Setting the clock on a Nissan Qashqai: all the methods from A to Z

Time on the dashboard Nissan Qashqai - it would seem like a trifle, but it is precisely this that affects the correct operation of the on-board computer, navigation system and even diagnostic protocols. Many owners are faced with a problem when the clock gets lost after replacing the battery, multimedia firmware, or seasonal switch to winter/summer time. In this article we will look at all possible ways to set the time - from basic manual adjustment to synchronization via GPS and diagnostic scanner.

Feature Qashqai (especially models J10 And J11) is that the timing system is connected to the body control unit (BCM). This means that simply replacing the key battery or resetting errors can reset the clock. We will explain in detail how to avoid common mistakes and what to do if the time is regularly lost.

1. Preparing to set up: what you need to know before you start

Before you change the time, make sure that:

• 🔋 The car battery is charged (voltage is not lower than 12.4V). Low charge may interrupt the setup process and cause errors in BCM.
• 🔑 Ignition is turned on ON (engine is switched off). On some versions Qashqai adjustment is possible only with the engine running - this is indicated in the manual.
• 📡 If you plan to synchronize via GPS, check the signal of the navigation system (at least 3 satellites must be displayed on the multimedia display).
• 📄 The operating instructions for your modification are at hand - the menu location may differ for Qashqai 2014-2017 And 2018-2026.

On models with the system NissanConnect (2020+) time can be synchronized automatically via the Internet, but only with an active subscription to services Nissan. If the option is not available, you will have to configure it manually.

⚠️ Attention: On vehicles with push-button start (engine start button) do not press the brake pedal when setting - this may cause the system to go into ACC, where the clock menu is not available.

2. Manual time adjustment on the dashboard

This is the most universal method that works on all generations Qashqai. The instructions are suitable for analog and digital instrument panels.

Steps for setup:

1. Turn the ignition to position ON (do not start the engine).
2. Press and hold the button TRIP (or INFO on new models) within 3-5 secondsuntil the settings menu appears.
3. Using buttons ↑/↓ (or joystick on the steering wheel) select item Time Setting (or Clock in Russian firmware).
4. Click OK to enter editing mode.
5. Adjust hours and minutes using buttons +/–. On some versions, a button is used to switch between fields MODE.
6. Save your changes by clicking TRIP or OK one more time.

On Qashqai J12 (2022+) with a virtual dashboard, the time menu can be located in the section Vehicle Settings → Date & Time. It is accessed via touch buttons on the steering wheel or voice commands (if activated Nissan Voice Recognition).

3. Time synchronization via GPS (for models with navigation)

Cars Nissan Qashqai with the system NissanConnect Navigation (or old Nissan HDD Navigation) can automatically update the time via satellite signal. However, this function does not always work reliably - especially in urban environments with poor GPS reception.

How to enable auto-sync:

• 📡 Go to the navigation menu: Settings → System → Date and time.
• 🔄 Activate the option Auto-sync via GPS (or GPS Time Sync).
• 🌍 Select your time zone manually - this will speed up the process (for example, UTC+3 for Moscow).
• ⏳ Wait for the signal to update (may take up to 5-10 minutes).

If the time after synchronization is off by 1-2 hours, check:

• 📡 GPS signal quality (there must be at least 4 satellites on the navigation screen).
• 📅 Relevance of maps - outdated firmware may not process time zones correctly.
• 🔋 Power Saving Settings - If navigation goes to sleep, synchronization may be interrupted.

⚠️ Attention: On Qashqai J11 (2014-2021) with firmware 58.00.500 There is a bug: when auto-synchronizing, the time may be reset to 00:00 after turning off the ignition. The solution is to update the navigation software through the dealer or manually (instructions below).

How to update navigation firmware yourself

To update, download the current version of the software from the [Nissan Navigation Update](https://www.nissan-navigation.com) website. Unpack the archive onto a FAT32 formatted flash drive (up to 32 GB). Insert it into the car's USB port, turn on the ignition and follow the instructions on the screen. The process will take ~20 minutes. Don't turn off the power!

4. Setting the time via the multimedia system

On Qashqai with multimedia system NissanConnect (screens 7" And 8") time can be changed through the main menu. This method is convenient if the dashboard does not have separate buttons for settings.

Step by step instructions:

1. Click the button HOME on the central screen.
2. Go to Settings → System → Date and time.
3. Disable the option Auto-sync (if it is active).
4. Manually set the current time using the touch screen or control knob.
5. Select display format: 12 hour (AM/PM) or 24 hour.
6. Save the changes and reboot the system (turn off/on the ignition).

On some multimedia firmware, the time may be reset after updating the cards or resetting the settings. In this case:

• 🔄 Complete factory reset in the menu Settings → System → Reset.
• 📥 Update your media software via Nissan Connect Services (account and internet required).
• 🔧 Check the fuse F37 (10A) in the fuse box - it is responsible for powering the real time clock (RTC).

5. Reset time errors via diagnostic scanner

If the clock is on Qashqai go astray regularly (for example, after every trip), the problem may lie in errors in the body control unit (BCM). In this case, a diagnostic scanner with protocol support will help OBD-II.

Required equipment:

• 🔌 Adapter ELM327 or original Nissan Consult III/IV.
• 💻 Laptop/smartphone with the program Nissan DataScan, Torque Pro or FORScan.
• 🔋 Battery charger (in case of long-term diagnostics).

Procedure:

1. Connect the scanner to the connector OBD-II (located under the steering wheel, to the left of the pedals).
2. Launch the program and select a model Nissan Qashqai indicating the year of manufacture.
3. Go to section BCM (Body Control Module).
4. Read the errors - look for codes B1550, B1551 or U1000related to time synchronization.
5. Clear errors and run RTC reinitialization (function available in FORScan).
6. Disconnect the scanner, reset the battery terminals to 5 minutes and reset the time.

If the errors appear again, the problem may be:

Error code	Reason	Solution
B1550	Power supply fault RTC	Check the fuse F37 and wiring from the battery to BCM
B1551	Failed to sync with CAN bus	Update the firmware BCM through the dealer
U1000	Loss of communication with the control unit	Check the ground on the body (point under the hood, next to the battery)
C1130	Steering wheel angle sensor error (affects time in ESP)	Perform steering calibration via scanner

⚠️ Attention: On Qashqai with hybrid system (e-Power) error reset BCM may prevent the engine from starting. In this case, the key will need to be re-flashed by an authorized dealer.

6. Common problems and their solutions

Even after correct settings, the time Nissan Qashqai may behave incorrectly. Let's look at typical situations and ways to eliminate them.

Problem 1: The clock gets lost after replacing the battery

This is due to the fact that the block BCM loses power from the backup battery (RTC battery). Solution:

• 🔋 Install a new battery CR2032 to the block BCM (Removal of the instrument panel is required).
• 🔧 Disconnect the battery terminals at 10 minutes, then plug it back in and set the time again.
• 📡 If the problem persists, check the power circuit +12V Always (permanent positive) on the fuse block.

Problem 2: The time on the device and multimedia do not match

This occurs because the systems use different clock sources. Solution:

• 🔄 Reset media: hold down the button POWER on 10 seconds.
• 📵 Disable GPS auto-sync in navigation settings.
• 🔧 Update the multimedia firmware to the latest version (relevant for NissanConnect 2020+).

Problem 3: The clock freezes at one value

If the time on the instrument panel stops updating (for example, it freezes at 12:00), this indicates a malfunction of the quartz crystal in the BCM. In this case, replacement of the board or the entire module is required.

How to check if the RTC module is working properly

Connect the scanner and check the parameter RTC Status in the block BCM. If the value FAIL or NO DATA, the module is faulty. A temporary solution is to synchronize the time every time the engine is started.

7. Alternative setup methods

If standard methods do not help, you can use less obvious solutions.

Method 1: Setup via voice commands

On Qashqai J12 (2022+) with system Nissan Voice Recognition You can change the time by voice:

1. Activate the voice assistant using the button on the steering wheel.
2. Say: "Set time" or "Set clock".
3. Follow the voice prompts to enter the hours and minutes.

Method 2: Using a mobile application NissanConnect Services

For vehicles with support Connected Services:

• 📱 Install the application NissanConnect to a smartphone.
• 🔗 Connect to your car via Bluetooth.
• 🕒 In the section Vehicle Status find the option Sync Time.
• 🔄 Confirm synchronization - the time will be updated automatically.

Method 3: Manual programming via CAN bus

For advanced users: using Arduino or Raspberry Pi you can send a command to the block BCM to reset the time. Example code for Python:

import can
bus = can.interface.Bus(bustype='socketcan', channel='can0', bitrate=500000)
msg = can.Message(arbitration_id=0x7E0, data=[0x02, 0x2E, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00], extended_id=False)
bus.send(msg)

⚠️ This method requires knowledge in the field CAN hacking and can lead to errors in the system!

FAQ: Answers to frequently asked questions

Why, after replacing the battery, not only the time, but also the radio settings are lost?

On Nissan Qashqai block BCM and the radio are powered from one backup circuit. Disconnecting the battery resets all settings related to permanent memory (including radio, time and even window positions). To avoid this, use backup power supply (For example, power bank with an adapter for a cigarette lighter) when replacing the battery.

Is it possible to set the time via OBD connector without a scanner?

Technically yes, but this requires ELM327 adapter and a smartphone with an application Torque Pro or FORScan Lite. On the menu Custom PIDs you can manually send a command to the block BCM to adjust the time. However, this method requires knowledge CAN protocol and is not recommended for beginners.

Why is the time off by 1 hour on the Qashqai J11 (2014-2021) in winter/summer?

This is due to a firmware bug BCM in versions 58.00.400-58.00.500. The system does not process the transition to winter/summer time correctly. Solution:

1. Update the firmware BCM at the dealer (current version - 58.00.600+).
2. Disable GPS auto-sync in navigation settings.
3. Manually adjust the time zone to UTC+3 (excluding seasonal changes).

How to reset the time to factory settings?

To perform a full reset:

1. Disconnect the battery terminals at 15 minutes.
2. Plug it back in and turn on the ignition.
3. Press and hold the button TRIP on 10 secondsuntil the reset menu appears.
4. Select Reset All Settings and confirm.

⚠️ After the reset the following will also be reset:

• Climate control settings.
• Saved radio stations.
• Driver profiles (if available).

Where is the fuse for the clock?

On Nissan Qashqai J11/J12 circuit fuse RTC located in interior fuse box (under the glove compartment or behind the cover to the left of the steering wheel). Search:

• F37 (10A) - main fuse BCM.
• F20 (7.5A) — backup power supply for the clock (on some modifications).

Before replacing the fuse be sure to disconnect the batteryto avoid short circuit.