from below).
5. Remove the bumper along with the metal frame - on the Y62 they are one-piece (unlike the Y61).

⚠️ Attention: On Patrol Y62 with factory winch bumper ARB fastenings to the side members are reinforced with steel plates. When reinstalling, use a torque wrench - the tightening torque here is 60 Nm (versus standard 45 Nm).

Y60 (until 1997)

Y61 (1997–2010)

Y62 (2010–present)

Other (specify in comments) -->

Removing the rear bumper: nuances for all generations

Rear bumper on Nissan Patrol It is easier to remove than the front one, but there are some tricks here. On all generations (Y60, Y61, Y62) the fastenings are similar, with the exception of models with Rear View Camera and parking sensors. Let's start with preparation:

• 🔧 Open the trunk and remove the plastic trim on the sides (it is attached with 4 clips).
• 🔦 Illumination with a flashlight is required - bolts are often hidden by dirt.
• 🧴 Treat the body mounting bolts with WD-40 (especially on Y60/Y61).

Next follow the instructions:

1. Unscrew 2 bolts 12 mm in the trunk (on the sides, under the trim).
2. The bottom of the bumper is secured with 4 bolts 10 mm — it’s more convenient to unscrew them from the pit.
3. On models with Rear Parking Sensor disconnect the sensor connectors (they are located on the right and left).
4. If installed tow bar, unscrew the additional bolts 14 mm attaching the bumper to it.
5. Pull the bumper towards you - it will come off along with the plastic guides.

On Patrol Y62 with the system Intelligent Around View Monitor The rear bumper is equipped with an additional camera. Its connector is located on the right and is fixed with a plastic latch - do not pull the wires so as not to damage the contacts!

Table: Fastening elements for different generations of Patrol

Model	Front bumper	Rear bumper	Features
Nissan Patrol Y60 (until 1997)	4 bolts 12 mm, 2 screws T20	4 bolts 10 mm, 2 nuts 12 mm	Metal bumper, rusting bolts
Nissan Patrol Y61 (1997–2010)	6 bolts 12/14 mm, 4 clips	4 bolts 10 mm, 2 bolts 12 mm	Plastic cover with clips, parking sensors
Nissan Patrol Y62 (2010–present)	6 bolts 14 mm, 2 bolts T30, 4 clips	4 bolts 10 mm, 2 bolts 12 mm, camera connector	Cameras Around View, winch bumper
Patrol Y62 Hybrid	Optional: pedestrian sensor connector	Optional: High-definition rear camera connector	Reinforced fastenings, tightening torque 60 Nm

Common mistakes and how to avoid them

Even experienced car owners make mistakes when removing the bumper on Nissan Patrol. Here are the most common ones and how to prevent them:

• 🔧 Thread failure in the spar. Reason: Using the wrong key (for example, 13 mm instead of 14 mm) or jerky unscrewing. Solution: Always use a ratchet wrench with an extension and check the bolt size before working.
• 💡 Damage to camera connectors. On the Y62, the connectors are secured with plastic latches—they need to be pressed out rather than pulled by the wires. If the contacts are oxidized, treat them contact lubricant before disconnecting.
• 🔩 Lost bolts in the engine compartment. On Y61/Y62, the radiator grille bolts often fall into the niche under the headlight. Use a magnetic holder or prepare a container for fastening in advance.
• 🎨 Scratches on the body. The Y61/Y62 plastic bumper may rub against the paint when removed. Cover the edges of the body with masking tape before dismantling.

Another common problem is broken plastic clips. On the Y62, the clips securing the plastic bumper trim often break the first time it is removed. Buy a set of spare ones in advance (item number for Y62: Nissan 77110-4M000). If the clip breaks, do not try to put it back - it will not hold the bumper securely.

What to do if the bolt is stuck?

If the bolt does not come off even after using WD-40, try the following:

1. Heat the bolt with a hair dryer (do not overheat the plastic of the bumper!).

2. Use an impact driver or low-torque air impact driver.

3. As a last resort, drill out the bolt with a drill 0.5 mm smaller than the thread diameter, then cut a new thread with a tap.

Reinstalling the bumper: key points

Reinstalling the bumper on Nissan Patrol requires no less care than dismantling. Start by checking everyone rubber seals - they often get lost or torn when removed. On the Y62, seals are attached to the metal frame of the bumper and are responsible for the tightness of the system Around View Monitor.

Sequence of actions:

1. Reinstall the bumper, aligning all mounting holes. On Y62, first fix the metal frame, then the plastic cover.
2. Tighten the bolts in the following order: first the lower ones (to the subframe), then the side ones (in the arches), and lastly the upper ones (under the hood).
3. On models with cameras, connect the connectors until the bolts are fully tightened - this makes it easier to combine contacts.
4. Check the operation of all systems: fog lights, parking sensors, all-round cameras.

Pay special attention tightening torque:

• Bolts 10 mm — 25 Nm
• Bolts 12 mm — 35 Nm
• Bolts 14 mm — 45 Nm (60 Nm for winch bumpers)

After installation, check the gaps between the bumper and the body - they should be uniform (2-3 mm). If the bumper is crooked, loosen the bolts and adjust the position.

FAQ: Frequently asked questions about removing the bumper on a Nissan Patrol

Is it possible to remove the front bumper on a Y62 without a pit or lift?

Technically yes, but it is extremely inconvenient. Bottom bolts 10 mm And T30 are located very low, and without a hole you will have to work lying under the car. If there is no alternative, use a low-profile jack and stands for safety. On models with a winch bumper ARB Removal without a lift is almost impossible due to the weight of the structure (up to 25 kg).

What should I do if the fog lights do not work after installing the bumper?

The reasons may be the following:

• The power connector is not connected (check the contacts for oxidation).
• The fuse has blown (on Y61 this is F37 (10A), on Y62 - F22 (15A)).
• The wiring is damaged during dismantling (inspect the insulation for breaks).
• On Y62 with Intelligent Light System It may be necessary to reset the error via a diagnostic scanner.

Start by checking the fuse and connector. If the problem persists, use a multimeter to check the voltage at the lamp contacts.

How to remove the bumper on a Patrol Y60 with a metal frame?

On Y60 The bumper consists of a metal frame and a plastic lining. Dismantling process:

1. Unscrew 4 bolts 12 mm fastening the frame to the side members (2 on top, 2 on bottom).
2. Remove the plastic cover - it is secured with 6 screws T20 and 4 latches.
3. Disconnect the terminals from the fog lights (if installed).
4. Remove the metal frame along with the brackets - they are welded to it.

Please note: on the Y60, the bolts often rust. If they do not unscrew, cut them off with a grinder and install new ones (thread M8x1.25).

Do I need to remove the bumper to replace the radiator on the Patrol Y61?

No, not necessarily. To replace the radiator it is enough:

1. Remove the front grille (2 clips and 2 bolts 10 mm).
2. Unscrew the upper bumper fastenings (2 bolts 12 mm).
3. Move the bumper forward 10–15 cm (it will remain hanging on the lower mounts).

This will provide enough space to remove the radiator. Complete removal of the bumper will only be necessary if you need to replace the air conditioning condenser or cooling fans.

What clips are needed for the Patrol Y62 bumper?

For Nissan Patrol Y62 The following clips are used:

• Clips for fastening the plastic cover: Nissan 77110-4M000 (10 pieces per pack).
• Clips for attaching the bumper to the fender liners: Nissan 77110-1Y000 (4 pcs.).
• Clips for fastening the lower protection: Nissan 77110-3W000 (6 pcs.).

For winch bumpers ARB or Ironman 4x4 additional metal rivets will be required M8 (the article depends on the bumper manufacturer).