If you are faced with the need to replace the fastening clip 01553-09321 on your own Nissan, then you know: this small detail can cause big problems. A fallen bumper, loose trim or rattling plastic under the hood - all this is often associated with worn or broken clips. In this article, we will look at where this clip is used, how to choose it correctly (including original and non-original analogues), and also give step-by-step instructions for replacement without damaging the body.

Feature of the clip 01553-09321 lies in its versatility - it is used not only on Nissan Qashqai (J10/J11), but also on X-Trail T31/T32, Juke F15, as well as some models Renault And Datsun (thanks to the alliance Renault-Nissan). However, even within the same model, clips can differ in material and rigidity - many people find out about this only after an unsuccessful purchase. To avoid mistakes, we have collected verified data from owners and service technicians.

Where is clip 01553-09321 used in Nissan

This clip is a type piston clamps and is designed for attaching plastic elements to metal parts of the body. Main areas of application:

  • 🚗 Front and rear bumper — fixation to the wings and spars (especially important for Qashqai J11 after 2017).
  • 🔧 Lockers — fastening to the wheel arches (they often break during seasonal tire replacement).
  • 🔥 Engine compartment trim — fixing plastic panels above the radiator and battery.
  • 🚪 Door cards - in some modifications X-Trail And Pathfinder.

Important: clips 01553-09321 often confused with similar-designed but different-sized retainers, e.g. 01553-09320 (it is 3 mm shorter) or 01553-09322 (with reinforced base). If you install the wrong clip, the plastic will hang loose or crack during installation.

📊 What Nissan model do you repair?
  • Qashqai (J10/J11)
  • X-Trail (T31/T32)
  • Juke (F15)
  • Other model

Original vs analogues: what to choose and where to buy

Original clip from Nissan has an article number 01553-09321 and is sold in packs of 10–50 pieces. Average price per piece in official dealers - 120–180 rubles, but it is profitable to buy there only for wholesale orders. Alternative options:

Type Article/Brand Price per piece, ₽ Features
Original 01553-09321 (Nissan) 120–180 Guaranteed quality, but high price. Suitable for all alliance models.
Analogue (premium) Febi 27386 80–100 German quality, a little softer than the original. Suitable for Qashqai And X-Trail.
Analog (budget) Sasic 4000321 30–50 Made in China, tougher than the original. Risk of damage during installation.
Universal 3M 08577 60–90 Suitable for most Japanese cars, but may not match in diameter.

Where to buy:

  • 🛒 Official dealers - reliable, but expensive. Suitable if you need clips for warranty repairs.
  • 🌍 Online stores (Exist.ru, Autodoc, Kufar) - a wide selection of analogues, but check the reviews.
  • 🏗️ Auto parts markets - cheaper, but there is a high risk of running into a fake (especially clips Sasic).
⚠️ Attention: When purchasing analogues, pay attention to the material - high-quality clips are made from polypropylene (PP) or polyamide (PA). Cheap fakes made of ABS plastic break at the first winter temperature.

Step-by-step instructions for replacing the clip

To replace the clip 01553-09321 you will need:

  • 🔧 Flat screwdriver or plastic puller.
  • 🔨 Torx T20 key (for some models Nissan).
  • 🧴 Silicone grease (optional, to facilitate installation).

Sequence of actions:

  1. Removing the plastic panel. Carefully pry up the clip with a screwdriver, pressing on the center. Do not pull on the edge of the panel - this will break the fastener!
  2. Removing the old clip. If the clip breaks and a part remains in the hole, use pliers or a ⌀4 mm drill to carefully remove it.
  3. Installing a new clip. Insert it into the hole until it clicks. If it is tight, lubricate it with silicone (but not oil!).
  4. Fixing the panel. Press the panel until you hear a characteristic click. Check the secure fit by pulling on the edge.

Make sure the new clip is the right size

Prepare your tools (screwdriver, puller, pliers)

Clean the hole from dirt and rust

If you work in winter, warm up the clip with a hairdryer (plastic becomes brittle in the cold) -->

Tip: if the clip does not lock the first time, do not press harder - check to see if any debris has gotten into the groove. Often the problem lies in a deformed hole in the body, which needs to be corrected with a round needle file.

Typical replacement mistakes and how to avoid them

Even experienced car owners make mistakes that lead to repeated repairs. The most common:

  • 🔨 Using a metal screwdriver without protection. Scratches the plastic and increases play. Solution: wrap the screwdriver blade with electrical tape or use a plastic puller.
  • ❄️ Replacing clips in the cold. Plastic becomes brittle at temperatures below +5°C. Solution: warm up the clip and panel with a hairdryer or carry out work in a warm garage.
  • 🔩 Tightening the bolts next to the clips. This will deform the seat. Solution: tighten the bolts crosswise to a maximum torque of 5 Nm.
⚠️ Attention: If after replacing the clip the panel is still loose, check spacers under the clips (sometimes they get lost during disassembly). For Nissan Qashqai J11 original spacers have an article number 01553-4M00A.
What should I do if the clip breaks inside the hole?

If a piece of the clip remains in the body, do not try to pry it out with a screwdriver - this will widen the hole. It is better to use a thin drill (⌀3–4 mm) to drill out the remains, then use a tap to cut a new thread for the self-tapping screw (if the hole is critically enlarged). As a last resort, you can install the clip with epoxy glue, but this is a temporary solution.

How to extend the life of clips: prevention

Clips 01553-09321 They break down not only over time, but also due to improper use. To avoid frequent replacements:

  • 🚿 Wash your car properly. A jet of water under pressure (especially in car washes) washes the lubricant out of the clips. Use the gentle cycle or wash by hand.
  • 🔧 Lubricate the clips during seasonal maintenance. 1-2 drops of silicone grease into the seat once a year is enough.
  • 🌡️ Avoid sudden temperature changes. For example, do not wash a hot engine with cold water - this will deform the plastic.

Interesting fact: in Nissan Juke F15 clips 01553-09321 They often break on the rear bumper due to vibrations from the exhaust system. The solution is to install additional rubber dampers (part number 01553-4M01A).

💡

Before installing a new clip, apply a thin layer to its “skirt.” lithium grease - this will prevent squeaking and make future disassembly easier.

Comparison of clips for different Nissan models

Although the clip 01553-09321 considered universal, in some models Nissan its modifications are used. For example:

  • Nissan Qashqai J10 (2007–2013) - the clips are softer and often break when removing the bumper.
  • Nissan X-Trail T32 (2014–present) - clips with a reinforced base, but require precise fit.
  • Nissan Juke F15 — clips are 2 mm shorter, but interchangeable with 01553-09321 when installing spacers.

If you are unsure of compatibility, check the catalog Nissan EPC (Electronic Parts Catalog) by vehicle VIN code. For example, for Qashqai J11 2018 front bumper uses 8 clips 01553-09321 and 4 clips 01553-09322 (with metal core).

💡

Before purchasing clips, always check their compatibility with a specific attachment area - even within the same model Nissan Different types of fasteners can be used.

FAQ: Frequently asked questions about clip 01553-09321

Can clip 01553-09321 be used for Renault Duster?

Yes, but with reservations. The clip fits Renault Duster first generation (2010–2017) in the areas where the fender liners and rear bumper are attached. However, for the front bumper it is better to use the original clip Renault with article number 8200839338 — it has a reinforced lock.

How many clips 01553-09321 are needed for a complete replacement for a Nissan Qashqai J11?

To completely replace all clips with Qashqai J11 (2014–present) you will need:

  • Front bumper: 8 pcs.
  • Rear bumper: 6 pcs.
  • Fender liners (4 pcs per side): 8 pcs.
  • Engine compartment trim: 4 pcs.

Total: 26 pieces. We recommend taking extra (30–35 pcs.), since 1–2 clips may break when dismantling.

How can I replace the clip if I urgently need a replacement but don’t have the original?

Temporary alternatives:

  1. Self-tapping screw + Grover. Select a ⌀4 mm self-tapping screw with a press washer and a rubber groover. The downside is the risk of corrosion.
  2. Plastic dowel. Cut it to the desired length and flatten the edge to secure it.
  3. Adhesive sealant. Suitable for fixed panels (e.g. engine compartment trim). Use 3M VHB or Loctite 406.

Important: all temporary solutions must be replaced with original clips as soon as possible!

Why don't the new clips hold the panel?

There are several reasons:

  • The hole in the body is widened (a repair sleeve needs to be installed).
  • The clip is not the right height (check the article number).
  • The panel is deformed (for example, after an accident).
  • There is not enough spacer for the clip (relevant for X-Trail T32).

Solution: Remove the panel and check each clip separately. If the hole is loose, use a clip with a larger diameter (01553-09323).