How to reset errors on a Nissan Qashqai: 5 proven methods (with photos and videos)

Errors on the dashboard Nissan Qashqai - a common problem that can occur even in a working car. Most often they appear after unsuccessful repairs, replacement of sensors or failures in the electrical system. But an error does not always mean a serious breakdown: sometimes it is quite simple resetto get rid of the annoying icon on the panel.

In this article we will look at all working methods for resetting errors on Qashqai J11 (2006–2013) and J12 (2013–2021), including methods without a scanner, using diagnostic equipment and even through CONSULT-III Plus. You will also learn which errors you can reset yourself, and which ones are better to contact the service.

Before you begin, remember: resetting errors does not eliminate their cause - if the problem is in the sensor or wiring, the icon will appear again after 1-2 engine start cycles. Therefore, after resetting, be sure to check the system to see if the code appears again.

1. How to determine the error code on a Nissan Qashqai without a scanner

If you don't have diagnostic equipment, you can try read the codes yourself through lamp flashing CHECK ENGINE. This method works on most Qashqai until 2017 release.

Instructions:

• 🔧 Turn off the ignition and make sure all doors are closed.
• 🔄 Press and hold the daily mileage reset button (located on the right of the instrument panel).
• 🔑 Turn the key to position ON (without starting the engine).
• 💡 After 5–10 seconds the lamp CHECK ENGINE starts flashing - this is the error code.

Interpretation of blinking:

• 🔢 Long flash (2–3 seconds) = tens.
• 🔢 Short blink (0.5 seconds) = units.
• 📌 For example, 2 long + 3 short = error P0203 (malfunction of the injector of the 3rd cylinder).

⚠️ Attention: On models with display between speedometer and tachometer (For example, Qashqai 2015+ Tekna) this method may not work - you will need a scanner or adapter ELM327.

2. Reset errors using buttons on the dashboard (without a scanner)

On Nissan Qashqai J11 (2006–2013) there is a hidden error reset function via a button combination. This method is suitable for non-critical errorssuch as P0420 (catalyst) or P0100 (mass air flow sensor).

Step by step instructions:

1. Turn off the ignition and close all doors.
2. Press and hold the button TRIP RESET (mileage reset).
3. Turn the key to position ON (without starting the engine).
4. Hold the button TRIP RESET 10–15 secondsuntil the message appears on the panel SELF DIAG.
5. Release the button and press it again - the errors should be reset.

⚠️ Attention: On Qashqai J12 (2013+) this method does not always work - it may be necessary diagnostic connector or scanner. If after resetting the error appears again, check sensor wiring or contact service.

3. Resetting errors by disconnecting the battery: pros and cons

One of the simplest ways is reset errors by disconnecting the battery. This method works on all generations Qashqai, but has its own nuances.

How to do it right:

• 🔋 Disable negative terminal battery (10 mm wrench).
• ⏳ Wait 15–20 minutes — this time is enough for errors to be reset ECU.
• 🔌 Reconnect the terminal and start the engine.

Advantages of the method:

• ✅ Does not require special equipment.
• ✅ Resets all temporary errors, including ABS, ESP And Airbag.

Disadvantages:

• ❌ Reset all settings: radio, clock, climate control.
• ❌ On Qashqai with system Intelligent Key Key retraining may be required.
• ❌ Does not eliminate hardware faults (for example, faulty oxygen sensor).

💡

Before disconnecting the battery, take a photo of the radio settings (unlock codes) and climate control - this will save time after connecting.

4. Using a diagnostic scanner: which one to choose and how to connect

For accurate error reset It's better to use a diagnostic scanner. On Nissan Qashqai fit:

• 📱 ELM327 Bluetooth (budget option, works with applications Torque Pro or OBD Car Doctor).
• 🔧 Launch CReader (supports advanced diagnostics Nissan).
• 💻 CONSULT-III Plus (professional equipment for dealership centers).

Connection instructions ELM327:

1. Insert the adapter into the connector OBD-II (located under the steering wheel, to the left of the pedals).
2. Connect to the adapter via Bluetooth (the password is usually 1234 or 0000).
3. Launch the application Torque Pro and select Nissan in the list of protocols.
4. Go to section Diagnostic Trouble Codes (DTC) and press Clear Codes.

⚠️ Attention: Cheap ELM327 (costing up to 500 ₽) errors are often not read ABS And Airbag on Qashqai J12. For a complete diagnosis it is better to use Launch X431 or Autel.

Scanner	Qashqai J11 support	Qashqai J12 support	ABS/Airbag reset	Price (2026)
ELM327 Bluetooth	✅ Yes	⚠️ Partially	❌ No	300–1000 ₽
Launch CReader V+	✅ Yes	✅ Yes	✅ Yes	5000–8000 ₽
Autel AL519	✅ Yes	✅ Yes	⚠️ Basic ones only	4000–6000 ₽
CONSULT-III Plus	✅ Yes	✅ Yes	✅ Full support	50 000+ ₽

5. Resetting ABS and Airbag errors: features and risks

System errors ABS And Airbag on Nissan Qashqai require a special approach. They cannot be reset by simply disconnecting the battery or using buttons - you will need special equipment or manipulation of the control unit.

Reset methods:

• 🔧 Scanner with support ABS/SRS (For example, Launch X431 or Autel MS906).
• 💻 Soft reset via Nissan DataScan (requires laptop and adapter CONSULT).
• 🔋 Reset by opening the fuse (does not work on all models).

⚠️ Attention: If the error ABS (For example, C1130 - pump malfunction) or Airbag (B1001 - open airbag circuit) appears again after reset, operating a car is dangerous. In this case, checking the sensors and wiring is required.

What happens if you ignore the ABS error?

If the ABS malfunctions, the braking system will continue to operate, but without the anti-lock function. This may result in skidding on slippery roads or longer braking distances. On some Qashqai models, when an ABS error is active, the exchange rate stability system (ESP) is also disabled.

6. Common errors on Nissan Qashqai and how to fix them

Some errors on Qashqai appear more often than others. Here are the most common codes and how to resolve them:

Error code	Description	Possible reason	How to fix
P0171	Lean fuel mixture	Air leaks, faulty mass air flow sensor, clogged injectors	Check the tightness of the intake manifold, clean the air flow sensor
P0300	Multiple Misfire (misfire)	Faulty spark plugs, coils, low fuel pressure	Replace spark plugs, check compression, diagnose fuel pump
C1130	ABS pump malfunction	Pump wear, connector corrosion, low voltage	Check the ABS fuse, measure the voltage on the block
B1001	Airbag circuit open	Damaged wire under the seat, faulty shock sensor	Check the connectors under the seats, diagnose the SRS unit
U1000	Lack of communication with the control unit	Poor contact in the CAN bus, discharged battery	Check the battery voltage, clean the contacts in the connectors

💡 Advice: If the error P0420 (catalyst) appears after refueling at an unfamiliar gas station, try it burn off deposits — drive 10–15 km at high speeds (3000–4000 rpm). Sometimes this helps clean the catalyst honeycomb.

7. When resetting errors does not help: what to do next

If the error appears again after resetting, it means there is a problem hardware room, not software. In this case:

• 🔍 Check the sensors (For example, DPKV, Mass air flow sensor, lambda probe) for damage.
• 🔌 Diagnose wiring — errors often occur due to oxidized or frayed contacts.
• 🛠️ Contact serviceif you are not confident in your abilities. For example, error P0340 (camshaft position sensor) may indicate timing chain wearwhich requires immediate repair.

⚠️ Attention: On Qashqai with engine MR20DD (2.0 l) common mistake P0011 (timing phase shift) may indicate chain stretch. Ignoring this problem leads to engine breakdown!

💡

If the error returns after 2-3 resets, further attempts are useless - repair or replacement of the faulty unit is required.

FAQ: Answers to frequently asked questions

Is it possible to reset the error? CHECK ENGINE without a scanner?

Yes, on Qashqai J11 This can be done with the mileage reset button (see. section 2). On J12 This method does not always work - you may need to disconnect the battery or the scanner.

Why does the error appear again after a reset?

This means the problem is not fixed. For example, if you reset the error P0130 (oxygen sensor), but the sensor itself is faulty, the code will return after 1-2 engine starts. In this case you need replace the sensor or check the wiring.

How to reset the error ABS on the 2015 Qashqai?

To reset ABS you need a scanner that supports this system (for example, Launch X431). Cheap ELM327 won't fit. Alternative is to turn off the fuse ABS (10A, unit under the hood) for 10 minutes, but this does not work on all models.

Is it possible to reset errors through an app on my phone?

Yes, but only if you have ELM327 or OBD2 adapter. Applications like Torque Pro or OBD Car Doctor Allows you to read and reset errors Engine, but do not always work with ABS And Airbag.

What should I do if the car does not start after resetting the errors?

This can happen if the learning process was interrupted during the reset. ECU (for example, when disconnecting the battery). In this case:

1. Check if the battery terminals are connected correctly.
2. Let the machine sit for 10-15 minutes (to ECU initialized).
3. Try starting the engine with the gas pedal depressed (throttle learning mode).
4. If it doesn’t help, contact the service for ECU flashing.